Hey, we’d like to know what you think of us
Happy
Frown
Happy
Frown
Skip
Thanks!
Go to top
232 products found
Shop now at
Galleon
Small Parts 328 Buna O-Ring, 70A Durometer, Black, 1-7/8 ID, 2-1/4
Small Parts 328 Buna O-Ring, 70A Durometer, Black, 1-7/8 ID, 2-1/4" OD, 3/16" Width (Pack of 25)"
₱ 322.00
This O-ring is made of black Buna-nitrile, is round in cross-section, has a durometer of 70A, and is designed for use in a wide variety of sealing applications. Buna-nitrile can have high tensile strength, and abrasion, tear, and compression set resistance. It can be used in temperatures between -30 degrees F (-34 degrees C) to 250 degrees F (121 degrees C), and is compatible for use with petroleum, HFA, HFB and HFC fluids, vegetable oil, alcohol, acids and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering and should therefore not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. This Buna O-ring has a shore durometer of 70A. Shore durometer is the hardness of a material, and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation on a scale of 0 to 100, with 100 indicating no indentation. O-rings commonly provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various sizes, and can be ordered based on required nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter. These Buna-nitrile O-rings meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings.
Shop now at
Galleon
Small Parts 122 Buna-N O-Ring, 50A Durometer, Round, Black, 1-1/8 ID, 1-5/16
Small Parts 122 Buna-N O-Ring, 50A Durometer, Round, Black, 1-1/8 ID, 1-5/16" OD, 3/32" Width (Pack of 40)"
₱ 590.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts E-Style External Retaining Ring, Tapered Section, Radial Assembly, SAE 1060-1090 Carbon Steel, Phosphate Finish, 1/8 Shaft Diameter, 0.015
Small Parts E-Style External Retaining Ring, Tapered Section, Radial Assembly, SAE 1060-1090 Carbon Steel, Phosphate Finish, 1/8 Shaft Diameter, 0.015" Thick, Made in US (Pack of 100)"
₱ 578.00
Retaining rings attach to a shaft (external) or install in a bore (internal), creating a shoulder to maintain component positioning within an assembly. While most rings install into a machined groove either on the inside or outside diameter of a shaft, self-locking rings attach to a shaft by using friction from means such as teeth and notches to maintain placement. Retaining rings should fit tightly enough into the groove or onto the shaft so they won't experience any movement.
Shop now at
Galleon
Small Parts M1x4 Buna-N O-Ring, 70A Durometer, Round, Black, Buna-N, 4 mm ID, 6 mm OD, 1 mm Width (Pack of 50) at 0.00 PHP from Galleon
Small Parts M1x4 Buna-N O-Ring, 70A Durometer, Round, Black, Buna-N, 4 mm ID, 6 mm OD, 1 mm Width (Pack of 50)
₱ 652.00
This metric O-ring is made of Buna-nitrile (also called Buna-N), round in cross-section, has a durometer