Go to top
Price
-
Colours
81 products found
Go to Shop
Apollo Valve 10-400 Series Bronze Safety Relief Valve, ASME Hot Water, 50 psi Set Pressure, 3/4 NPT Female
Apollo Valve 10-400 Series Bronze Safety Relief Valve, ASME Hot Water, 50 psi Set Pressure, 3/4 NPT Female"
₱ 1,539.00
Galleon
This Apollo Valve 10-400 series safety relief valve has a bronze body, a 50 pounds per square inch (psi) relief pressure, a 3/4" female National Pipe Thread (NPT) inlet connection, and a 3/4" female NPT outlet. The valve's body and nozzle are bronze for resistance to corrosion, the seat is silicone for resistance to high temperatures, and the spring is stainless steel for resistance to corrosion. The valve can be used in operating temperatures up to 250 degrees F. This safety valve is American Society of Mechanical Engineers (ASME) safety rated for Section IV hot water heating boilers and hydronic heating systems. Relief valves remove excess pressure or vacuum from a system. The valve openings allow fluids or gases to escape to decrease pressure, and then close once the valve reaches the reseating pressure limit. They also relieve excess vacuum by opening to release a gas into the system and then closing after it reaches its low-pressure limit. Some relief valves have an adjustment mechanism to set the pressure where the valve opens, making it suitable for various applications. Relief valves are rated according to the volume of liquid or gas that can flow through them and the material that the valve is constructed from must be suitable for the fluid or gas, which may be corrosive or at an extreme temperature, in which it operates. Relief valves are used in a variety of applications, such as air compressors, petrochemical and chemical manufacturing, natural gas processing, and power generation. Apollo Valves manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention. The company, founded in 1928 and headquartered in Matthews, NC, meets international standard International Organization for Standardization (ISO)/IEC standard 17025:2005.
Read more
Go to Shop
Apollo Valve Apollo 106T Series Bronze Gate Valve, Class 150, Non-Rising Stem, 2-1/2 NPT Female
Apollo Valve Apollo 106T Series Bronze Gate Valve, Class 150, Non-Rising Stem, 2-1/2 NPT Female"
₱ 19,656.00
Galleon
This class 150 Apollo Valve 106T series bronze gate valve has a non-rising stem and female National Pipe Taper (NPT) threads on both ends. The bronze construction, solid wedge gate, and screw-in bonnet provide higher strength and resistance to corrosion than brass. The valve has a non-rising stem that stays fixed in place when the gate is raised or lowered for low clearance or underground use. The graphite internal packing helps prevent the valve’s stem from leaking. This gate valve is full port for reduced friction its inner diameter is the same as the inner diameter of the pipe it connects to enable maximum operating efficiency. The maximum pressure is 300 pounds per square inch (gauge) (psig) for cold working pressure (CWP) and 150 psig for steam working pressure (SWP), and it has a temperature range of -20 degrees F to 406 degrees F. It has female NPT threads on both ends for use with male threaded pipes. Mounted on top of the valve, a manually operated malleable iron hand wheel activates the inside screw mechanism, which lifts and lowers the gate to start and stop the flow between the connected pipes. This valve comes with a five-year warranty for workmanship and material defects. This class 150 valve meets Manufacturers Standardization Society (MSS) SP-80 for quality assurance. Class is a standard relating to tolerance, construction, dimension, and wall thickness, but it is not a direct measurement of maximum working pressure. The valve is appropriate for use in plumbing and heating piping applications, including use in building service pipe systems. Gate valves control flow in a piping system by lifting a gate out of the path of steam, fluids, or gases. They are designed to block or permit flow, as the vibrations and force of flow repeatedly striking a partly lowered gate can damage the gate and seats. To accommodate different flows and pressure requirements, gates come in four types: solid wedge (appropriate for almost all liquid service), flexible wedge (appropriate for steam service), split wedge (appropriate for normal temperature, non-condensing gas and liquid service, including corrosive service), and parallel disc (appropriate for high and low pressure applications). Hand wheels or levers activate the screw mechanism in the valve’s bonnet, which comes in various designs, to open and close the gate. Union bonnets are preferable for building service piping, threaded-in (or screw-in) bonnets work well for lighter-duty usage, and bolted body-bonnet connections are used primarily in iron multi-turn valves. Most gate valves have either a rising stem, which moves up and down with the gate, or a non-rising stem, which remains fixed in place. When closed, the gate and its seats form tight planar sealing surfaces, ideal for linear liquid flow. Gate valves are used in air, gas, liquid, and steam applications. Conbraco Industries, Inc. manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices under the Apollo Valves brand. The company, founded in 1928 and headquartered in Matthews, NC, meets international standard ISO/IEC 17025:2005 and makes products that meet International Organization for Standardization (ISO) and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 122T Series Bronze Globe Valve, Class 150, Inline, Union Bonnet, 3/8 NPT Female
Apollo Valve Apollo 122T Series Bronze Globe Valve, Class 150, Inline, Union Bonnet, 3/8 NPT Female"
₱ 3,828.00
Galleon
This class 150 Apollo 122T series inline bronze globe valve has a union bonnet, rising stem, polytetrafluoroethylene (PTFE) seat, and female National Pipe Taper (NPT) threads on both ends, and is used to control flow (throttling) in a pipeline or water plumbing system. The valve body is constructed of American Society for Testing and Material (ASTM) B62 bronze for strength and corrosion resistance, and has a PTFE seat. The valve’s maximum pressure is 300 pounds per square inch (gauge) (psig) for cold working pressure (CWP) and 150 psig for steam working pressure (SWP). It has a union bonnet to simplify inspection of the valve interior, and female NPT threads on both ends for connecting to male threaded pipes. This class 150 valve meets standard Manufacturers Standardization Society (MSS) SP-80 for quality assurance. Class is a standard relating to tolerance, construction, dimension, and wall thickness, but it is not a direct measurement of maximum working pressure. This rising stem globe valve is for use in various pipeline or water plumbing systems. Globe valves control flow rates in a piping system by the lift of a vertical stem and disk, which must be turned to open and close the valve. A seated disc extends into the center of the valve to act as a plug to restrict or open the flow path, depending on how tightly the valve stem is turned. The stem on globe valves can be either rising (moves up as the valve opens) to indicate if the flow is on or off, or non-rising (stem height remains constant when the valve is either open or closed) for use in small spaces. Globe valves are used in various water, gas, air, and steam piping systems that require frequent throttling operations. Conbraco Industries, Inc. manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices under the Apollo Valve brand. The company, founded in 1928 and headquartered in Matthews, NC, meets international standard ISO/IEC 17025:2005 and makes products that meet International Organization for Standardization (ISO) and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve 59 Series Bronze Y-Strainer with Tapped Cap, 1/4 NPT Female, 50 Mesh Screen
Apollo Valve 59 Series Bronze Y-Strainer with Tapped Cap, 1/4 NPT Female, 50 Mesh Screen"
₱ 1,815.00
Galleon
The Apollo YB strainers are designed to protect piping systems and process equipment from unwanted foreign particles with minimum pressure loss. Lightweight, compact protection against foreign particles. Corrosion resistant bronze body and stainless steel screens. 100 percent American made. 100 percent factory pressure tested. Removable self-aligning screen. Operating pressures to 400 psig. Working pressure: 125 psig at 350 degree F steam and 400 psig at 150 degree F water, oil, gas. Body: cast bronze, ASTM B584. Screen: 302 stainless steel. Approvals: CRN 0E8959.5C.
Read more
Go to Shop
Apollo Valve Apollo 102T-LF Series Bronze Gate Valve, Potable Water Service, Class 125, Non-Rising Stem, 1 NPT Female
Apollo Valve Apollo 102T-LF Series Bronze Gate Valve, Potable Water Service, Class 125, Non-Rising Stem, 1 NPT Female"
₱ 3,595.00
Galleon
This class 125 Apollo Valve 102T-LF series gate valve has a non-rising stem, female National Pipe Taper (NPT) threads, and lead-free bronze construction for potable water plumbing systems. The lead-free bronze construction, solid wedge gate, and threaded bonnet provide higher strength and resistance to corrosion than brass. The valve has a non-rising stem that stays fixed in place when the gate is raised or lowered for low clearance or underground use, and the graphite internal packing helps prevent the valve’s stem from leaking. This gate valve is full port for reduced friction its inner diameter is the same as the inner diameter of the pipe it connects to enable maximum operating efficiency. The maximum pressure is 150 pounds per square inch (gauge) (psig) for cold working pressure (CWP), and it has a temperature range of -20 degrees F to 406 degrees F. It has female NPT threads for use with male threaded pipes. Mounted on top of the valve, a manually operated malleable iron hand wheel activates the inside screw mechanism, which lifts and lowers the gate to start and stop the flow between the connected pipes. This valve comes with a five-year warranty for workmanship and material defects. The valve is certified as containing no more than 0.25 percent lead by weighted average on its wetted surfaces and complies with California AB1953, Vermont Act 193, Maryland HB372, and federal public law 111-380 for use with public drinking water. This class 125 valve meets Manufacturers Standardization Society (MSS) SP-139 and National Sanitation Foundation/American National Standards Institute (NSF/ANSI) 61-8, Annexes F and G standards for quality assurance. Class is a standard relating to tolerance, construction, dimension, and wall thickness, but it is not a direct measurement of maximum working pressure. The valve is appropriate for use in plumbing systems that convey or dispense water intended for cooking or human consumption. Gate valves control flow in a piping system by lifting a gate out of the path of steam, fluids, or gases. They are designed to block or permit flow, as the vibrations and force of flow repeatedly striking a partly lowered gate can damage the gate and seats. To accommodate different flows and pressure requirements, gates come in four types: solid wedge (appropriate for almost all liquid service), flexible wedge (appropriate for steam service), split wedge (appropriate for normal temperature, non-condensing gas and liquid service, including corrosive service), and parallel disc (appropriate for high and low pressure applications). Hand wheels or levers activate the screw mechanism in the valve’s bonnet, which comes in various designs, to open and close the gate. Union bonnets are preferable for building service piping, threaded-in (or screw-in) bonnets work well for lighter-duty usage, and bolted body-bonnet connections are used primarily in iron multi-turn valves. Most gate valves have either a rising stem, which moves up and down with the gate, or a non-rising stem, which remains fixed in place. When closed, the gate and its seats form tight planar sealing surfaces, ideal for linear liquid flow. Gate valves are used in air, gas, liquid, and steam applications. Conbraco Industries, Inc. manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices under the Apollo Valves brand. The company, founded in 1928 and headquartered in Matthews, NC, meets international standard ISO/IEC 17025:2005 and makes products that meet International Organization for Standardization (ISO) and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve 13-510 Series Bronze Safety Relief Valve, ASME Steam, 15 psi Set Pressure, 3/4 NPT Female
Apollo Valve 13-510 Series Bronze Safety Relief Valve, ASME Steam, 15 psi Set Pressure, 3/4 NPT Female"
₱ 1,860.00
Galleon
This Apollo Valve 13-510 series steam relief valve is a safety valve for protecting small to medium low-pressure steam heating boilers. It has a cast bronze body, a 15 pounds per square inch (psi) relief pressure, a 3/4" female National Pipe Thread (NPT) inlet connection and 3/4" female NPT outlet, and a PTFE (polytetrafluoroethylene) seat. The valve's body and nozzle are bronze and the spring is steel for resistance to corrosion. The flat seat is a PTFE-faced disc for positive seal, resistance to moisture and high temperatures, and positive drainage of condensate from the seat area. The valve can be used in operating temperatures up to 250 degrees F. This relief valve is American Society of Mechanical Engineers (ASME) safety rated for Section IV heating boilers and is suitable for low-pressure steam heating and supply boilers. Relief valves remove excess pressure or vacuum from a system. The valve openings allow fluids or gases to escape to decrease pressure, and then close once the valve reaches the reseating pressure limit. They also relieve excess vacuum by opening to release a gas into the system and then closing after it reaches its low-pressure limit. Some relief valves have an adjustment mechanism to set the pressure where the valve opens, making it suitable for various applications. Relief valves are rated according to the volume of liquid or gas that can flow through them and the material that the valve is constructed from must be suitable for the fluid or gas, which may be corrosive or at an extreme temperature, in which it operates. Relief valves are used in a variety of applications, such as air compressors, petrochemical and chemical manufacturing, natural gas processing, and power generation. Apollo Valves manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention. The company, founded in 1928 and headquartered in Matthews, NC, meets international standard International Organization for Standardization (ISO)/IEC standard 17025:2005.
Read more
Go to Shop
Apollo Valve 59LF Series Bronze Lead Free Y-Strainer, 1-1/2 NPT Female, 20 Mesh Screen
Apollo Valve 59LF Series Bronze Lead Free Y-Strainer, 1-1/2 NPT Female, 20 Mesh Screen"
₱ 9,133.00
Galleon
The Apollo Lead Free YB-LF (59LF Series) strainers are designed to protect piping systems and process equipment from unwanted foreign particles with minimum pressure loss. Lightweight, compact protection against foreign particles. Corrosion resistant bronze body and stainless steel screens. 100 percent factory pressure tested. Blowout ball valve option. Lead Free AB 1953 Certified. Made in USA. Operating pressures to 400 psig. Working pressure: 125 psig at 350 degree F steam and 400 psig at 150 degree F water, oil, gas. Body: cast bronze. Screen: 302 stainless steel.
Read more
Go to Shop
Apollo Valve 59 Series Bronze Y-Strainer, 1/2 NPT Female, 50 Mesh Screen
Apollo Valve 59 Series Bronze Y-Strainer, 1/2 NPT Female, 50 Mesh Screen"
₱ 1,805.00
Galleon
The Apollo YB strainers are designed to protect piping systems and process equipment from unwanted foreign particles with minimum pressure loss. Lightweight, compact protection against foreign particles. Corrosion resistant bronze body and stainless steel screens. 100 percent American made. 100 percent factory pressure tested. Removable self-aligning screen. Operating pressures to 400 psig. Working pressure: 125 psig at 350 degree F steam and 400 psig at 150 degree F water, oil, gas. Body: cast bronze, ASTM B584. Screen: 302 stainless steel. O-Ring: Teflon. Approvals: CRN 0E8959.5C.
Read more
Go to Shop
Apollo Valve 59LF Series Bronze Lead Free Y-Strainer, 1/2 NPT Female, 50 Mesh Screen
Apollo Valve 59LF Series Bronze Lead Free Y-Strainer, 1/2 NPT Female, 50 Mesh Screen"
₱ 2,062.00
Galleon
The Apollo Lead Free YB-LF (59LF Series) strainers are designed to protect piping systems and process equipment from unwanted foreign particles with minimum pressure loss. Lightweight, compact protection against foreign particles. Corrosion resistant bronze body and stainless steel screens. 100 percent factory pressure tested. Blowout ball valve option. Lead Free AB 1953 Certified. Made in USA. Operating pressures to 400 psig. Working pressure: 125 psig at 350 degree F steam and 400 psig at 150 degree F water, oil, gas. Body: cast bronze. Screen: 302 stainless steel.
Read more
Go to Shop
Apollo Valve YCT Series Cast Iron Y-Strainer, 1 NPT Female, 20 Mesh Screen
Apollo Valve YCT Series Cast Iron Y-Strainer, 1 NPT Female, 20 Mesh Screen"
₱ 1,919.00
Galleon
YCT Strainers are designed to protect piping systems and process equipment from unwanted foreign particles with minimum pressure loss. Install these hardworking strainers upstream in almost any application to protect valves, regulators, solenoids and meters from rust, dirt and pipe scale. Cast Iron, ASTM A126-B for Body, Cap/Cover and Plug. 304 Stainless steel screen. Graphite gasket. Working pressure (non-shock): 250 psig at 406 degree F for Steam 400 psig at 150 degree F for Water, Oil, Gas. CSA B-51 and CRN OE10274.5 approved.
Read more
Go to Shop
Apollo Valve 59 Series Bronze Y-Strainer, 1/4 NPT Female, 50 Mesh Screen
Apollo Valve 59 Series Bronze Y-Strainer, 1/4 NPT Female, 50 Mesh Screen"
₱ 1,768.00
Galleon
The Apollo YB strainers are designed to protect piping systems and process equipment from unwanted foreign particles with minimum pressure loss. Lightweight, compact protection against foreign particles. Corrosion resistant bronze body and stainless steel screens. 100 percent American made. 100 percent factory pressure tested. Removable self-aligning screen. Operating pressures to 400 psig. Working pressure: 125 psig at 350 degree F steam and 400 psig at 150 degree F water, oil, gas. Body: cast bronze, ASTM B584. Screen: 302 stainless steel. O-Ring: Teflon. Approvals: CRN 0E8959.5C.
Read more
Go to Shop
Apollo Valve Apollo 121T Series Bronze Globe Valve, Class 125, Inline, Threaded Bonnet, Bronze Seat, 1-1/2 NPT Female
Apollo Valve Apollo 121T Series Bronze Globe Valve, Class 125, Inline, Threaded Bonnet, Bronze Seat, 1-1/2 NPT Female"
₱ 10,517.00
Galleon
This class 125 Apollo 121T series inline bronze globe valve has a threaded bonnet, rising stem, bronze seat, and female National Pipe Taper (NPT) threads on both ends, and is used to control flow (throttling) in a pipeline or water plumbing system. The valve body and seat are constructed of American Society for Testing and Material (ASTM) B62 bronze for strength and corrosion resistance.The valve’s maximum pressure is 200 pounds per square inch (gauge) (psig) for cold working pressure (CWP) and 125 psig for steam working pressure (SWP). It has a threaded bonnet for tight assembly and reduced risk of leakage, and female NPT threads on both ends for connecting to male threaded pipes. This class 125 valve meets standard Manufacturers Standardization Society (MSS) SP-80 for quality assurance. Class is a standard relating to tolerance, construction, dimension, and wall thickness, but it is not a direct measurement of maximum working pressure. This rising stem globe valve is for use in various pipeline or water plumbing systems. Globe valves control flow rates in a piping system by the lift of a vertical stem and disk, which must be turned to open and close the valve. A seated disc extends into the center of the valve to act as a plug to restrict or open the flow path, depending on how tightly the valve stem is turned. The stem on globe valves can be either rising (moves up as the valve opens) to indicate if the flow is on or off, or non-rising (stem height remains constant when the valve is either open or closed) for use in small spaces. Globe valves are used in various water, gas, air, and steam piping systems that require frequent throttling operations. Conbraco Industries, Inc. manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices under the Apollo Valve brand. The company, founded in 1928 and headquartered in Matthews, NC, meets international standard ISO/IEC 17025:2005 and makes products that meet International Organization for Standardization (ISO) and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve 10-400 Series Bronze Safety Relief Valve, ASME Hot Water, 30 psi Set Pressure, 3/4 NPT Female
Apollo Valve 10-400 Series Bronze Safety Relief Valve, ASME Hot Water, 30 psi Set Pressure, 3/4 NPT Female"
₱ 1,505.00
Galleon
This Apollo Valve 10-400 series safety relief valve has a bronze body, a 30 pounds per square inch (psi) relief pressure, a 3/4" female National Pipe Thread (NPT) inlet connection, and a 3/4" female NPT outlet. The valve's body and nozzle are bronze for resistant to corrosion, the seat is EPDM (ethylene propylene diene monomer) for resistance to ozone and aging, and the spring is stainless steel for resistance to corrosion. The valve can be used in operating temperatures up to 250 degrees F. This safety valve is American Society of Mechanical Engineers (ASME) safety rated for Section IV hot water heating boilers and hydronic heating systems. Relief valves remove excess pressure or vacuum from a system. The valve openings allow fluids or gases to escape to decrease pressure, and then close once the valve reaches the reseating pressure limit. They also relieve excess vacuum by opening to release a gas into the system and then closing after it reaches its low-pressure limit. Some relief valves have an adjustment mechanism to set the pressure where the valve opens, making it suitable for various applications. Relief valves are rated according to the volume of liquid or gas that can flow through them and the material that the valve is constructed from must be suitable for the fluid or gas, which may be corrosive or at an extreme temperature, in which it operates. Relief valves are used in a variety of applications, such as air compressors, petrochemical and chemical manufacturing, natural gas processing, and power generation. Apollo Valves manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention. The company, founded in 1928 and headquartered in Matthews, NC, meets international standard International Organization for Standardization (ISO)/IEC standard 17025:2005.
Read more
Go to Shop
Apollo Valve 59LF Series Bronze Lead Free Y-Strainer, 1 NPT Female, 20 Mesh Screen
Apollo Valve 59LF Series Bronze Lead Free Y-Strainer, 1 NPT Female, 20 Mesh Screen"
₱ 4,776.00
Galleon
The Apollo Lead Free YB-LF (59LF Series) strainers are designed to protect piping systems and process equipment from unwanted foreign particles with minimum pressure loss. Lightweight, compact protection against foreign particles. Corrosion resistant bronze body and stainless steel screens. 100 percent factory pressure tested. Blowout ball valve option. Lead Free AB 1953 Certified. Made in USA. Operating pressures to 400 psig. Working pressure: 125 psig at 350 degree F steam and 400 psig at 150 degree F water, oil, gas. Body: cast bronze. Screen: 302 stainless steel.
Read more
Go to Shop
Apollo Valve YCT Series Cast Iron Y-Strainer, 3/4 NPT Female, 20 Mesh Screen
Apollo Valve YCT Series Cast Iron Y-Strainer, 3/4 NPT Female, 20 Mesh Screen"
₱ 1,647.00
Galleon
YCT Strainers are designed to protect piping systems and process equipment from unwanted foreign particles with minimum pressure loss. Install these hardworking strainers upstream in almost any application to protect valves, regulators, solenoids and meters from rust, dirt and pipe scale. Cast Iron, ASTM A126-B for Body, Cap/Cover and Plug. 304 Stainless steel screen. Graphite gasket. Working pressure (non-shock): 250 psig at 406 degree F for Steam 400 psig at 150 degree F for Water, Oil, Gas. CSA B-51 and CRN OE10274.5 approved.
Read more
Go to Shop
Apollo Valve Apollo 122T Series Bronze Globe Valve, Class 150, Inline, Union Bonnet, 1/2 NPT Female
Apollo Valve Apollo 122T Series Bronze Globe Valve, Class 150, Inline, Union Bonnet, 1/2 NPT Female"
₱ 3,148.00
Galleon
This class 150 Apollo 122T series inline bronze globe valve has a union bonnet, rising stem, polytetrafluoroethylene (PTFE) seat, and female National Pipe Taper (NPT) threads on both ends, and is used to control flow (throttling) in a pipeline or water plumbing system. The valve body is constructed of American Society for Testing and Material (ASTM) B62 bronze for strength and corrosion resistance, and has a PTFE seat. The valve’s maximum pressure is 300 pounds per square inch (gauge) (psig) for cold working pressure (CWP) and 150 psig for steam working pressure (SWP). It has a union bonnet to simplify inspection of the valve interior, and female NPT threads on both ends for connecting to male threaded pipes. This class 150 valve meets standard Manufacturers Standardization Society (MSS) SP-80 for quality assurance. Class is a standard relating to tolerance, construction, dimension, and wall thickness, but it is not a direct measurement of maximum working pressure. This rising stem globe valve is for use in various pipeline or water plumbing systems. Globe valves control flow rates in a piping system by the lift of a vertical stem and disk, which must be turned to open and close the valve. A seated disc extends into the center of the valve to act as a plug to restrict or open the flow path, depending on how tightly the valve stem is turned. The stem on globe valves can be either rising (moves up as the valve opens) to indicate if the flow is on or off, or non-rising (stem height remains constant when the valve is either open or closed) for use in small spaces. Globe valves are used in various water, gas, air, and steam piping systems that require frequent throttling operations. Conbraco Industries, Inc. manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices under the Apollo Valve brand. The company, founded in 1928 and headquartered in Matthews, NC, meets international standard ISO/IEC 17025:2005 and makes products that meet International Organization for Standardization (ISO) and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 70-100 Series Bronze Ball Valve with Automatic Drain, Two Piece, Inline, Latch-Lock Lever, 3/4 NPT Female
Apollo Valve Apollo 70-100 Series Bronze Ball Valve with Automatic Drain, Two Piece, Inline, Latch-Lock Lever, 3/4 NPT Female"
₱ 2,972.00
Galleon
The Apollo 70-100 series two-piece inline ball valve with an automatic drain is made of bronze and has a latch-lock lever handle and female National Pipe Taper (NPT) threaded connections on both ends. This valve is made of bronze for higher strength and corrosion resistance than brass. This valve is primarily for use in pneumatic applications it has an automatic drain for releasing air pressure from the pneumatic system to which it is connected. When the valve is in the on position, the drain vent is closed off when the valve is in the off position, air from the downstream system is vented to the atmosphere. This ball valve has a stainless steel latch-lock lever handle with a stainless steel nut and a vinyl sleeve for manual on/off control. The lever handle can be locked in either the open or closed position. The pounds per square inch (gauge) (psig) rating for this valve is 600 for water, oil, and gas (WOG) and 150 for saturated steam. It is inline for connecting two pipes going in the same direction and has NPT threads on both ends for creating tighter seals than straight threads. Reinforced polytetrafluoroethylene (RPTFE) seats and multifill polytetrafluoroethylene (MPTFE) stem packing reduce the risk of valve leakage. This ball valve is standard (or regular) port for reduced valve size and cost and has a working temperature range of -20 to 450 degrees Fahrenheit. This valve is for use in water and air applications only and meets standard MSS SP-110 for quality assurance. Ball valves use a spherical disc to control the flow between pipes, tubes, or hoses. Flow is allowed when the hole that pierces the ball-shaped disc is in line with the inlet and outlet of the valve. Flow is blocked when the ball is horizontally swiveled 90 degrees, so that the hole of the ball is perpendicular to the opening of the valve. Ball valves can be referred to as full port or reduced port (also known as regular or standard port) depending on the inner diameter of the valve. A ball valve is full port if the hole of the ball is the same size as the inner diameter of the connecting pipeline (resulting in lower friction) and is reduced port if the hole of the valve is one pipe size smaller than the pipe, resulting in less flow through the valve than through the shaft of the pipe. Ball valves may have a handle or lever that aligns with the ball’s position (open or closed) for manual operation. They are primarily used in air, gas, liquid, and steam applications. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve 61LF-500 Series Bronze Lead Free Ball Cone Check Valve, In-Line, Soft Seat, 3/8 NPT Female, 400 psi/125 psi Pressure
Apollo Valve 61LF-500 Series Bronze Lead Free Ball Cone Check Valve, In-Line, Soft Seat, 3/8 NPT Female, 400 psi/125 psi Pressure"
₱ 1,809.00
Galleon
The Apollo Valve 61LF-500 series Ball Cone check valve is a lead-free inline valve, and has a soft seat. The valve body and seat are made of bronze for higher resistance to corrosion than brass. Reinforced polytetrafluoroethylene (RPTFE) Ball Cone provides higher chemical resistance. It has female National Pipe Taper (NPT) threads for connecting to male threaded pipes, creating a tighter seal than straight threads. The maximum pressure rating is 400 pounds per square inch (psi), and the maximum steam pressure is 125 psi. The maximum temperature is 350 degrees Fahrenheit. This valve is lead free and complies with California's AB 1953 law for safe drinking water. Check valves have two ports and restrict the flow of fluids and other loose materials through a pipe or passageway to one direction. Flow enters through one port and exits through the other, closing when flow reverses or stops. Two common types of check valves are ball cone valves and swing check valves. A ball cone valve utilizes a spring-loaded ball seated against a cone-shaped interior surface to stop the flow of fluid in a forward direction, and a swing check valve has a movable disc on a hinge to block reverse flow. Check valves are rated by their cracking pressure (the minimum upstream pressure required for the valve to operate), and they are used in various water, gas, air, and steam lines. Apollo Valves manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention. The company, founded in 1928 and headquartered in Matthews, NC, meets international standard International Organization for Standardization (ISO)/IEC 17025:2005 and makes products that meet International Organization for Standardization (ISO) and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 76-100 Series Stainless Steel Ball Valve, Two Piece, Inline, Latch-Lock Lever with Nut, 1-1/4 NPT Female
Apollo Valve Apollo 76-100 Series Stainless Steel Ball Valve, Two Piece, Inline, Latch-Lock Lever with Nut, 1-1/4 NPT Female"
₱ 13,524.00
Galleon
The Apollo 76-100 series two-piece inline ball valve is made of stainless steel and has a latch-lock lever handle and female National Pipe Taper (NPT) threaded connections on both ends. This valve is made of stainless steel for resistance to corrosion and has a stainless steel latch-lock lever handle with a stainless steel nut and vinyl sleeve for manual on/off control. The lever handle can be locked in either the open or closed position. The maximum pressure is 2,000 pounds per square inch (gauge) (psig) for water, oil, and gas (WOG) for 1/4” to 1” valves, 1,500 psig for 1-1/4” to 2”, 1,000 psig for 2-1/2” to 3”, and 150 psig for all valves for saturated steam, and the temperature range is -20 to 450 degrees Fahrenheit. The valve is inline for connecting two pipes going in the same direction and has NPT threads on both ends for creating tighter seals than straight threads. Reinforced polytetrafluoroethylene (RPTFE) seats and multifill polytetrafluoroethylene (MPTFE) stem packing reduce the risk of valve leakage and this ball valve is standard (or regular) port for reduced valve size and cost. This valve is for use with water lines, processing plants, and agricultural applications and meets standard MSS SP-110 for quality assurance. Ball valves use a spherical disc to control the flow between pipes, tubes, or hoses. Flow is allowed when the hole that pierces the ball-shaped disc is in line with the inlet and outlet of the valve. Flow is blocked when the ball is horizontally swiveled 90 degrees, so that the hole of the ball is perpendicular to the opening of the valve. Ball valves can be referred to as full port or reduced port (also known as regular or standard port) depending on the inner diameter of the valve. A ball valve is full port if the hole of the ball is the same size as the inner diameter of the connecting pipeline (resulting in lower friction) and is reduced port if the hole of the valve is one pipe size smaller than the pipe, resulting in less flow through the valve than through the shaft of the pipe. Ball valves may have a handle or lever that aligns with the ball’s position (open or closed) for manual operation. They are primarily used in air, gas, liquid, and steam applications. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 161T Series Bronze Swing Check Valve, Class 125, Bronze Seat, 1/4 NPT Female
Apollo Valve Apollo 161T Series Bronze Swing Check Valve, Class 125, Bronze Seat, 1/4 NPT Female"
₱ 2,112.00
Galleon
Go to Shop
Apollo Valve Apollo 77-100 Series Bronze Ball Valve with Actuator Mounting Pad, Two Piece, Inline, Lever, 1-1/4 NPT Female
Apollo Valve Apollo 77-100 Series Bronze Ball Valve with Actuator Mounting Pad, Two Piece, Inline, Lever, 1-1/4 NPT Female"
₱ 5,994.00
Galleon
The Apollo 77-100 series two-piece inline full port ball valve with actuator mounting pad is made of bronze and has a lever handle and female National Pipe Taper (NPT) threaded connections on both ends. This valve is made of bronze for higher strength and corrosion resistance than brass and has a mounting pad for attaching a quarter-turn electric or pneumatic actuator to provide automated operation. It has a zinc-plated steel lever handle with a vinyl sleeve for manual on/off control. This valve is full port for reduced friction its inner diameter is the same as the inner diameter of the pipe it connects to enable maximum operating efficiency. The maximum pressure is 600 pounds per square inch (gauge) (psig) for water, oil, and gas (WOG) and 150 psig for saturated steam, and the temperature range is -20 to 450 degrees Fahrenheit. The valve is inline for connecting two pipes going in the same direction and has NPT threads on both ends for creating tighter seals than straight threads. Reinforced polytetrafluoroethylene (RPTFE) seats and a PTFE seal reduce the risk of valve leakage. This valve is for use in water lines, processing plants, and agricultural applications and meets standard MSS SP-110 for quality assurance. Ball valves use a spherical disc to control the flow between pipes, tubes, or hoses. Flow is allowed when the hole that pierces the ball-shaped disc is in line with the inlet and outlet of the valve. Flow is blocked when the ball is horizontally swiveled 90 degrees, so that the hole of the ball is perpendicular to the opening of the valve. Ball valves can be referred to as full port or reduced port (also known as regular or standard port) depending on the inner diameter of the valve. A ball valve is full port if the hole of the ball is the same size as the inner diameter of the connecting pipeline (resulting in lower friction) and is reduced port if the hole of the valve is one pipe size smaller than the pipe, resulting in less flow through the valve than through the shaft of the pipe. Ball valves may have a handle or lever that aligns with the ball’s position (open or closed) for manual operation. They are primarily used in air, gas, liquid, and steam applications. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 75-100 Series Bronze Ball Valve with Automatic Drain, Two Piece, Inline, Lockable Lever, 3/4 NPT Female
Apollo Valve Apollo 75-100 Series Bronze Ball Valve with Automatic Drain, Two Piece, Inline, Lockable Lever, 3/4 NPT Female"
₱ 3,743.00
Galleon
The Apollo 75-100 series two-piece inline ball valve with automatic drain is made of bronze and has a lockable lever handle and female National Pipe Taper (NPT) threaded connections on both ends. This valve is made of bronze for higher strength and corrosion resistance than brass. This valve is primarily for use in pneumatic applications it has an automatic drain for releasing air pressure from the pneumatic system to which it is connected. When the valve is in the "on" position, the drain vent is closed when the valve is in the "off" position, air from the downstream system is vented to the atmosphere. This valve has a zinc-plated steel, lockable lever handle that can be locked in either the open or closed position using a portable lock (not included). The pounds per square inch (gauge) (psig) rating for this valve is 600 for water, oil, and gas (WOG) and 150 for saturated steam. It is inline for connecting two pipes going in the same direction and has NPT threads on both ends for creating tighter seals than straight threads. Reinforced polytetrafluoroethylene (RPTFE) seats and multifill polytetrafluoroethylene (MPTFE) stem packing reduce the risk of valve leakage. This ball valve is standard (or regular) port for reduced valve size and cost and has a working temperature range of -20 to 450 degrees Fahrenheit. This valve is for use in water and air applications only and meets standard MSS SP-110 for quality assurance. Ball valves use a spherical disc to control the flow between pipes, tubes, or hoses. Flow is allowed when the hole that pierces the ball-shaped disc is in line with the inlet and outlet of the valve. Flow is blocked when the ball is horizontally swiveled 90 degrees, so that the hole of the ball is perpendicular to the opening of the valve. Ball valves can be referred to as full port or reduced port (also known as regular or standard port) depending on the inner diameter of the valve. A ball valve is full port if the hole of the ball is the same size as the inner diameter of the connecting pipeline (resulting in lower friction) and is reduced port if the hole of the valve is one pipe size smaller than the pipe, resulting in less flow through the valve than through the shaft of the pipe. Ball valves may have a handle or lever that aligns with the ball’s position (open or closed) for manual operation. They are primarily used in air, gas, liquid, and steam applications. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 70-100 Series Bronze Ball Valve, Two Piece, Inline, Lever, 3/4 NPT Female
Apollo Valve Apollo 70-100 Series Bronze Ball Valve, Two Piece, Inline, Lever, 3/4 NPT Female"
₱ 1,608.00
Galleon
The Apollo 70-100 series two-piece inline ball valve is made of bronze and has a lever handle and female National Pipe Taper (NPT) threaded connections on both ends. This valve is made of bronze for higher strength and corrosion resistance than brass and has a zinc-plated steel lever handle with a vinyl sleeve for manual on/off control. The maximum pressure is 600 pounds per square inch (gauge) (psig) for use with water, oil, and gas (WOG) and 150 for saturated steam. The valve is inline for connecting two pipes going in the same direction and has NPT threads on both ends for creating tighter seals than straight threads. Polytetrafluoroethylene (PTFE) reinforced seats and seals reduce the risk of valve leakage. This ball valve is standard (or reduced or regular) port for reduced valve size and cost and has a working temperature range of 0 - 500 degrees Fahrenheit. This valve is for use in water lines, processing plants, and agricultural applications and meets standard MSS SP-110 for quality assurance. Ball valves use a spherical disc to control the flow between pipes, tubes, or hoses. Flow is allowed when the hole that pierces the ball-shaped disc is in line with the inlet and outlet of the valve. Flow is blocked when the ball is horizontally swiveled 90 degrees, so that the hole of the ball is perpendicular to the opening of the valve. Ball valves can be referred to as full port or reduced port (also known as regular or standard port) depending on the inner diameter of the valve. A ball valve is full port if the hole of the ball is the same size as the inner diameter of the connecting pipeline (resulting in lower friction) and is reduced port if the hole of the valve is one pipe size smaller than the pipe, resulting in less flow through the valve than through the shaft of the pipe. Ball valves may have a handle or lever that aligns with the ball’s position (open or closed) for manual operation. They are primarily used in air, gas, liquid, and steam applications. Conbraco Industries, Inc. manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices under the Apollo Valves brand. The company, founded in 1928 and headquartered in Matthews, NC, meets international standard ISO/IEC 17025:2005 and makes products that meet International Organization for Standardization (ISO) and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 70-100 Series Bronze Ball Valve with Automatic Drain, Two Piece, Inline, Lever, 1/2 NPT Female
Apollo Valve Apollo 70-100 Series Bronze Ball Valve with Automatic Drain, Two Piece, Inline, Lever, 1/2 NPT Female"
₱ 2,585.00
Galleon
The Apollo 70-100 series bronze two-piece inline ball valve with automatic drain has a lever handle and female National Pipe Taper (NPT) threaded connections on both ends. This valve is made of bronze for higher strength and corrosion resistance than brass. It is primarily for use in pneumatic applications it has an automatic drain for releasing air pressure from the pneumatic system or tool to which it is connected. When the valve is in the on position, the drain vent is closed off when the valve is in the off position, air from the downstream system is vented to the atmosphere. This valve has a zinc-plated steel lever handle with a vinyl sleeve for manual on/off control. Reinforced polytetrafluoroethylene (RPTFE) seats reduce the possibility of leakage. The valve is standard (or regular) port for reduced valve size and cost. It has National Pipe Taper (NPT) threads for creating tighter seals than straight threads. The maximum pressure ratings are 600 pounds per square inch (gauge) (psig) for use with water, oil, and gas (WOG) and 150 psig for saturated steam, and the temperature range is -20 to 450 degrees Fahrenheit. This ball valve is for use in water lines, processing plants, and agricultural applications and meets standard MSS SP-110 for quality assurance. Ball valves use a spherical disc to control the flow between pipes, tubes, or hoses. Flow is allowed when the hole that pierces the ball-shaped disc is in line with the inlet and outlet of the valve. Flow is blocked when the ball is horizontally swiveled 90 degrees, so that the hole of the ball is perpendicular to the opening of the valve. Ball valves can be referred to as full port or reduced port (also known as regular or standard port) depending on the inner diameter of the valve. A ball valve is full port if the hole of the ball is the same size as the inner diameter of the connecting pipeline (resulting in lower friction) and is reduced port if the hole of the valve is one pipe size smaller than the pipe, resulting in less flow through the valve than through the shaft of the pipe. Ball valves may have a handle or lever that aligns with the ball’s position (open or closed) for manual operation. They are primarily used in air, gas, liquid, and steam applications. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 70-600 Series Bronze Ball Valve, Two Piece, 3-Port Diverting, Lever, 3/8 NPT Female
Apollo Valve Apollo 70-600 Series Bronze Ball Valve, Two Piece, 3-Port Diverting, Lever, 3/8 NPT Female"
₱ 1,747.00
Galleon
The Apollo 70-600 series two-piece three-port diverting ball valve is made of bronze and has a lever handle and female National Pipe Taper (NPT) threaded connections on both ends. This valve is made of bronze for higher strength and corrosion resistance than brass and has a zinc-plated steel lever handle with a vinyl sleeve for manual control. This ball valve is three-port diverting to regulate flow among three sections of pipe. Its maximum pressure is 400 pounds per square inch (gauge) (psig) for use with water, oil, and gas (WOG). It has NPT threads on both ends for creating tighter seals than straight threads. Reinforced polytetrafluoroethylene (RPTFE) seats and a PTFE seal reduce the risk of valve leakage. This ball valve is standard (or regular) port for reduced valve size and cost and has a working temperature range of -20 to 450 degrees Fahrenheit. This valve is for use in water lines, processing plants, and agricultural applications and meets standard MSS SP-110 for quality assurance. Ball valves use a spherical disc to control the flow between pipes, tubes, or hoses. Flow is allowed when the hole that pierces the ball-shaped disc is in line with the inlet and outlet of the valve. Flow is blocked when the ball is horizontally swiveled 90 degrees, so that the hole of the ball is perpendicular to the opening of the valve. Ball valves can be referred to as full port or reduced port (also known as regular or standard port) depending on the inner diameter of the valve. A ball valve is full port if the hole of the ball is the same size as the inner diameter of the connecting pipeline (resulting in lower friction) and is reduced port if the hole of the valve is one pipe size smaller than the pipe, resulting in less flow through the valve than through the shaft of the pipe. Ball valves may have a handle or lever that aligns with the ball’s position (open or closed) for manual operation. They are primarily used in air, gas, liquid, and steam applications. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 75-100 Series Bronze Ball Valve with Automatic Drain, Two Piece, Inline, Lockable Lever, 3/8 NPT Female
Apollo Valve Apollo 75-100 Series Bronze Ball Valve with Automatic Drain, Two Piece, Inline, Lockable Lever, 3/8 NPT Female"
₱ 1,855.00
Galleon
The Apollo 75-100 series two-piece inline ball valve with automatic drain is made of bronze and has a lockable lever handle and female National Pipe Taper (NPT) threaded connections on both ends. This valve is made of bronze for higher strength and corrosion resistance than brass. This valve is primarily for use in pneumatic applications it has an automatic drain for releasing air pressure from the pneumatic system to which it is connected. When the valve is in the "on" position, the drain vent is closed when the valve is in the "off" position, air from the downstream system is vented to the atmosphere. This valve has a zinc-plated steel, lockable lever handle that can be locked in either the open or closed position using a portable lock (not included). The pounds per square inch (gauge) (psig) rating for this valve is 600 for water, oil, and gas (WOG) and 150 for saturated steam. It is inline for connecting two pipes going in the same direction and has NPT threads on both ends for creating tighter seals than straight threads. Reinforced polytetrafluoroethylene (RPTFE) seats and multifill polytetrafluoroethylene (MPTFE) stem packing reduce the risk of valve leakage. This ball valve is standard (or regular) port for reduced valve size and cost and has a working temperature range of -20 to 450 degrees Fahrenheit. This valve is for use in water and air applications only and meets standard MSS SP-110 for quality assurance. Ball valves use a spherical disc to control the flow between pipes, tubes, or hoses. Flow is allowed when the hole that pierces the ball-shaped disc is in line with the inlet and outlet of the valve. Flow is blocked when the ball is horizontally swiveled 90 degrees, so that the hole of the ball is perpendicular to the opening of the valve. Ball valves can be referred to as full port or reduced port (also known as regular or standard port) depending on the inner diameter of the valve. A ball valve is full port if the hole of the ball is the same size as the inner diameter of the connecting pipeline (resulting in lower friction) and is reduced port if the hole of the valve is one pipe size smaller than the pipe, resulting in less flow through the valve than through the shaft of the pipe. Ball valves may have a handle or lever that aligns with the ball’s position (open or closed) for manual operation. They are primarily used in air, gas, liquid, and steam applications. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 161T-LF Series Bronze Swing Check Valve, Potable Water Service, Class 125, Bronze Seat, 1 NPT Female
Apollo Valve Apollo 161T-LF Series Bronze Swing Check Valve, Potable Water Service, Class 125, Bronze Seat, 1 NPT Female"
₱ 1,261.00
Galleon
This class 125 Apollo 161T-LF series swing check valve is a lead-free y-pattern check valve, and can be installed in both horizontal and vertical line with upward flow. The valve body and seat are made of bronze for higher resistance to corrosion than brass, and are resistant to dezincification. It has female NPT threads for connecting to male threaded pipes, creating a tighter seal than straight threads. The maximum cold working pressure (CWP) is 200 pounds per square inch (psi) at 100 degrees Fahrenheit. The working temperature range is -20 to 406 degrees Fahrenheit. This valve meets standards Manufacturers Standardization Society (MSS) SP139, National Sanitation Foundation (NSF)/American National Standards Institute (ANSI) 61-8 Annex F and G, and American Society of Mechanical Engineers (ASME) B1.20.1 for quality assurance. Check valves have two ports and restrict the flow of fluids and other loose materials through a pipe or passageway to one direction. Flow enters through one port and exits through the other, closing when flow reverses or stops. Two common types of check valves are ball cone valves and swing check valves. A ball cone valve utilizes a spring-loaded ball seated against a cone-shaped interior surface to stop the flow of fluid in a forward direction, and a swing check valve has a movable disc on a hinge to block reverse flow. Check valves are rated by their cracking pressure (the minimum upstream pressure required for the valve to operate), and they are used in various water, gas, air, and steam lines. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 76-500 Series Stainless Steel Ball Valve, Two Piece, Inline, Spring Return Lever, 1/2 NPT Female
Apollo Valve Apollo 76-500 Series Stainless Steel Ball Valve, Two Piece, Inline, Spring Return Lever, 1/2 NPT Female"
₱ 10,008.00
Galleon
The Apollo 76-500 series two-piece inline ball valve is made of stainless steel and has a spring-return lever handle and female National Pipe Taper (NPT) threaded connections on both ends. This valve is made of stainless steel for resistance to corrosion and has a stainless steel spring-return handle with a vinyl sleeve for manual on/off control. This valve closes automatically when its spring-return lever is released, ensuring that the valve is open only when an operator is at hand. The maximum pressure is 2,000 pounds per square inch (gauge) (psig) for water, oil, and gas (WOG) for 1/4” to 1” valves, 1,500 psig for 1-1/4” to 2” valves, and 150 psig for all sizes for saturated steam. The valve is inline for connecting two pipes going in the same direction and has NPT threads on both ends for creating tighter seals than straight threads. Multifill polytetrafluoroethylene (MPTFE) reinforced seats and stem packing reduce the risk of valve leakage and this ball valve is standard (or reduced or regular) port for reduced valve size and cost. This valve is for use with water lines, processing plants, and agricultural applications and meets standard MSS SP-110 for quality assurance. Ball valves use a spherical disc to control the flow between pipes, tubes, or hoses. Flow is allowed when the hole that pierces the ball-shaped disc is in line with the inlet and outlet of the valve. Flow is blocked when the ball is horizontally swiveled 90 degrees, so that the hole of the ball is perpendicular to the opening of the valve. Ball valves can be referred to as full port or reduced port (also known as regular or standard port) depending on the inner diameter of the valve. A ball valve is full port if the hole of the ball is the same size as the inner diameter of the connecting pipeline (resulting in lower friction) and is reduced port if the hole of the valve is one pipe size smaller than the pipe, resulting in less flow through the valve than through the shaft of the pipe. Ball valves may have a handle or lever that aligns with the ball’s position (open or closed) for manual operation. They are primarily used in air, gas, liquid, and steam applications. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 76-500 Series Stainless Steel Ball Valve, Two Piece, Inline, Spring Return Lever, 1 NPT Female
Apollo Valve Apollo 76-500 Series Stainless Steel Ball Valve, Two Piece, Inline, Spring Return Lever, 1 NPT Female"
₱ 13,720.00
Galleon
The Apollo 76-500 series two-piece inline ball valve is made of stainless steel and has a spring-return lever handle and female National Pipe Taper (NPT) threaded connections on both ends. This valve is made of stainless steel for resistance to corrosion and has a stainless steel spring-return handle with a vinyl sleeve for manual on/off control. This valve closes automatically when its spring-return lever is released, ensuring that the valve is open only when an operator is at hand. The maximum pressure is 2,000 pounds per square inch (gauge) (psig) for water, oil, and gas (WOG) for 1/4” to 1” valves, 1,500 psig for 1-1/4” to 2” valves, and 150 psig for all sizes for saturated steam. The valve is inline for connecting two pipes going in the same direction and has NPT threads on both ends for creating tighter seals than straight threads. Multifill polytetrafluoroethylene (MPTFE) reinforced seats and stem packing reduce the risk of valve leakage and this ball valve is standard (or reduced or regular) port for reduced valve size and cost. This valve is for use with water lines, processing plants, and agricultural applications and meets standard MSS SP-110 for quality assurance. Ball valves use a spherical disc to control the flow between pipes, tubes, or hoses. Flow is allowed when the hole that pierces the ball-shaped disc is in line with the inlet and outlet of the valve. Flow is blocked when the ball is horizontally swiveled 90 degrees, so that the hole of the ball is perpendicular to the opening of the valve. Ball valves can be referred to as full port or reduced port (also known as regular or standard port) depending on the inner diameter of the valve. A ball valve is full port if the hole of the ball is the same size as the inner diameter of the connecting pipeline (resulting in lower friction) and is reduced port if the hole of the valve is one pipe size smaller than the pipe, resulting in less flow through the valve than through the shaft of the pipe. Ball valves may have a handle or lever that aligns with the ball’s position (open or closed) for manual operation. They are primarily used in air, gas, liquid, and steam applications. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 71-500 Series Bronze Ball Valve, Two Piece, Inline, Spring-Close Lever, 2 NPT Female
Apollo Valve Apollo 71-500 Series Bronze Ball Valve, Two Piece, Inline, Spring-Close Lever, 2 NPT Female"
₱ 16,252.00
Galleon
The Apollo 71-500 series two-piece inline ball valve is made of bronze and has a spring-close lever handle and female National Pipe Taper (NPT) threaded connections on both ends. This valve is made of bronze for higher strength and corrosion resistance than brass and has a stainless steel spring-close handle with a vinyl sleeve for manual on/off control. This valve closes automatically when its spring-close lever is released, ensuring that the valve is only open when an operator is at hand. The maximum pressure is 600 pounds per square inch (gauge) (psig) for use with water, oil, and gas (WOG) and 150 for saturated steam. The valve is inline for connecting two pipes going in the same direction and has NPT threads on both ends for creating tighter seals than straight threads. Multifill polytetrafluoroethylene (mPTFE) seats and a PTFE seal reduce the risk of valve leakage. This ball valve is standard (or regular) port for reduced valve size and cost. This valve is for use in water lines, processing plants, and agricultural applications and meets standard MSS SP-110 for quality assurance. Ball valves use a spherical disc to control the flow between pipes, tubes, or hoses. Flow is allowed when the hole that pierces the ball-shaped disc is in line with the inlet and outlet of the valve. Flow is blocked when the ball is horizontally swiveled 90 degrees, so that the hole of the ball is perpendicular to the opening of the valve. Ball valves can be referred to as full port or reduced port (also known as regular or standard port) depending on the inner diameter of the valve. A ball valve is full port if the hole of the ball is the same size as the inner diameter of the connecting pipeline (resulting in lower friction) and is reduced port if the hole of the valve is one pipe size smaller than the pipe, resulting in less flow through the valve than through the shaft of the pipe. Ball valves may have a handle or lever that aligns with the ball’s position (open or closed) for manual operation. They are primarily used in air, gas, liquid, and steam applications. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 62-101-01 Stainless Steel Check Valve, Ball Cone, 1/4 NPT Female
Apollo Valve Apollo 62-101-01 Stainless Steel Check Valve, Ball Cone, 1/4 NPT Female"
₱ 3,489.00
Galleon
The Apollo 62-100 series stainless steel ball cone check valve with female National Pipe Taper (NPT) threads on both ends is a class 125 valve used for restricting flow to one direction. It has a spring-loaded ball check cone made of reinforced polytetrafluoroethylene (RPTFE) for fast seating action that is center-guided so that radial alignment is not needed, and it sits against the seat of the valve to block reverse flow. The straight-through flow minimizes velocity change. This check valve's body is made of American Society of Testing and Materials (ASTM) A-351 cast stainless steel for longer life in corrosive environments. This valve has maximum pressure ratings of 400 pounds per square inch (gauge) (psig) for cold working pressure (CWP)and 125 psig for steam working pressure (SWP), and a cracking pressure of 0.5 psi. It has female NPT threads on both ends for connecting to male threaded pipes with tighter seals than straight threads. This class 125 check valve is suited for applications in corrosive environments, including chemical processing, pulp, paper, and other process industries, and meets standard Manufacturers Standardization Society (MSS) SP-80 for quality assurance. Class is a standard relating to tolerance, construction, dimension, and wall thickness, but it is not a direct measurement of maximum working pressure. Check valves have two ports and restrict the flow of fluids and other loose materials through a pipe or passageway to one direction. Flow enters through one port and exits through the other, closing when flow reverses or stops. Two common types of check valves are ball cone valves and swing check valves. A ball cone valve utilizes a spring-loaded ball seated against a cone-shaped interior surface to stop the flow of fluid in a forward direction, and a swing check valve has a movable disc on a hinge to block reverse flow. Check valves are rated by their cracking pressure (the minimum upstream pressure required for the valve to operate), and they are used in various water, gas, air, and steam lines. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 76F-100-A Series Stainless Steel Ball Valve, Two Piece, Inline, Lever, 1-1/4 NPT Female
Apollo Valve Apollo 76F-100-A Series Stainless Steel Ball Valve, Two Piece, Inline, Lever, 1-1/4 NPT Female"
₱ 5,563.00
Galleon
The Apollo 76F-100-A series two-piece full port inline ball valve is made of stainless steel and has a lever handle and female National Pipe Taper (NPT) threaded connections on both ends. This valve is made of stainless steel for resistance to corrosion and has a stainless steel lever handle with vinyl sleeve for manual on/off control. The ball valve is full port for reduced friction its inner diameter is the same as the inner diameter of the pipe it connects to enable maximum operating efficiency. The maximum pressure is 1,000 pounds per square inch (gauge) (psig) for cold working pressure (CWP) and 150 psig for saturated steam, and the temperature range is -20 to 450 degrees Fahrenheit. The valve is inline for connecting two pipes going in the same direction and has NPT threads on both ends for creating tighter seals than straight threads. Reinforced polytetrafluoroethylene (RPTFE) seats and seals reduce the risk of valve leakage. This valve is for use with water lines, processing plants, and agricultural applications and meets standard MSS SP-110 for quality assurance. Ball valves use a spherical disc to control the flow between pipes, tubes, or hoses. Flow is allowed when the hole that pierces the ball-shaped disc is in line with the inlet and outlet of the valve. Flow is blocked when the ball is horizontally swiveled 90 degrees, so that the hole of the ball is perpendicular to the opening of the valve. Ball valves can be referred to as full port or reduced port (also known as regular or standard port) depending on the inner diameter of the valve. A ball valve is full port if the hole of the ball is the same size as the inner diameter of the connecting pipeline (resulting in lower friction) and is reduced port if the hole of the valve is one pipe size smaller than the pipe, resulting in less flow through the valve than through the shaft of the pipe. Ball valves may have a handle or lever that aligns with the ball’s position (open or closed) for manual operation. They are primarily used in air, gas, liquid, and steam applications. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 71-500 Series Bronze Ball Valve, Two Piece, Inline, Spring-Close Lever, 1 NPT Female
Apollo Valve Apollo 71-500 Series Bronze Ball Valve, Two Piece, Inline, Spring-Close Lever, 1 NPT Female"
₱ 8,385.00
Galleon
The Apollo 71-500 series two-piece inline ball valve is made of bronze and has a spring-close lever handle and female National Pipe Taper (NPT) threaded connections on both ends. This valve is made of bronze for higher strength and corrosion resistance than brass and has a stainless steel spring-close handle with a vinyl sleeve for manual on/off control. This valve closes automatically when its spring-close lever is released, ensuring that the valve is only open when an operator is at hand. The maximum pressure is 600 pounds per square inch (gauge) (psig) for use with water, oil, and gas (WOG) and 150 for saturated steam. The valve is inline for connecting two pipes going in the same direction and has NPT threads on both ends for creating tighter seals than straight threads. Multifill polytetrafluoroethylene (mPTFE) seats and a PTFE seal reduce the risk of valve leakage. This ball valve is standard (or regular) port for reduced valve size and cost. This valve is for use in water lines, processing plants, and agricultural applications and meets standard MSS SP-110 for quality assurance. Ball valves use a spherical disc to control the flow between pipes, tubes, or hoses. Flow is allowed when the hole that pierces the ball-shaped disc is in line with the inlet and outlet of the valve. Flow is blocked when the ball is horizontally swiveled 90 degrees, so that the hole of the ball is perpendicular to the opening of the valve. Ball valves can be referred to as full port or reduced port (also known as regular or standard port) depending on the inner diameter of the valve. A ball valve is full port if the hole of the ball is the same size as the inner diameter of the connecting pipeline (resulting in lower friction) and is reduced port if the hole of the valve is one pipe size smaller than the pipe, resulting in less flow through the valve than through the shaft of the pipe. Ball valves may have a handle or lever that aligns with the ball’s position (open or closed) for manual operation. They are primarily used in air, gas, liquid, and steam applications. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 64-100 Series Brass Ball Valve, Two Piece, Inline, Lever, 1-1/4 NPT Female
Apollo Valve Apollo 64-100 Series Brass Ball Valve, Two Piece, Inline, Lever, 1-1/4 NPT Female"
₱ 1,983.00
Galleon
The Apollo 64-100 series two-piece full port ball valve is made of brass and has a lever handle and female National Pipe Taper (NPT) threaded connections on both ends. This valve is made of brass for higher corrosion resistance than steel and has a zinc-plated steel lever handle with a vinyl sleeve for manual on/off control. The ball valve is full port for reduced friction its inner diameter is the same as the inner diameter of the pipe it connects to enable maximum operating efficiency. The maximum pressure is 600 pounds per square inch (psi) for cold water pressure (CWP) and the maximum temperature is 366 degrees Fahrenheit. The valve is inline for connecting two pipes going in the same direction and has NPT threads on both ends for creating tighter seals than straight threads. Polytetrafluoroethylene (PTFE) seats reduce the risk of valve leakage. This valve is for use with water lines, processing plants, and agricultural applications and meets standards MSS SP-110 and ANSI/NSF 61 for quality assurance. Ball valves use a spherical disc to control the flow between pipes, tubes, or hoses. Flow is allowed when the hole that pierces the ball-shaped disc is in line with the inlet and outlet of the valve. Flow is blocked when the ball is horizontally swiveled 90 degrees, so that the hole of the ball is perpendicular to the opening of the valve. Ball valves can be referred to as full port or reduced port (also known as regular or standard port) depending on the inner diameter of the valve. A ball valve is full port if the hole of the ball is the same size as the inner diameter of the connecting pipeline (resulting in lower friction) and is reduced port if the hole of the valve is one pipe size smaller than the pipe, resulting in less flow through the valve than through the shaft of the pipe. Ball valves may have a handle or lever that aligns with the ball’s position (open or closed) for manual operation. They are primarily used in air, gas, liquid, and steam applications. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 161T-LF Series Bronze Swing Check Valve, Potable Water Service, Class 125, Bronze Seat, 3/8 NPT Female
Apollo Valve Apollo 161T-LF Series Bronze Swing Check Valve, Potable Water Service, Class 125, Bronze Seat, 3/8 NPT Female"
₱ 3,207.00
Galleon
This class 125 Apollo 161T-LF series swing check valve is a lead-free y-pattern check valve, and can be installed in both horizontal and vertical line with upward flow. The valve body and seat are made of bronze for higher resistance to corrosion than brass, and are resistant to dezincification. It has female NPT threads for connecting to male threaded pipes, creating a tighter seal than straight threads. The maximum cold working pressure (CWP) is 200 pounds per square inch (psi) at 100 degrees Fahrenheit. The working temperature range is -20 to 406 degrees Fahrenheit. This valve meets standards Manufacturers Standardization Society (MSS) SP139, National Sanitation Foundation (NSF)/American National Standards Institute (ANSI) 61-8 Annex F and G, and American Society of Mechanical Engineers (ASME) B1.20.1 for quality assurance. Check valves have two ports and restrict the flow of fluids and other loose materials through a pipe or passageway to one direction. Flow enters through one port and exits through the other, closing when flow reverses or stops. Two common types of check valves are ball cone valves and swing check valves. A ball cone valve utilizes a spring-loaded ball seated against a cone-shaped interior surface to stop the flow of fluid in a forward direction, and a swing check valve has a movable disc on a hinge to block reverse flow. Check valves are rated by their cracking pressure (the minimum upstream pressure required for the valve to operate), and they are used in various water, gas, air, and steam lines. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 70-600 Series Bronze Ball Valve, Two Piece, 3-Port Diverting, Lever, 1/2 NPT Female
Apollo Valve Apollo 70-600 Series Bronze Ball Valve, Two Piece, 3-Port Diverting, Lever, 1/2 NPT Female"
₱ 1,642.00
Galleon
The Apollo 70-600 series two-piece three-port diverting ball valve is made of bronze and has a lever handle and female National Pipe Taper (NPT) threaded connections on both ends. This valve is made of bronze for higher strength and corrosion resistance than brass and has a zinc-plated steel lever handle with a vinyl sleeve for manual control. This ball valve is three-port diverting to regulate flow among three sections of pipe. Its maximum pressure is 400 pounds per square inch (gauge) (psig) for use with water, oil, and gas (WOG). It has NPT threads on both ends for creating tighter seals than straight threads. Reinforced polytetrafluoroethylene (RPTFE) seats and a PTFE seal reduce the risk of valve leakage. This ball valve is standard (or regular) port for reduced valve size and cost and has a working temperature range of -20 to 450 degrees Fahrenheit. This valve is for use in water lines, processing plants, and agricultural applications and meets standard MSS SP-110 for quality assurance. Ball valves use a spherical disc to control the flow between pipes, tubes, or hoses. Flow is allowed when the hole that pierces the ball-shaped disc is in line with the inlet and outlet of the valve. Flow is blocked when the ball is horizontally swiveled 90 degrees, so that the hole of the ball is perpendicular to the opening of the valve. Ball valves can be referred to as full port or reduced port (also known as regular or standard port) depending on the inner diameter of the valve. A ball valve is full port if the hole of the ball is the same size as the inner diameter of the connecting pipeline (resulting in lower friction) and is reduced port if the hole of the valve is one pipe size smaller than the pipe, resulting in less flow through the valve than through the shaft of the pipe. Ball valves may have a handle or lever that aligns with the ball’s position (open or closed) for manual operation. They are primarily used in air, gas, liquid, and steam applications. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 70-100 Series Bronze Ball Valve, Two Piece, Inline, Lever, 1 NPT Female
Apollo Valve Apollo 70-100 Series Bronze Ball Valve, Two Piece, Inline, Lever, 1 NPT Female"
₱ 1,814.00
Galleon
The Apollo 70-100 series two-piece inline ball valve is made of bronze and has a lever handle and female National Pipe Taper (NPT) threaded connections on both ends. This valve is made of bronze for higher strength and corrosion resistance than brass and has a zinc-plated steel lever handle with a vinyl sleeve for manual on/off control. The maximum pressure is 600 pounds per square inch (gauge) (psig) for use with water, oil, and gas (WOG) and 150 for saturated steam. The valve is inline for connecting two pipes going in the same direction and has NPT threads on both ends for creating tighter seals than straight threads. Polytetrafluoroethylene (PTFE) reinforced seats and seals reduce the risk of valve leakage. This ball valve is standard (or reduced or regular) port for reduced valve size and cost and has a working temperature range of 0 - 500 degrees Fahrenheit. This valve is for use in water lines, processing plants, and agricultural applications and meets standard MSS SP-110 for quality assurance. Ball valves use a spherical disc to control the flow between pipes, tubes, or hoses. Flow is allowed when the hole that pierces the ball-shaped disc is in line with the inlet and outlet of the valve. Flow is blocked when the ball is horizontally swiveled 90 degrees, so that the hole of the ball is perpendicular to the opening of the valve. Ball valves can be referred to as full port or reduced port (also known as regular or standard port) depending on the inner diameter of the valve. A ball valve is full port if the hole of the ball is the same size as the inner diameter of the connecting pipeline (resulting in lower friction) and is reduced port if the hole of the valve is one pipe size smaller than the pipe, resulting in less flow through the valve than through the shaft of the pipe. Ball valves may have a handle or lever that aligns with the ball’s position (open or closed) for manual operation. They are primarily used in air, gas, liquid, and steam applications. Conbraco Industries, Inc. manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices under the Apollo Valves brand. The company, founded in 1928 and headquartered in Matthews, NC, meets international standard ISO/IEC 17025:2005 and makes products that meet International Organization for Standardization (ISO) and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 4N3A55A Bronze Dual Check Valve, 1 NPT Female
Apollo Valve Apollo 4N3A55A Bronze Dual Check Valve, 1 NPT Female"
₱ 3,432.00
Galleon
The Apollo DUC-4N Series Dual Check Valve Backflow Preventer is designed to prevent cross connections of non potable water (non-hazardous) into safe drinking water systems. It is a compact and economical device that consists of two independently-acting, spring-loaded check valves in a corrosion-resistant material. Each of the two spring-loaded check valves is designed to open at 1 psi differential in the direction of flow. The check valves will remain tightly closed until there is a demand for water downstream. If the downstream pressure of the device increases above the supply pressure or there is a reverse direction of flow, the check valves will close to prevent backflow. If the second check valve is prevented from closing tightly, the first check will close to provide protection from a backflow condition. Replaceable check modules. Industry lay lengths. Maximum Working pressure 175 psi. 33/180 degrees F Operating temperature range. ASSE1024 and CSA approved. Cast Bronze C84400 body. Brass union tailpiece and union nut. Glass-Filled PPO/Acetal check modules. Stainless steel spring. Buna-N Seat Discs.
Read more
Go to Shop
Apollo Valve Apollo 161T-LF Series Bronze Swing Check Valve, Potable Water Service, Class 125, Bronze Seat, 1/2 NPT Female
Apollo Valve Apollo 161T-LF Series Bronze Swing Check Valve, Potable Water Service, Class 125, Bronze Seat, 1/2 NPT Female"
₱ 871.00
Galleon
This class 125 Apollo 161T-LF series swing check valve is a lead-free y-pattern check valve, and can be installed in both horizontal and vertical line with upward flow. The valve body and seat are made of bronze for higher resistance to corrosion than brass, and are resistant to dezincification. It has female NPT threads for connecting to male threaded pipes, creating a tighter seal than straight threads. The maximum cold working pressure (CWP) is 200 pounds per square inch (psi) at 100 degrees Fahrenheit. The working temperature range is -20 to 406 degrees Fahrenheit. This valve meets standards Manufacturers Standardization Society (MSS) SP139, National Sanitation Foundation (NSF)/American National Standards Institute (ANSI) 61-8 Annex F and G, and American Society of Mechanical Engineers (ASME) B1.20.1 for quality assurance. Check valves have two ports and restrict the flow of fluids and other loose materials through a pipe or passageway to one direction. Flow enters through one port and exits through the other, closing when flow reverses or stops. Two common types of check valves are ball cone valves and swing check valves. A ball cone valve utilizes a spring-loaded ball seated against a cone-shaped interior surface to stop the flow of fluid in a forward direction, and a swing check valve has a movable disc on a hinge to block reverse flow. Check valves are rated by their cracking pressure (the minimum upstream pressure required for the valve to operate), and they are used in various water, gas, air, and steam lines. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 161T-LF Series Bronze Swing Check Valve, Potable Water Service, Class 125, Bronze Seat, 2 NPT Female
Apollo Valve Apollo 161T-LF Series Bronze Swing Check Valve, Potable Water Service, Class 125, Bronze Seat, 2 NPT Female"
₱ 14,182.00
Galleon
This class 125 Apollo 161T-LF series swing check valve is a lead-free y-pattern check valve, and can be installed in both horizontal and vertical line with upward flow. The valve body and seat are made of bronze for higher resistance to corrosion than brass, and are resistant to dezincification. It has female NPT threads for connecting to male threaded pipes, creating a tighter seal than straight threads. The maximum cold working pressure (CWP) is 200 pounds per square inch (psi) at 100 degrees Fahrenheit. The working temperature range is -20 to 406 degrees Fahrenheit. This valve meets standards Manufacturers Standardization Society (MSS) SP139, National Sanitation Foundation (NSF)/American National Standards Institute (ANSI) 61-8 Annex F and G, and American Society of Mechanical Engineers (ASME) B1.20.1 for quality assurance. Check valves have two ports and restrict the flow of fluids and other loose materials through a pipe or passageway to one direction. Flow enters through one port and exits through the other, closing when flow reverses or stops. Two common types of check valves are ball cone valves and swing check valves. A ball cone valve utilizes a spring-loaded ball seated against a cone-shaped interior surface to stop the flow of fluid in a forward direction, and a swing check valve has a movable disc on a hinge to block reverse flow. Check valves are rated by their cracking pressure (the minimum upstream pressure required for the valve to operate), and they are used in various water, gas, air, and steam lines. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 32-100 Series Bronze Ball Valve, Two Piece, Inline, Lever, 1-1/2 NPT Female
Apollo Valve Apollo 32-100 Series Bronze Ball Valve, Two Piece, Inline, Lever, 1-1/2 NPT Female"
₱ 2,596.00
Galleon
The Apollo 32-100 series two-piece inline ball valve is made of bronze and has a lever handle and female National Pipe Taper (NPT) threaded connections on both ends. This valve is made of bronze for higher strength and corrosion resistance than brass. It has a zinc-plated steel lever handle with a vinyl sleeve for manual on/off control. This ball valve is standard (or regular) port for reduced valve size and cost. The maximum pressure is 400 pounds per square inch (psi) for cold working pressure (CWP) and 125 psi for steam working pressure (SWP), and the maximum temperature is 400 degrees Fahrenheit. The valve is inline for connecting two pipes going in the same direction and has NPT threads on both ends for creating tighter seals than straight threads. Polytetrafluoroethylene (PTFE) seats and reinforced polytetraflouroethylene (RPTFE) stem packing reduce the risk of valve leakage. This valve is for use in water lines, processing plants, and agricultural applications and meets standards MSS SP-110 and CRN: OC10908.5 for quality assurance. Ball valves use a spherical disc to control the flow between pipes, tubes, or hoses. Flow is allowed when the hole that pierces the ball-shaped disc is in line with the inlet and outlet of the valve. Flow is blocked when the ball is horizontally swiveled 90 degrees, so that the hole of the ball is perpendicular to the opening of the valve. Ball valves can be referred to as full port or reduced port (also known as regular or standard port) depending on the inner diameter of the valve. A ball valve is full port if the hole of the ball is the same size as the inner diameter of the connecting pipeline (resulting in lower friction) and is reduced port if the hole of the valve is one pipe size smaller than the pipe, resulting in less flow through the valve than through the shaft of the pipe. Ball valves may have a handle or lever that aligns with the ball’s position (open or closed) for manual operation. They are primarily used in air, gas, liquid, and steam applications. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 121T-LF Series Bronze Globe Valve, Potable Water Service, Class 125, Inline, Threaded Bonnet, 3/4 NPT Female
Apollo Valve Apollo 121T-LF Series Bronze Globe Valve, Potable Water Service, Class 125, Inline, Threaded Bonnet, 3/4 NPT Female"
₱ 5,480.00
Galleon
This class 125 Apollo 121T-LF series inline bronze globe valve has a threaded bonnet, lead-free construction for use with potable water, rising stem, bronze seat, and female National Pipe Taper (NPT) threads on both ends, and is used to control flow (throttling) in a pipeline or water plumbing system. The valve body and seat are constructed of American Society for Testing and Material (ASTM) B62 bronze for strength and corrosion resistance. The valve’s maximum pressure is 200 pounds per square inch (gauge) (psig) for cold working pressure (CWP) and 125 psig for steam working pressure (SWP). It has a threaded bonnet for tight assembly and reduced risk of leakage, and female NPT threads on both ends for connecting to male threaded pipes. This class 125 valve meets standard Manufacturers Standardization Society (MSS) SP-80 for quality assurance and complies with California Assembly Bill AB1953, Vermont Act 193, Maryland HB372, Louisiana HB471 and federal public law 111- S3874, which limit the amount of lead in plumbing fixtures that come in contact with water intended for human consumption. Class is a standard relating to tolerance, construction, dimension, and wall thickness, but it is not a direct measurement of maximum working pressure. This rising stem globe valve is for use in various pipeline or water plumbing systems. Globe valves control flow rates in a piping system by the lift of a vertical stem and disk, which must be turned to open and close the valve. A seated disc extends into the center of the valve to act as a plug to restrict or open the flow path, depending on how tightly the valve stem is turned. The stem on globe valves can be either rising (moves up as the valve opens) to indicate if the flow is on or off, or non-rising (stem height remains constant when the valve is either open or closed) for use in small spaces. Globe valves are used in various water, gas, air, and steam piping systems that require frequent throttling operations. Conbraco Industries, Inc. manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices under the Apollo Valve brand. The company, founded in 1928 and headquartered in Matthews, NC, meets international standard ISO/IEC 17025:2005 and makes products that meet International Organization for Standardization (ISO) and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve YCT Series Cast Iron Y-Strainer, 2 NPT Female, 20 Mesh Screen
Apollo Valve YCT Series Cast Iron Y-Strainer, 2 NPT Female, 20 Mesh Screen"
₱ 7,132.00
Galleon
YCT Strainers are designed to protect piping systems and process equipment from unwanted foreign particles with minimum pressure loss. Install these hardworking strainers upstream in almost any application to protect valves, regulators, solenoids and meters from rust, dirt and pipe scale. Cast Iron, ASTM A126-B for Body, Cap/Cover and Plug. 304 Stainless steel screen. Graphite gasket. Working pressure (non-shock): 250 psig at 406 degree F for Steam 400 psig at 150 degree F for Water, Oil, Gas. CSA B-51 and CRN OE10274.5 approved.
Read more
Go to Shop
Apollo Valve Apollo 3810501 Bronze Atmospheric Type Vacuum Breaker, 1 NPT Female
Apollo Valve Apollo 3810501 Bronze Atmospheric Type Vacuum Breaker, 1 NPT Female"
₱ 4,116.00
Galleon
The Apollo Model AVB1 (38-100) Atmospheric Type Vacuum Breaker is designed to prevent contamination of potable water due to back-siphonage. This vacuum breaker is not designed for backpressure conditions or continuous pressure applications of more than 12 hours in a 24 hours period. This Apollo Model AVB1 is recommended for low flow installations that use small amounts of water. Should only be installed in areas where spillage of water would not cause damage. Silicone seat disc. Polypropylene/polyethylene float. Brass guide. Plated steel/brass canopy. Polypropylene gasket and Buna-N O-Ring.
Read more
Go to Shop
Apollo Valve 10-600 Series Bronze Safety Relief Valve, ASME Hot Water, 150 psi Set Pressure, 3/4 NPT Female
Apollo Valve 10-600 Series Bronze Safety Relief Valve, ASME Hot Water, 150 psi Set Pressure, 3/4 NPT Female"
₱ 5,620.00
Galleon
This Apollo Valve 10-600 series hot water relief valve protects against excessive water pressure due to failure of controls to regulate BTU input. It has a bronze body, a 150 pounds per square inch (psi) relief pressure, and a 3/4" female National Pipe Thread (NPT) inlet connection and 3/4" female NPT outlet. The valve's body and spring cage are bronze for resistance to corrosion. The seat is silicone for resistance to high temperatures and is elevated for draining water away from the seat area. The spring is steel for resistance to corrosion, and a fabric-reinforced, molded EPDM (ethylene propylene diene monomer) diaphragm isolates the spring from water at all times. The valve can be used in operating temperatures up to 250 degrees F. This relief valve is American Society of Mechanical Engineers (ASME) safety rated for Section IV heating boilers and is suitable for hot water heating boilers and hot water supply systems. Relief valves remove excess pressure or vacuum from a system. The valve openings allow fluids or gases to escape to decrease pressure, and then close once the valve reaches the reseating pressure limit. They also relieve excess vacuum by opening to release a gas into the system and then closing after it reaches its low-pressure limit. Some relief valves have an adjustment mechanism to set the pressure where the valve opens, making it suitable for various applications. Relief valves are rated according to the volume of liquid or gas that can flow through them and the material that the valve is constructed from must be suitable for the fluid or gas, which may be corrosive or at an extreme temperature, in which it operates. Relief valves are used in a variety of applications, such as air compressors, petrochemical and chemical manufacturing, natural gas processing, and power generation. Apollo Valves manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention. The company, founded in 1928 and headquartered in Matthews, NC, meets international standard International Organization for Standardization (ISO)/IEC standard 17025:2005.
Read more
Go to Shop
Apollo Valve 59 Series Bronze Y-Strainer with Tapped Cap, 1 NPT Female, 20 Mesh Screen
Apollo Valve 59 Series Bronze Y-Strainer with Tapped Cap, 1 NPT Female, 20 Mesh Screen"
₱ 3,800.00
Galleon
The Apollo YB strainers are designed to protect piping systems and process equipment from unwanted foreign particles with minimum pressure loss. Lightweight, compact protection against foreign particles. Corrosion resistant bronze body and stainless steel screens. 100 percent American made. 100 percent factory pressure tested. Removable self-aligning screen. Operating pressures to 400 psig. Working pressure: 125 psig at 350 degree F steam and 400 psig at 150 degree F water, oil, gas. Body: cast bronze, ASTM B584. Screen: 302 stainless steel. Approvals: CRN 0E8959.5C.
Read more
Go to Shop
Apollo Valve Apollo 102T-LF Series Bronze Gate Valve, Potable Water Service, Class 125, Non-Rising Stem, 1/2 NPT Female
Apollo Valve Apollo 102T-LF Series Bronze Gate Valve, Potable Water Service, Class 125, Non-Rising Stem, 1/2 NPT Female"
₱ 2,323.00
Galleon
This class 125 Apollo Valve 102T-LF series gate valve has a non-rising stem, female National Pipe Taper (NPT) threads, and lead-free bronze construction for potable water plumbing systems. The lead-free bronze construction, solid wedge gate, and threaded bonnet provide higher strength and resistance to corrosion than brass. The valve has a non-rising stem that stays fixed in place when the gate is raised or lowered for low clearance or underground use, and the graphite internal packing helps prevent the valve’s stem from leaking. This gate valve is full port for reduced friction its inner diameter is the same as the inner diameter of the pipe it connects to enable maximum operating efficiency. The maximum pressure is 150 pounds per square inch (gauge) (psig) for cold working pressure (CWP), and it has a temperature range of -20 degrees F to 406 degrees F. It has female NPT threads for use with male threaded pipes. Mounted on top of the valve, a manually operated malleable iron hand wheel activates the inside screw mechanism, which lifts and lowers the gate to start and stop the flow between the connected pipes. This valve comes with a five-year warranty for workmanship and material defects. The valve is certified as containing no more than 0.25 percent lead by weighted average on its wetted surfaces and complies with California AB1953, Vermont Act 193, Maryland HB372, and federal public law 111-380 for use with public drinking water. This class 125 valve meets Manufacturers Standardization Society (MSS) SP-139 and National Sanitation Foundation/American National Standards Institute (NSF/ANSI) 61-8, Annexes F and G standards for quality assurance. Class is a standard relating to tolerance, construction, dimension, and wall thickness, but it is not a direct measurement of maximum working pressure. The valve is appropriate for use in plumbing systems that convey or dispense water intended for cooking or human consumption. Gate valves control flow in a piping system by lifting a gate out of the path of steam, fluids, or gases. They are designed to block or permit flow, as the vibrations and force of flow repeatedly striking a partly lowered gate can damage the gate and seats. To accommodate different flows and pressure requirements, gates come in four types: solid wedge (appropriate for almost all liquid service), flexible wedge (appropriate for steam service), split wedge (appropriate for normal temperature, non-condensing gas and liquid service, including corrosive service), and parallel disc (appropriate for high and low pressure applications). Hand wheels or levers activate the screw mechanism in the valve’s bonnet, which comes in various designs, to open and close the gate. Union bonnets are preferable for building service piping, threaded-in (or screw-in) bonnets work well for lighter-duty usage, and bolted body-bonnet connections are used primarily in iron multi-turn valves. Most gate valves have either a rising stem, which moves up and down with the gate, or a non-rising stem, which remains fixed in place. When closed, the gate and its seats form tight planar sealing surfaces, ideal for linear liquid flow. Gate valves are used in air, gas, liquid, and steam applications. Conbraco Industries, Inc. manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices under the Apollo Valves brand. The company, founded in 1928 and headquartered in Matthews, NC, meets international standard ISO/IEC 17025:2005 and makes products that meet International Organization for Standardization (ISO) and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve 10-600 Series Bronze Safety Relief Valve, ASME Hot Water, 100 psi Set Pressure, 1 NPT Female
Apollo Valve 10-600 Series Bronze Safety Relief Valve, ASME Hot Water, 100 psi Set Pressure, 1 NPT Female"
₱ 8,746.00
Galleon
This Apollo Valve 10-600 series hot water relief valve protects against excessive water pressure due to failure of controls to regulate BTU input. It has a bronze body, a 100 pounds per square inch (psi) relief pressure, and a 1" female National Pipe Thread (NPT) inlet connection and 1" female NPT outlet. The valve's body and spring cage are bronze for resistance to corrosion. The seat is silicone for resistance to high temperatures and is elevated for draining water away from the seat area. The spring is steel for resistance to corrosion, and a fabric-reinforced, molded EPDM (ethylene propylene diene monomer) diaphragm isolates the spring from water at all times. The valve can be used in operating temperatures up to 250 degrees F. This relief valve is American Society of Mechanical Engineers (ASME) safety rated for Section IV heating boilers and is suitable for hot water heating boilers and hot water supply systems. Relief valves remove excess pressure or vacuum from a system. The valve openings allow fluids or gases to escape to decrease pressure, and then close once the valve reaches the reseating pressure limit. They also relieve excess vacuum by opening to release a gas into the system and then closing after it reaches its low-pressure limit. Some relief valves have an adjustment mechanism to set the pressure where the valve opens, making it suitable for various applications. Relief valves are rated according to the volume of liquid or gas that can flow through them and the material that the valve is constructed from must be suitable for the fluid or gas, which may be corrosive or at an extreme temperature, in which it operates. Relief valves are used in a variety of applications, such as air compressors, petrochemical and chemical manufacturing, natural gas processing, and power generation. Apollo Valves manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention. The company, founded in 1928 and headquartered in Matthews, NC, meets international standard International Organization for Standardization (ISO)/IEC standard 17025:2005.
Read more
Go to Shop
Apollo Valve 10-600 Series Bronze Safety Relief Valve, ASME Hot Water, 100 psi Set Pressure, 3/4 NPT Female
Apollo Valve 10-600 Series Bronze Safety Relief Valve, ASME Hot Water, 100 psi Set Pressure, 3/4 NPT Female"
₱ 4,160.00
Galleon
This Apollo Valve 10-600 series hot water relief valve protects against excessive water pressure due to failure of controls to regulate BTU input. It has a bronze body, a 100 pounds per square inch (psi) relief pressure, and a 3/4" female National Pipe Thread (NPT) inlet connection and 3/4" female NPT outlet. The valve's body and spring cage are bronze for resistance to corrosion. The seat is silicone for resistance to high temperatures and is elevated for draining water away from the seat area. The spring is steel for resistance to corrosion, and a fabric-reinforced, molded EPDM (ethylene propylene diene monomer) diaphragm isolates the spring from water at all times. The valve can be used in operating temperatures up to 250 degrees F. This relief valve is American Society of Mechanical Engineers (ASME) safety rated for Section IV heating boilers and is suitable for hot water heating boilers and hot water supply systems. Relief valves remove excess pressure or vacuum from a system. The valve openings allow fluids or gases to escape to decrease pressure, and then close once the valve reaches the reseating pressure limit. They also relieve excess vacuum by opening to release a gas into the system and then closing after it reaches its low-pressure limit. Some relief valves have an adjustment mechanism to set the pressure where the valve opens, making it suitable for various applications. Relief valves are rated according to the volume of liquid or gas that can flow through them and the material that the valve is constructed from must be suitable for the fluid or gas, which may be corrosive or at an extreme temperature, in which it operates. Relief valves are used in a variety of applications, such as air compressors, petrochemical and chemical manufacturing, natural gas processing, and power generation. Apollo Valves manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention. The company, founded in 1928 and headquartered in Matthews, NC, meets international standard International Organization for Standardization (ISO)/IEC standard 17025:2005.
Read more
Go to Shop
Apollo Valve Apollo 121T Series Bronze Globe Valve, Class 125, Inline, Threaded Bonnet, Bronze Seat, 2 NPT Female
Apollo Valve Apollo 121T Series Bronze Globe Valve, Class 125, Inline, Threaded Bonnet, Bronze Seat, 2 NPT Female"
₱ 15,150.00
Galleon
This class 125 Apollo 121T series inline bronze globe valve has a threaded bonnet, rising stem, bronze seat, and female National Pipe Taper (NPT) threads on both ends, and is used to control flow (throttling) in a pipeline or water plumbing system. The valve body and seat are constructed of American Society for Testing and Material (ASTM) B62 bronze for strength and corrosion resistance.The valve’s maximum pressure is 200 pounds per square inch (gauge) (psig) for cold working pressure (CWP) and 125 psig for steam working pressure (SWP). It has a threaded bonnet for tight assembly and reduced risk of leakage, and female NPT threads on both ends for connecting to male threaded pipes. This class 125 valve meets standard Manufacturers Standardization Society (MSS) SP-80 for quality assurance. Class is a standard relating to tolerance, construction, dimension, and wall thickness, but it is not a direct measurement of maximum working pressure. This rising stem globe valve is for use in various pipeline or water plumbing systems. Globe valves control flow rates in a piping system by the lift of a vertical stem and disk, which must be turned to open and close the valve. A seated disc extends into the center of the valve to act as a plug to restrict or open the flow path, depending on how tightly the valve stem is turned. The stem on globe valves can be either rising (moves up as the valve opens) to indicate if the flow is on or off, or non-rising (stem height remains constant when the valve is either open or closed) for use in small spaces. Globe valves are used in various water, gas, air, and steam piping systems that require frequent throttling operations. Conbraco Industries, Inc. manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices under the Apollo Valve brand. The company, founded in 1928 and headquartered in Matthews, NC, meets international standard ISO/IEC 17025:2005 and makes products that meet International Organization for Standardization (ISO) and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 121T-LF Series Bronze Globe Valve, Potable Water Service, Class 125, Inline, Threaded Bonnet, 1/2 NPT Female
Apollo Valve Apollo 121T-LF Series Bronze Globe Valve, Potable Water Service, Class 125, Inline, Threaded Bonnet, 1/2 NPT Female"
₱ 3,468.00
Galleon
This class 125 Apollo 121T-LF series inline bronze globe valve has a threaded bonnet, lead-free construction for use with potable water, rising stem, bronze seat, and female National Pipe Taper (NPT) threads on both ends, and is used to control flow (throttling) in a pipeline or water plumbing system. The valve body and seat are constructed of American Society for Testing and Material (ASTM) B62 bronze for strength and corrosion resistance. The valve’s maximum pressure is 200 pounds per square inch (gauge) (psig) for cold working pressure (CWP) and 125 psig for steam working pressure (SWP). It has a threaded bonnet for tight assembly and reduced risk of leakage, and female NPT threads on both ends for connecting to male threaded pipes. This class 125 valve meets standard Manufacturers Standardization Society (MSS) SP-80 for quality assurance and complies with California Assembly Bill AB1953, Vermont Act 193, Maryland HB372, Louisiana HB471 and federal public law 111- S3874, which limit the amount of lead in plumbing fixtures that come in contact with water intended for human consumption. Class is a standard relating to tolerance, construction, dimension, and wall thickness, but it is not a direct measurement of maximum working pressure. This rising stem globe valve is for use in various pipeline or water plumbing systems. Globe valves control flow rates in a piping system by the lift of a vertical stem and disk, which must be turned to open and close the valve. A seated disc extends into the center of the valve to act as a plug to restrict or open the flow path, depending on how tightly the valve stem is turned. The stem on globe valves can be either rising (moves up as the valve opens) to indicate if the flow is on or off, or non-rising (stem height remains constant when the valve is either open or closed) for use in small spaces. Globe valves are used in various water, gas, air, and steam piping systems that require frequent throttling operations. Conbraco Industries, Inc. manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices under the Apollo Valve brand. The company, founded in 1928 and headquartered in Matthews, NC, meets international standard ISO/IEC 17025:2005 and makes products that meet International Organization for Standardization (ISO) and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve 10-400 Series Bronze Safety Relief Valve, ASME Hot Water, 75 psi Set Pressure, 3/4 NPT Female
Apollo Valve 10-400 Series Bronze Safety Relief Valve, ASME Hot Water, 75 psi Set Pressure, 3/4 NPT Female"
₱ 1,651.00
Galleon
This Apollo Valve 10-400 series safety relief valve has a bronze body, a 75 pounds per square inch (psi) relief pressure, a 3/4" female National Pipe Thread (NPT) inlet connection, and a 3/4" female NPT outlet. The valve's body and nozzle are bronze for resistance to corrosion, the seat is silicone for resistance to high temperatures, and the spring is stainless steel for resistance to corrosion. The valve can be used in operating temperatures up to 250 degrees F. This safety valve is American Society of Mechanical Engineers (ASME) safety rated for Section IV hot water heating boilers and hydronic heating systems. Relief valves remove excess pressure or vacuum from a system. The valve openings allow fluids or gases to escape to decrease pressure, and then close once the valve reaches the reseating pressure limit. They also relieve excess vacuum by opening to release a gas into the system and then closing after it reaches its low-pressure limit. Some relief valves have an adjustment mechanism to set the pressure where the valve opens, making it suitable for various applications. Relief valves are rated according to the volume of liquid or gas that can flow through them and the material that the valve is constructed from must be suitable for the fluid or gas, which may be corrosive or at an extreme temperature, in which it operates. Relief valves are used in a variety of applications, such as air compressors, petrochemical and chemical manufacturing, natural gas processing, and power generation. Apollo Valves manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention. The company, founded in 1928 and headquartered in Matthews, NC, meets international standard International Organization for Standardization (ISO)/IEC standard 17025:2005.
Read more
Go to Shop
Apollo Valve 59 Series Bronze Y-Strainer with Tapped Cap, 1/2 NPT Female, 50 Mesh Screen
Apollo Valve 59 Series Bronze Y-Strainer with Tapped Cap, 1/2 NPT Female, 50 Mesh Screen"
₱ 1,521.00
Galleon
The Apollo YB strainers are designed to protect piping systems and process equipment from unwanted foreign particles with minimum pressure loss. Lightweight, compact protection against foreign particles. Corrosion resistant bronze body and stainless steel screens. 100 percent American made. 100 percent factory pressure tested. Removable self-aligning screen. Operating pressures to 400 psig. Working pressure: 125 psig at 350 degree F steam and 400 psig at 150 degree F water, oil, gas. Body: cast bronze, ASTM B584. Screen: 302 stainless steel. Approvals: CRN 0E8959.5C.
Read more
Go to Shop
Apollo Valve 59LF Series Bronze Lead Free Y-Strainer with 3/4 Tapped Cap, 1
Apollo Valve 59LF Series Bronze Lead Free Y-Strainer with 3/4 Tapped Cap, 1" NPT Female, 20 Mesh Screen"
₱ 5,194.00
Galleon
The Apollo Lead Free YB-LF (59LF Series) strainers are designed to protect piping systems and process equipment from unwanted foreign particles with minimum pressure loss. Lightweight, compact protection against foreign particles. Corrosion resistant bronze body and stainless steel screens. 100 percent factory pressure tested. Blowout ball valve option. Lead Free AB 1953 Certified. Made in USA. Operating pressures to 400 psig. Working pressure: 125 psig at 350 degree F steam and 400 psig at 150 degree F water, oil, gas. Body: cast bronze. Screen: 302 stainless steel.
Read more
Go to Shop
Apollo Valve 59LF Series Bronze Lead Free Y-Strainer, 3/4 NPT Female, 20 Mesh Screen
Apollo Valve 59LF Series Bronze Lead Free Y-Strainer, 3/4 NPT Female, 20 Mesh Screen"
₱ 3,544.00
Galleon
The Apollo Lead Free YB-LF (59LF Series) strainers are designed to protect piping systems and process equipment from unwanted foreign particles with minimum pressure loss. Lightweight, compact protection against foreign particles. Corrosion resistant bronze body and stainless steel screens. 100 percent factory pressure tested. Blowout ball valve option. Lead Free AB 1953 Certified. Made in USA. Operating pressures to 400 psig. Working pressure: 125 psig at 350 degree F steam and 400 psig at 150 degree F water, oil, gas. Body: cast bronze. Screen: 302 stainless steel.
Read more
Go to Shop
Apollo Valve 59 Series Bronze Y-Strainer with Tapped Cap, 2 NPT Female, 20 Mesh Screen
Apollo Valve 59 Series Bronze Y-Strainer with Tapped Cap, 2 NPT Female, 20 Mesh Screen"
₱ 8,447.00
Galleon
The Apollo YB strainers are designed to protect piping systems and process equipment from unwanted foreign particles with minimum pressure loss. Lightweight, compact protection against foreign particles. Corrosion resistant bronze body and stainless steel screens. 100 percent American made. 100 percent factory pressure tested. Removable self-aligning screen. Operating pressures to 400 psig. Working pressure: 125 psig at 350 degree F steam and 400 psig at 150 degree F water, oil, gas. Body: cast bronze, ASTM B584. Screen: 302 stainless steel. Approvals: CRN 0E8959.5C.
Read more
Go to Shop
Apollo Valve Apollo 70-600 Series Bronze Ball Valve, Two Piece, 3-Port Diverting, Lever, 3/4 NPT Female
Apollo Valve Apollo 70-600 Series Bronze Ball Valve, Two Piece, 3-Port Diverting, Lever, 3/4 NPT Female"
₱ 2,671.00
Galleon
The Apollo 70-600 series two-piece three-port diverting ball valve is made of bronze and has a lever handle and female National Pipe Taper (NPT) threaded connections on both ends. This valve is made of bronze for higher strength and corrosion resistance than brass and has a zinc-plated steel lever handle with a vinyl sleeve for manual control. This ball valve is three-port diverting to regulate flow among three sections of pipe. Its maximum pressure is 400 pounds per square inch (gauge) (psig) for use with water, oil, and gas (WOG). It has NPT threads on both ends for creating tighter seals than straight threads. Reinforced polytetrafluoroethylene (RPTFE) seats and a PTFE seal reduce the risk of valve leakage. This ball valve is standard (or regular) port for reduced valve size and cost and has a working temperature range of -20 to 450 degrees Fahrenheit. This valve is for use in water lines, processing plants, and agricultural applications and meets standard MSS SP-110 for quality assurance. Ball valves use a spherical disc to control the flow between pipes, tubes, or hoses. Flow is allowed when the hole that pierces the ball-shaped disc is in line with the inlet and outlet of the valve. Flow is blocked when the ball is horizontally swiveled 90 degrees, so that the hole of the ball is perpendicular to the opening of the valve. Ball valves can be referred to as full port or reduced port (also known as regular or standard port) depending on the inner diameter of the valve. A ball valve is full port if the hole of the ball is the same size as the inner diameter of the connecting pipeline (resulting in lower friction) and is reduced port if the hole of the valve is one pipe size smaller than the pipe, resulting in less flow through the valve than through the shaft of the pipe. Ball valves may have a handle or lever that aligns with the ball’s position (open or closed) for manual operation. They are primarily used in air, gas, liquid, and steam applications. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 75-100 Series Bronze Ball Valve, Two Piece, Inline, Lockable Lever, 1-1/4 NPT Female
Apollo Valve Apollo 75-100 Series Bronze Ball Valve, Two Piece, Inline, Lockable Lever, 1-1/4 NPT Female"
₱ 2,635.00
Galleon
Go to Shop
Apollo Valve Apollo 32-100 Series Bronze Ball Valve, Two Piece, Inline, Lever, 3/4 NPT Female
Apollo Valve Apollo 32-100 Series Bronze Ball Valve, Two Piece, Inline, Lever, 3/4 NPT Female"
₱ 1,065.00
Galleon
The Apollo 32-100 series two-piece inline ball valve is made of bronze and has a lever handle and female National Pipe Taper (NPT) threaded connections on both ends. This valve is made of bronze for higher strength and corrosion resistance than brass. It has a zinc-plated steel lever handle with a vinyl sleeve for manual on/off control. This ball valve is standard (or regular) port for reduced valve size and cost. The maximum pressure is 400 pounds per square inch (psi) for cold working pressure (CWP) and 125 psi for steam working pressure (SWP), and the maximum temperature is 400 degrees Fahrenheit. The valve is inline for connecting two pipes going in the same direction and has NPT threads on both ends for creating tighter seals than straight threads. Polytetrafluoroethylene (PTFE) seats and reinforced polytetraflouroethylene (RPTFE) stem packing reduce the risk of valve leakage. This valve is for use in water lines, processing plants, and agricultural applications and meets standards MSS SP-110 and CRN: OC10908.5 for quality assurance. Ball valves use a spherical disc to control the flow between pipes, tubes, or hoses. Flow is allowed when the hole that pierces the ball-shaped disc is in line with the inlet and outlet of the valve. Flow is blocked when the ball is horizontally swiveled 90 degrees, so that the hole of the ball is perpendicular to the opening of the valve. Ball valves can be referred to as full port or reduced port (also known as regular or standard port) depending on the inner diameter of the valve. A ball valve is full port if the hole of the ball is the same size as the inner diameter of the connecting pipeline (resulting in lower friction) and is reduced port if the hole of the valve is one pipe size smaller than the pipe, resulting in less flow through the valve than through the shaft of the pipe. Ball valves may have a handle or lever that aligns with the ball’s position (open or closed) for manual operation. They are primarily used in air, gas, liquid, and steam applications. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 93-100 Series Carbon Steel Ball Valve, Unibody, Inline, Lever, 1-1/4 NPT Female
Apollo Valve Apollo 93-100 Series Carbon Steel Ball Valve, Unibody, Inline, Lever, 1-1/4 NPT Female"
₱ 3,046.00
Galleon
The Apollo 93-100 series uni-body inline ball valve is made of carbon steel and has a lever handle and female National Pipe Taper (NPT) threaded connections on both ends. This valve is made from carbon steel for greater strength and hardness than stainless steel it has a nitride coating for corrosion resistance and a zinc-plated steel lever handle with a vinyl sleeve for manual on/off control. The maximum pressure is 2,000 pounds per square inch (gauge) (psig) for water, oil, and gas (WOG) for 1/4” to 1” valves, 1,500 psig for 1-1/4” to 2” valves, and 150 psig for saturated steam, and the temperature range is -20 to 450 degrees Fahrenheit. The valve is inline for connecting two pipes going in the same direction and has NPT threads on both ends for creating tighter seals than straight threads. Reinforced polytetrafluoroethylene (RPTFE) seats and seals reduce the risk of valve leakage and this ball valve is standard (or reduced or regular) port for reduced valve size and cost. This valve is for use with water lines, processing plants, and agricultural applications and meets standard MSS-SP-110 for quality assurance. Ball valves use a spherical disc to control the flow between pipes, tubes, or hoses. Flow is allowed when the hole that pierces the ball-shaped disc is in line with the inlet and outlet of the valve. Flow is blocked when the ball is horizontally swiveled 90 degrees, so that the hole of the ball is perpendicular to the opening of the valve. Ball valves can be referred to as full port or reduced port (also known as regular or standard port) depending on the inner diameter of the valve. A ball valve is full port if the hole of the ball is the same size as the inner diameter of the connecting pipeline (resulting in lower friction) and is reduced port if the hole of the valve is one pipe size smaller than the pipe, resulting in less flow through the valve than through the shaft of the pipe. Ball valves may have a handle or lever that aligns with the ball’s position (open or closed) for manual operation. They are primarily used in air, gas, liquid, and steam applications. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 76F-103-01A Series Stainless Steel Ball Valve, Two Piece, Inline, Lever, 1/2 NPT Female
Apollo Valve Apollo 76F-103-01A Series Stainless Steel Ball Valve, Two Piece, Inline, Lever, 1/2 NPT Female"
₱ 2,872.00
Galleon
The Apollo 76F-100-A series two-piece full port inline ball valve is made of stainless steel and has a lever handle and female National Pipe Taper (NPT) threaded connections on both ends. This valve is made of stainless steel for resistance to corrosion and has a stainless steel lever handle with vinyl sleeve for manual on/off control. The ball valve is full port for reduced friction its inner diameter is the same as the inner diameter of the pipe it connects to enable maximum operating efficiency. The maximum pressure is 1,000 pounds per square inch (gauge) (psig) for cold working pressure (CWP) and 150 psig for saturated steam, and the temperature range is -20 to 450 degrees Fahrenheit. The valve is inline for connecting two pipes going in the same direction and has NPT threads on both ends for creating tighter seals than straight threads. Reinforced polytetrafluoroethylene (RPTFE) seats and seals reduce the risk of valve leakage. This valve is for use with water lines, processing plants, and agricultural applications and meets standard MSS SP-110 for quality assurance. Ball valves use a spherical disc to control the flow between pipes, tubes, or hoses. Flow is allowed when the hole that pierces the ball-shaped disc is in line with the inlet and outlet of the valve. Flow is blocked when the ball is horizontally swiveled 90 degrees, so that the hole of the ball is perpendicular to the opening of the valve. Ball valves can be referred to as full port or reduced port (also known as regular or standard port) depending on the inner diameter of the valve. A ball valve is full port if the hole of the ball is the same size as the inner diameter of the connecting pipeline (resulting in lower friction) and is reduced port if the hole of the valve is one pipe size smaller than the pipe, resulting in less flow through the valve than through the shaft of the pipe. Ball valves may have a handle or lever that aligns with the ball’s position (open or closed) for manual operation. They are primarily used in air, gas, liquid, and steam applications. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 161T-LF Series Bronze Swing Check Valve, Potable Water Service, Class 125, Bronze Seat, 1-1/2 NPT Female
Apollo Valve Apollo 161T-LF Series Bronze Swing Check Valve, Potable Water Service, Class 125, Bronze Seat, 1-1/2 NPT Female"
₱ 3,895.00
Galleon
This class 125 Apollo 161T-LF series swing check valve is a lead-free y-pattern check valve, and can be installed in both horizontal and vertical line with upward flow. The valve body and seat are made of bronze for higher resistance to corrosion than brass, and are resistant to dezincification. It has female NPT threads for connecting to male threaded pipes, creating a tighter seal than straight threads. The maximum cold working pressure (CWP) is 200 pounds per square inch (psi) at 100 degrees Fahrenheit. The working temperature range is -20 to 406 degrees Fahrenheit. This valve meets standards Manufacturers Standardization Society (MSS) SP139, National Sanitation Foundation (NSF)/American National Standards Institute (ANSI) 61-8 Annex F and G, and American Society of Mechanical Engineers (ASME) B1.20.1 for quality assurance. Check valves have two ports and restrict the flow of fluids and other loose materials through a pipe or passageway to one direction. Flow enters through one port and exits through the other, closing when flow reverses or stops. Two common types of check valves are ball cone valves and swing check valves. A ball cone valve utilizes a spring-loaded ball seated against a cone-shaped interior surface to stop the flow of fluid in a forward direction, and a swing check valve has a movable disc on a hinge to block reverse flow. Check valves are rated by their cracking pressure (the minimum upstream pressure required for the valve to operate), and they are used in various water, gas, air, and steam lines. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve 61LF-500 Series Bronze Lead Free Ball Cone Check Valve, In-Line, Soft Seat, 3/4 NPT Female, 400 psi/125 psi Pressure
Apollo Valve 61LF-500 Series Bronze Lead Free Ball Cone Check Valve, In-Line, Soft Seat, 3/4 NPT Female, 400 psi/125 psi Pressure"
₱ 3,698.00
Galleon
The Apollo Valve 61LF-500 series Ball Cone check valve is a lead-free inline valve, and has a soft seat. The valve body and seat are made of bronze for higher resistance to corrosion than brass. Reinforced polytetrafluoroethylene (RPTFE) Ball Cone provides higher chemical resistance. It has female National Pipe Taper (NPT) threads for connecting to male threaded pipes, creating a tighter seal than straight threads. The maximum pressure rating is 400 pounds per square inch (psi), and the maximum steam pressure is 125 psi. The maximum temperature is 350 degrees Fahrenheit. This valve is lead free and complies with California's AB 1953 law for safe drinking water. Check valves have two ports and restrict the flow of fluids and other loose materials through a pipe or passageway to one direction. Flow enters through one port and exits through the other, closing when flow reverses or stops. Two common types of check valves are ball cone valves and swing check valves. A ball cone valve utilizes a spring-loaded ball seated against a cone-shaped interior surface to stop the flow of fluid in a forward direction, and a swing check valve has a movable disc on a hinge to block reverse flow. Check valves are rated by their cracking pressure (the minimum upstream pressure required for the valve to operate), and they are used in various water, gas, air, and steam lines. Apollo Valves manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention. The company, founded in 1928 and headquartered in Matthews, NC, meets international standard International Organization for Standardization (ISO)/IEC 17025:2005 and makes products that meet International Organization for Standardization (ISO) and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 94A Series Brass Ball Valve, Two Piece, Inline, Lever, 1/2 NPT Female
Apollo Valve Apollo 94A Series Brass Ball Valve, Two Piece, Inline, Lever, 1/2 NPT Female"
₱ 780.00
Galleon
The Apollo 94A series two-piece full port inline ball valve is made of brass and has a lever handle and female National Pipe Taper (NPT) threaded connections on both ends. This valve is made of brass for higher corrosion resistance than steel and has a steel lever handle with corrosion resistant plating and a vinyl sleeve for manual on/off control. The ball valve is full port for reduced friction its inner diameter is the same as the inner diameter of the pipe it connects to enable maximum operating efficiency. The maximum pressure is 600 pounds per square inch (psi) for cold working pressure (CWP) for 1/4” to 2” valves and 400 psi CWP for 2-1/2” to 4” valves. The maximum temperature is 400 degrees Fahrenheit. The valve is inline for connecting two pipes going in the same direction and has NPT threads on both ends for creating tighter seals than straight threads. Polytetrafluoroethylene (PTFE) seats and stem packing reduce the risk of valve leakage. This valve is for use with water lines, processing plants, and agricultural applications and meets standard ANSI/NSF 61 for quality assurance. Ball valves use a spherical disc to control the flow between pipes, tubes, or hoses. Flow is allowed when the hole that pierces the ball-shaped disc is in line with the inlet and outlet of the valve. Flow is blocked when the ball is horizontally swiveled 90 degrees, so that the hole of the ball is perpendicular to the opening of the valve. Ball valves can be referred to as full port or reduced port (also known as regular or standard port) depending on the inner diameter of the valve. A ball valve is full port if the hole of the ball is the same size as the inner diameter of the connecting pipeline (resulting in lower friction) and is reduced port if the hole of the valve is one pipe size smaller than the pipe, resulting in less flow through the valve than through the shaft of the pipe. Ball valves may have a handle or lever that aligns with the ball’s position (open or closed) for manual operation. They are primarily used in air, gas, liquid, and steam applications. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 70-600 Series Bronze Ball Valve, Two Piece, 3-Port Diverting, Lever, 1/4 NPT Female
Apollo Valve Apollo 70-600 Series Bronze Ball Valve, Two Piece, 3-Port Diverting, Lever, 1/4 NPT Female"
₱ 1,512.00
Galleon
The Apollo 70-600 series two-piece three-port diverting ball valve is made of bronze and has a lever handle and female National Pipe Taper (NPT) threaded connections on both ends. This valve is made of bronze for higher strength and corrosion resistance than brass and has a zinc-plated steel lever handle with a vinyl sleeve for manual control. This ball valve is three-port diverting to regulate flow among three sections of pipe. Its maximum pressure is 400 pounds per square inch (gauge) (psig) for use with water, oil, and gas (WOG). It has NPT threads on both ends for creating tighter seals than straight threads. Reinforced polytetrafluoroethylene (RPTFE) seats and a PTFE seal reduce the risk of valve leakage. This ball valve is standard (or regular) port for reduced valve size and cost and has a working temperature range of -20 to 450 degrees Fahrenheit. This valve is for use in water lines, processing plants, and agricultural applications and meets standard MSS SP-110 for quality assurance. Ball valves use a spherical disc to control the flow between pipes, tubes, or hoses. Flow is allowed when the hole that pierces the ball-shaped disc is in line with the inlet and outlet of the valve. Flow is blocked when the ball is horizontally swiveled 90 degrees, so that the hole of the ball is perpendicular to the opening of the valve. Ball valves can be referred to as full port or reduced port (also known as regular or standard port) depending on the inner diameter of the valve. A ball valve is full port if the hole of the ball is the same size as the inner diameter of the connecting pipeline (resulting in lower friction) and is reduced port if the hole of the valve is one pipe size smaller than the pipe, resulting in less flow through the valve than through the shaft of the pipe. Ball valves may have a handle or lever that aligns with the ball’s position (open or closed) for manual operation. They are primarily used in air, gas, liquid, and steam applications. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 161T-LF Series Bronze Swing Check Valve, Potable Water Service, Class 125, Bronze Seat, 3/4 NPT Female
Apollo Valve Apollo 161T-LF Series Bronze Swing Check Valve, Potable Water Service, Class 125, Bronze Seat, 3/4 NPT Female"
₱ 1,078.00
Galleon
This class 125 Apollo 161T-LF series swing check valve is a lead-free y-pattern check valve, and can be installed in both horizontal and vertical line with upward flow. The valve body and seat are made of bronze for higher resistance to corrosion than brass, and are resistant to dezincification. It has female NPT threads for connecting to male threaded pipes, creating a tighter seal than straight threads. The maximum cold working pressure (CWP) is 200 pounds per square inch (psi) at 100 degrees Fahrenheit. The working temperature range is -20 to 406 degrees Fahrenheit. This valve meets standards Manufacturers Standardization Society (MSS) SP139, National Sanitation Foundation (NSF)/American National Standards Institute (ANSI) 61-8 Annex F and G, and American Society of Mechanical Engineers (ASME) B1.20.1 for quality assurance. Check valves have two ports and restrict the flow of fluids and other loose materials through a pipe or passageway to one direction. Flow enters through one port and exits through the other, closing when flow reverses or stops. Two common types of check valves are ball cone valves and swing check valves. A ball cone valve utilizes a spring-loaded ball seated against a cone-shaped interior surface to stop the flow of fluid in a forward direction, and a swing check valve has a movable disc on a hinge to block reverse flow. Check valves are rated by their cracking pressure (the minimum upstream pressure required for the valve to operate), and they are used in various water, gas, air, and steam lines. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 80-100 Series Bronze LP-Gas Ball Valve, Two Piece, Inline, Lever, 1-1/4 NPT Female
Apollo Valve Apollo 80-100 Series Bronze LP-Gas Ball Valve, Two Piece, Inline, Lever, 1-1/4 NPT Female"
₱ 3,782.00
Galleon
The Apollo 80-100 series two-piece inline LP-Gas ball valve is made of bronze and has a lever handle and female National Pipe Taper (NPT) threaded connections on both ends. The valve body is made of bronze for higher strength and corrosion resistance than brass and it has a zinc-plated steel lever handle with a vinyl sleeve for manual on/off control. This valve is listed with Underwriters Laboratory (UL) for safe use with liquefied petroleum gas (LP-Gas), natural gas, flammable liquids, and heated oils. The maximum pressure is 600 pounds per square inch (gauge) (psig) for water, oil, and gas (WOG) and 250 for liquefied petroleum gas (LP-Gas). The valve is inline for connecting two pipes going in the same direction and has NPT threads on both ends for creating tighter seals than straight threads. This ball valve has large ports to reduce drops in pressure and has reinforced polytetrafluoroethylene (RPTFE) seats and a PTFE seal to reduce the risk of valve leakage. This valve is for use with LP-Gas lines, water lines, processing plants, and agricultural applications and meets standard MSS SP-110 for quality assurance. Ball valves use a spherical disc to control the flow between pipes, tubes, or hoses. Flow is allowed when the hole that pierces the ball-shaped disc is in line with the inlet and outlet of the valve. Flow is blocked when the ball is horizontally swiveled 90 degrees, so that the hole of the ball is perpendicular to the opening of the valve. Ball valves can be referred to as full port or reduced port (also known as regular or standard port) depending on the inner diameter of the valve. A ball valve is full port if the hole of the ball is the same size as the inner diameter of the connecting pipeline (resulting in lower friction) and is reduced port if the hole of the valve is one pipe size smaller than the pipe, resulting in less flow through the valve than through the shaft of the pipe. Ball valves may have a handle or lever that aligns with the ball’s position (open or closed) for manual operation. They are primarily used in air, gas, liquid, and steam applications. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 70-600 Series Bronze Ball Valve, Two Piece, 3-Port Diverting, Lever, 2 NPT Female
Apollo Valve Apollo 70-600 Series Bronze Ball Valve, Two Piece, 3-Port Diverting, Lever, 2 NPT Female"
₱ 9,374.00
Galleon
The Apollo 70-600 series two-piece three-port diverting ball valve is made of bronze and has a lever handle and female National Pipe Taper (NPT) threaded connections on both ends. This valve is made of bronze for higher strength and corrosion resistance than brass and has a zinc-plated steel lever handle with a vinyl sleeve for manual control. This ball valve is three-port diverting to regulate flow among three sections of pipe. Its maximum pressure is 400 pounds per square inch (gauge) (psig) for use with water, oil, and gas (WOG). It has NPT threads on both ends for creating tighter seals than straight threads. Reinforced polytetrafluoroethylene (RPTFE) seats and a PTFE seal reduce the risk of valve leakage. This ball valve is standard (or regular) port for reduced valve size and cost and has a working temperature range of -20 to 450 degrees Fahrenheit. This valve is for use in water lines, processing plants, and agricultural applications and meets standard MSS SP-110 for quality assurance. Ball valves use a spherical disc to control the flow between pipes, tubes, or hoses. Flow is allowed when the hole that pierces the ball-shaped disc is in line with the inlet and outlet of the valve. Flow is blocked when the ball is horizontally swiveled 90 degrees, so that the hole of the ball is perpendicular to the opening of the valve. Ball valves can be referred to as full port or reduced port (also known as regular or standard port) depending on the inner diameter of the valve. A ball valve is full port if the hole of the ball is the same size as the inner diameter of the connecting pipeline (resulting in lower friction) and is reduced port if the hole of the valve is one pipe size smaller than the pipe, resulting in less flow through the valve than through the shaft of the pipe. Ball valves may have a handle or lever that aligns with the ball’s position (open or closed) for manual operation. They are primarily used in air, gas, liquid, and steam applications. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 161T Series Bronze Swing Check Valve, Class 125, Bronze Seat, 3/8 NPT Female
Apollo Valve Apollo 161T Series Bronze Swing Check Valve, Class 125, Bronze Seat, 3/8 NPT Female"
₱ 2,176.00
Galleon
This class 125 Apollo 161T series swing check valve is a y-pattern check valve, and can be installed in both horizontal and vertical line with upward flow. The valve body and seat are made of bronze for higher resistance to corrosion than brass, and are resistant to dezincification. It has female NPT threads for connecting to male threaded pipes, creating a tighter seal than straight threads. The maximum cold working pressure (CWP) is 200 pounds per square inch (psi) at 100 degrees Fahrenheit, and the maximum steam pressure (SWP) is 125 psi at 353 degrees Fahrenheit. The working temperature range is -20 to 406 degrees Fahrenheit. This valve meets standards Manufacturers Standardization Society (MSS) SP 80, and American Society of Mechanical Engineers (ASME) B1.20.1 for quality assurance. Check valves have two ports and restrict the flow of fluids and other loose materials through a pipe or passageway to one direction. Flow enters through one port and exits through the other, closing when flow reverses or stops. Two common types of check valves are ball cone valves and swing check valves. A ball cone valve utilizes a spring-loaded ball seated against a cone-shaped interior surface to stop the flow of fluid in a forward direction, and a swing check valve has a movable disc on a hinge to block reverse flow. Check valves are rated by their cracking pressure (the minimum upstream pressure required for the valve to operate), and they are used in various water, gas, air, and steam lines. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve 61LF-500 Series Bronze Lead Free Ball Cone Check Valve, In-Line, Soft Seat, 1/2 NPT Female, 400 psi/125 psi Pressure
Apollo Valve 61LF-500 Series Bronze Lead Free Ball Cone Check Valve, In-Line, Soft Seat, 1/2 NPT Female, 400 psi/125 psi Pressure"
₱ 2,277.00
Galleon
The Apollo Valve 61LF-500 series Ball Cone check valve is a lead-free inline valve, and has a soft seat. The valve body and seat are made of bronze for higher resistance to corrosion than brass. Reinforced polytetrafluoroethylene (RPTFE) Ball Cone provides higher chemical resistance. It has female National Pipe Taper (NPT) threads for connecting to male threaded pipes, creating a tighter seal than straight threads. The maximum pressure rating is 400 pounds per square inch (psi), and the maximum steam pressure is 125 psi. The maximum temperature is 350 degrees Fahrenheit. This valve is lead free and complies with California's AB 1953 law for safe drinking water. Check valves have two ports and restrict the flow of fluids and other loose materials through a pipe or passageway to one direction. Flow enters through one port and exits through the other, closing when flow reverses or stops. Two common types of check valves are ball cone valves and swing check valves. A ball cone valve utilizes a spring-loaded ball seated against a cone-shaped interior surface to stop the flow of fluid in a forward direction, and a swing check valve has a movable disc on a hinge to block reverse flow. Check valves are rated by their cracking pressure (the minimum upstream pressure required for the valve to operate), and they are used in various water, gas, air, and steam lines. Apollo Valves manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention. The company, founded in 1928 and headquartered in Matthews, NC, meets international standard International Organization for Standardization (ISO)/IEC 17025:2005 and makes products that meet International Organization for Standardization (ISO) and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 70-100 Series Bronze Ball Valve with Automatic Drain, Two Piece, Inline, Latch-Lock Lever, 1/2 NPT Female
Apollo Valve Apollo 70-100 Series Bronze Ball Valve with Automatic Drain, Two Piece, Inline, Latch-Lock Lever, 1/2 NPT Female"
₱ 1,231.00
Galleon
Go to Shop
Apollo Valve Apollo 70-140 Series Bronze Ball Valve with Stainless Steel 316 Ball and Stem, Two Piece, Inline, Lever, 3/4 NPT Female
Apollo Valve Apollo 70-140 Series Bronze Ball Valve with Stainless Steel 316 Ball and Stem, Two Piece, Inline, Lever, 3/4 NPT Female"
₱ 3,229.00
Galleon
The Apollo 70-140 series two-piece inline ball valve with stainless steel 316 ball and stem is made of bronze and has a lever-handle and female National Pipe Taper (NPT) threaded connections on both ends. For resistance to corrosion, this valve is made of bronze and its ball and stem are made of stainless steel 316. It has a zinc-plated steel lever handle with a vinyl sleeve for manual on/off control. The maximum pressure is 600 pounds per square inch (gauge) (psig) for use with water, oil, and gas (WOG) and 150 psig for saturated steam. The valve is inline for connecting two pipes going in the same direction and has NPT threads on both ends for creating tighter seals than straight threads. Reinforced polytetrafluoroethylene (RPTFE) seats and multifill polytetrafluoroethylene (MPTFE) stem packing reduce the risk of valve leakage. This ball valve is standard (or regular) port for reduced valve size and cost and has a working temperature range of -20 to 450 degrees Fahrenheit. This valve is for use in water lines, processing plants, and agricultural applications and meets standard MSS SP-110 for quality assurance. Ball valves use a spherical disc to control the flow between pipes, tubes, or hoses. Flow is allowed when the hole that pierces the ball-shaped disc is in line with the inlet and outlet of the valve. Flow is blocked when the ball is horizontally swiveled 90 degrees, so that the hole of the ball is perpendicular to the opening of the valve. Ball valves can be referred to as full port or reduced port (also known as regular or standard port) depending on the inner diameter of the valve. A ball valve is full port if the hole of the ball is the same size as the inner diameter of the connecting pipeline (resulting in lower friction) and is reduced port if the hole of the valve is one pipe size smaller than the pipe, resulting in less flow through the valve than through the shaft of the pipe. Ball valves may have a handle or lever that aligns with the ball’s position (open or closed) for manual operation. They are primarily used in air, gas, liquid, and steam applications. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 161T-LF Series Bronze Swing Check Valve, Potable Water Service, Class 125, Bronze Seat, 1-1/4 NPT Female
Apollo Valve Apollo 161T-LF Series Bronze Swing Check Valve, Potable Water Service, Class 125, Bronze Seat, 1-1/4 NPT Female"
₱ 2,219.00
Galleon
This class 125 Apollo 161T-LF series swing check valve is a lead-free y-pattern check valve, and can be installed in both horizontal and vertical line with upward flow. The valve body and seat are made of bronze for higher resistance to corrosion than brass, and are resistant to dezincification. It has female NPT threads for connecting to male threaded pipes, creating a tighter seal than straight threads. The maximum cold working pressure (CWP) is 200 pounds per square inch (psi) at 100 degrees Fahrenheit. The working temperature range is -20 to 406 degrees Fahrenheit. This valve meets standards Manufacturers Standardization Society (MSS) SP139, National Sanitation Foundation (NSF)/American National Standards Institute (ANSI) 61-8 Annex F and G, and American Society of Mechanical Engineers (ASME) B1.20.1 for quality assurance. Check valves have two ports and restrict the flow of fluids and other loose materials through a pipe or passageway to one direction. Flow enters through one port and exits through the other, closing when flow reverses or stops. Two common types of check valves are ball cone valves and swing check valves. A ball cone valve utilizes a spring-loaded ball seated against a cone-shaped interior surface to stop the flow of fluid in a forward direction, and a swing check valve has a movable disc on a hinge to block reverse flow. Check valves are rated by their cracking pressure (the minimum upstream pressure required for the valve to operate), and they are used in various water, gas, air, and steam lines. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 76F-100-A Series Stainless Steel Ball Valve, Two Piece, Inline, Latch-Lock Lever with Nut, 1/4 NPT Female
Apollo Valve Apollo 76F-100-A Series Stainless Steel Ball Valve, Two Piece, Inline, Latch-Lock Lever with Nut, 1/4 NPT Female"
₱ 2,199.00
Galleon
The Apollo 76F-100-A series two-piece full port inline ball valve is made of stainless steel and has a latch-lock lever handle and female National Pipe Taper (NPT) threaded connections on both ends. This valve is made of stainless steel for resistance to corrosion and has a stainless steel latch-lock lever handle with a stainless steel nut and vinyl sleeve for manual on/off control. The lever handle can be locked in either the open or closed position. The ball valve is full port for reduced friction its inner diameter is the same as the inner diameter of the pipe it connects to enable maximum operating efficiency. The maximum pressure is 1,000 pounds per square inch (gauge) (psig) for cold working pressure (CWP) and 150 psig for saturated steam, and the temperature range is -20 to 450 degrees Fahrenheit. The valve is inline for connecting two pipes going in the same direction and has NPT threads on both ends for creating tighter seals than straight threads. Reinforced polytetrafluoroethylene (RPTFE) seats and seals reduce the risk of valve leakage. This valve is for use with water lines, processing plants, and agricultural applications and meets standard MSS SP-110 for quality assurance. Ball valves use a spherical disc to control the flow between pipes, tubes, or hoses. Flow is allowed when the hole that pierces the ball-shaped disc is in line with the inlet and outlet of the valve. Flow is blocked when the ball is horizontally swiveled 90 degrees, so that the hole of the ball is perpendicular to the opening of the valve. Ball valves can be referred to as full port or reduced port (also known as regular or standard port) depending on the inner diameter of the valve. A ball valve is full port if the hole of the ball is the same size as the inner diameter of the connecting pipeline (resulting in lower friction) and is reduced port if the hole of the valve is one pipe size smaller than the pipe, resulting in less flow through the valve than through the shaft of the pipe. Ball valves may have a handle or lever that aligns with the ball’s position (open or closed) for manual operation. They are primarily used in air, gas, liquid, and steam applications. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 72-100 Series Carbon Steel High Pressure Ball Valve, Two Piece, Inline, Lever, 1-1/4 NPT Female
Apollo Valve Apollo 72-100 Series Carbon Steel High Pressure Ball Valve, Two Piece, Inline, Lever, 1-1/4 NPT Female"
₱ 13,930.00
Galleon
The Apollo 72-100 series two piece inline high pressure ball valve is made of carbon steel and has a lever handle and female National Pipe Taper (NPT) threaded connections on both ends. This valve is made from carbon steel for greater strength and hardness than stainless steel and has a zinc phosphate coating for corrosion protection. The maximum pressure is 3,000 pounds per square inch (gauge) (psig) for water, oil, and gas (WOG) and 150 psig for saturated steam, and the temperature range is -20 to 450 degrees Fahrenheit. It has a zinc-plated steel lever handle with a vinyl sleeve for manual on/off control. The valve is inline for connecting two pipes going in the same direction and has NPT threads on both ends for creating tighter seals than straight threads. Reinforced polytetrafluoroethylene (RPTFE) seats and seals reduce the risk of valve leakage and all sizes except 2 inches have full port flow for reduced friction the inner diameter is the same as the inner diameter of the pipe it connects to for maximum operating efficiency. The 2-inch size is standard (or regular) port for reduced valve size and cost. This ball valve is for use with water lines, processing plants, and agricultural applications and meets standard MSS-SP-110 for quality assurance. Ball valves use a spherical disc to control the flow between pipes, tubes, or hoses. Flow is allowed when the hole that pierces the ball-shaped disc is in line with the inlet and outlet of the valve. Flow is blocked when the ball is horizontally swiveled 90 degrees, so that the hole of the ball is perpendicular to the opening of the valve. Ball valves can be referred to as full port or reduced port (also known as regular or standard port) depending on the inner diameter of the valve. A ball valve is full port if the hole of the ball is the same size as the inner diameter of the connecting pipeline (resulting in lower friction) and is reduced port if the hole of the valve is one pipe size smaller than the pipe, resulting in less flow through the valve than through the shaft of the pipe. Ball valves may have a handle or lever that aligns with the ball’s position (open or closed) for manual operation. They are primarily used in air, gas, liquid, and steam applications. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 70-140 Series Bronze Ball Valve with Stainless Steel 316 Ball and Stem, Two Piece, Inline, Lever, 1/4 NPT Female
Apollo Valve Apollo 70-140 Series Bronze Ball Valve with Stainless Steel 316 Ball and Stem, Two Piece, Inline, Lever, 1/4 NPT Female"
₱ 1,811.00
Galleon
The Apollo 70-140 series two-piece inline ball valve with stainless steel 316 ball and stem is made of bronze and has a lever-handle and female National Pipe Taper (NPT) threaded connections on both ends. For resistance to corrosion, this valve is made of bronze and its ball and stem are made of stainless steel 316. It has a zinc-plated steel lever handle with a vinyl sleeve for manual on/off control. The maximum pressure is 600 pounds per square inch (gauge) (psig) for use with water, oil, and gas (WOG) and 150 psig for saturated steam. The valve is inline for connecting two pipes going in the same direction and has NPT threads on both ends for creating tighter seals than straight threads. Reinforced polytetrafluoroethylene (RPTFE) seats and multifill polytetrafluoroethylene (MPTFE) stem packing reduce the risk of valve leakage. This ball valve is standard (or regular) port for reduced valve size and cost and has a working temperature range of -20 to 450 degrees Fahrenheit. This valve is for use in water lines, processing plants, and agricultural applications and meets standard MSS SP-110 for quality assurance. Ball valves use a spherical disc to control the flow between pipes, tubes, or hoses. Flow is allowed when the hole that pierces the ball-shaped disc is in line with the inlet and outlet of the valve. Flow is blocked when the ball is horizontally swiveled 90 degrees, so that the hole of the ball is perpendicular to the opening of the valve. Ball valves can be referred to as full port or reduced port (also known as regular or standard port) depending on the inner diameter of the valve. A ball valve is full port if the hole of the ball is the same size as the inner diameter of the connecting pipeline (resulting in lower friction) and is reduced port if the hole of the valve is one pipe size smaller than the pipe, resulting in less flow through the valve than through the shaft of the pipe. Ball valves may have a handle or lever that aligns with the ball’s position (open or closed) for manual operation. They are primarily used in air, gas, liquid, and steam applications. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 75-100 Series Bronze Ball Valve with Automatic Drain, Two Piece, Inline, Lockable Lever, 1-1/4 NPT Female
Apollo Valve Apollo 75-100 Series Bronze Ball Valve with Automatic Drain, Two Piece, Inline, Lockable Lever, 1-1/4 NPT Female"
₱ 4,621.00
Galleon
The Apollo 75-100 series two-piece inline ball valve with automatic drain is made of bronze and has a lockable lever handle and female National Pipe Taper (NPT) threaded connections on both ends. This valve is made of bronze for higher strength and corrosion resistance than brass. This valve is primarily for use in pneumatic applications it has an automatic drain for releasing air pressure from the pneumatic system to which it is connected. When the valve is in the "on" position, the drain vent is closed when the valve is in the "off" position, air from the downstream system is vented to the atmosphere. This valve has a zinc-plated steel, lockable lever handle that can be locked in either the open or closed position using a portable lock (not included). The pounds per square inch (gauge) (psig) rating for this valve is 600 for water, oil, and gas (WOG) and 150 for saturated steam. It is inline for connecting two pipes going in the same direction and has NPT threads on both ends for creating tighter seals than straight threads. Reinforced polytetrafluoroethylene (RPTFE) seats and multifill polytetrafluoroethylene (MPTFE) stem packing reduce the risk of valve leakage. This ball valve is standard (or regular) port for reduced valve size and cost and has a working temperature range of -20 to 450 degrees Fahrenheit. This valve is for use in water and air applications only and meets standard MSS SP-110 for quality assurance. Ball valves use a spherical disc to control the flow between pipes, tubes, or hoses. Flow is allowed when the hole that pierces the ball-shaped disc is in line with the inlet and outlet of the valve. Flow is blocked when the ball is horizontally swiveled 90 degrees, so that the hole of the ball is perpendicular to the opening of the valve. Ball valves can be referred to as full port or reduced port (also known as regular or standard port) depending on the inner diameter of the valve. A ball valve is full port if the hole of the ball is the same size as the inner diameter of the connecting pipeline (resulting in lower friction) and is reduced port if the hole of the valve is one pipe size smaller than the pipe, resulting in less flow through the valve than through the shaft of the pipe. Ball valves may have a handle or lever that aligns with the ball’s position (open or closed) for manual operation. They are primarily used in air, gas, liquid, and steam applications. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 32-100 Series Bronze Ball Valve, Two Piece, Inline, Lever, 1-1/4 NPT Female
Apollo Valve Apollo 32-100 Series Bronze Ball Valve, Two Piece, Inline, Lever, 1-1/4 NPT Female"
₱ 1,991.00
Galleon
The Apollo 32-100 series two-piece inline ball valve is made of bronze and has a lever handle and female National Pipe Taper (NPT) threaded connections on both ends. This valve is made of bronze for higher strength and corrosion resistance than brass. It has a zinc-plated steel lever handle with a vinyl sleeve for manual on/off control. This ball valve is standard (or regular) port for reduced valve size and cost. The maximum pressure is 400 pounds per square inch (psi) for cold working pressure (CWP) and 125 psi for steam working pressure (SWP), and the maximum temperature is 400 degrees Fahrenheit. The valve is inline for connecting two pipes going in the same direction and has NPT threads on both ends for creating tighter seals than straight threads. Polytetrafluoroethylene (PTFE) seats and reinforced polytetraflouroethylene (RPTFE) stem packing reduce the risk of valve leakage. This valve is for use in water lines, processing plants, and agricultural applications and meets standards MSS SP-110 and CRN: OC10908.5 for quality assurance. Ball valves use a spherical disc to control the flow between pipes, tubes, or hoses. Flow is allowed when the hole that pierces the ball-shaped disc is in line with the inlet and outlet of the valve. Flow is blocked when the ball is horizontally swiveled 90 degrees, so that the hole of the ball is perpendicular to the opening of the valve. Ball valves can be referred to as full port or reduced port (also known as regular or standard port) depending on the inner diameter of the valve. A ball valve is full port if the hole of the ball is the same size as the inner diameter of the connecting pipeline (resulting in lower friction) and is reduced port if the hole of the valve is one pipe size smaller than the pipe, resulting in less flow through the valve than through the shaft of the pipe. Ball valves may have a handle or lever that aligns with the ball’s position (open or closed) for manual operation. They are primarily used in air, gas, liquid, and steam applications. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 75-100 Series Bronze Ball Valve with Automatic Drain, Two Piece, Inline, Lockable Lever, 1 NPT Female
Apollo Valve Apollo 75-100 Series Bronze Ball Valve with Automatic Drain, Two Piece, Inline, Lockable Lever, 1 NPT Female"
₱ 4,310.00
Galleon
The Apollo 75-100 series two-piece inline ball valve with automatic drain is made of bronze and has a lockable lever handle and female National Pipe Taper (NPT) threaded connections on both ends. This valve is made of bronze for higher strength and corrosion resistance than brass. This valve is primarily for use in pneumatic applications it has an automatic drain for releasing air pressure from the pneumatic system to which it is connected. When the valve is in the "on" position, the drain vent is closed when the valve is in the "off" position, air from the downstream system is vented to the atmosphere. This valve has a zinc-plated steel, lockable lever handle that can be locked in either the open or closed position using a portable lock (not included). The pounds per square inch (gauge) (psig) rating for this valve is 600 for water, oil, and gas (WOG) and 150 for saturated steam. It is inline for connecting two pipes going in the same direction and has NPT threads on both ends for creating tighter seals than straight threads. Reinforced polytetrafluoroethylene (RPTFE) seats and multifill polytetrafluoroethylene (MPTFE) stem packing reduce the risk of valve leakage. This ball valve is standard (or regular) port for reduced valve size and cost and has a working temperature range of -20 to 450 degrees Fahrenheit. This valve is for use in water and air applications only and meets standard MSS SP-110 for quality assurance. Ball valves use a spherical disc to control the flow between pipes, tubes, or hoses. Flow is allowed when the hole that pierces the ball-shaped disc is in line with the inlet and outlet of the valve. Flow is blocked when the ball is horizontally swiveled 90 degrees, so that the hole of the ball is perpendicular to the opening of the valve. Ball valves can be referred to as full port or reduced port (also known as regular or standard port) depending on the inner diameter of the valve. A ball valve is full port if the hole of the ball is the same size as the inner diameter of the connecting pipeline (resulting in lower friction) and is reduced port if the hole of the valve is one pipe size smaller than the pipe, resulting in less flow through the valve than through the shaft of the pipe. Ball valves may have a handle or lever that aligns with the ball’s position (open or closed) for manual operation. They are primarily used in air, gas, liquid, and steam applications. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 76-500 Series Stainless Steel Ball Valve, Two Piece, Inline, Spring Return Lever, 3/4 NPT Female
Apollo Valve Apollo 76-500 Series Stainless Steel Ball Valve, Two Piece, Inline, Spring Return Lever, 3/4 NPT Female"
₱ 12,258.00
Galleon
The Apollo 76-500 series two-piece inline ball valve is made of stainless steel and has a spring-return lever handle and female National Pipe Taper (NPT) threaded connections on both ends. This valve is made of stainless steel for resistance to corrosion and has a stainless steel spring-return handle with a vinyl sleeve for manual on/off control. This valve closes automatically when its spring-return lever is released, ensuring that the valve is open only when an operator is at hand. The maximum pressure is 2,000 pounds per square inch (gauge) (psig) for water, oil, and gas (WOG) for 1/4” to 1” valves, 1,500 psig for 1-1/4” to 2” valves, and 150 psig for all sizes for saturated steam. The valve is inline for connecting two pipes going in the same direction and has NPT threads on both ends for creating tighter seals than straight threads. Multifill polytetrafluoroethylene (MPTFE) reinforced seats and stem packing reduce the risk of valve leakage and this ball valve is standard (or reduced or regular) port for reduced valve size and cost. This valve is for use with water lines, processing plants, and agricultural applications and meets standard MSS SP-110 for quality assurance. Ball valves use a spherical disc to control the flow between pipes, tubes, or hoses. Flow is allowed when the hole that pierces the ball-shaped disc is in line with the inlet and outlet of the valve. Flow is blocked when the ball is horizontally swiveled 90 degrees, so that the hole of the ball is perpendicular to the opening of the valve. Ball valves can be referred to as full port or reduced port (also known as regular or standard port) depending on the inner diameter of the valve. A ball valve is full port if the hole of the ball is the same size as the inner diameter of the connecting pipeline (resulting in lower friction) and is reduced port if the hole of the valve is one pipe size smaller than the pipe, resulting in less flow through the valve than through the shaft of the pipe. Ball valves may have a handle or lever that aligns with the ball’s position (open or closed) for manual operation. They are primarily used in air, gas, liquid, and steam applications. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more
Go to Shop
Apollo Valve Apollo 71-500 Series Bronze Ball Valve, Two Piece, Inline, Spring-Close Lever, 1-1/2 NPT Female
Apollo Valve Apollo 71-500 Series Bronze Ball Valve, Two Piece, Inline, Spring-Close Lever, 1-1/2 NPT Female"
₱ 11,976.00
Galleon
The Apollo 71-500 series two-piece inline ball valve is made of bronze and has a spring-close lever handle and female National Pipe Taper (NPT) threaded connections on both ends. This valve is made of bronze for higher strength and corrosion resistance than brass and has a stainless steel spring-close handle with a vinyl sleeve for manual on/off control. This valve closes automatically when its spring-close lever is released, ensuring that the valve is only open when an operator is at hand. The maximum pressure is 600 pounds per square inch (gauge) (psig) for use with water, oil, and gas (WOG) and 150 for saturated steam. The valve is inline for connecting two pipes going in the same direction and has NPT threads on both ends for creating tighter seals than straight threads. Multifill polytetrafluoroethylene (mPTFE) seats and a PTFE seal reduce the risk of valve leakage. This ball valve is standard (or regular) port for reduced valve size and cost. This valve is for use in water lines, processing plants, and agricultural applications and meets standard MSS SP-110 for quality assurance. Ball valves use a spherical disc to control the flow between pipes, tubes, or hoses. Flow is allowed when the hole that pierces the ball-shaped disc is in line with the inlet and outlet of the valve. Flow is blocked when the ball is horizontally swiveled 90 degrees, so that the hole of the ball is perpendicular to the opening of the valve. Ball valves can be referred to as full port or reduced port (also known as regular or standard port) depending on the inner diameter of the valve. A ball valve is full port if the hole of the ball is the same size as the inner diameter of the connecting pipeline (resulting in lower friction) and is reduced port if the hole of the valve is one pipe size smaller than the pipe, resulting in less flow through the valve than through the shaft of the pipe. Ball valves may have a handle or lever that aligns with the ball’s position (open or closed) for manual operation. They are primarily used in air, gas, liquid, and steam applications. Apollo manufactures ball, mixing, and relief valves, actuators, water gauges, marine fittings, heating and plumbing products, and backflow prevention devices. The company, founded in 1928 and headquartered in Matthews, NC, meets International Organization for Standardization ISO/IEC 17025:2005 and makes products that meet ISO and American National Standards Institute (ANSI) standards.
Read more

Hey, we’d like to know what you think of us

We value your privacy at iPrice, your email is only used by us to respond to your feedback.

Thanks!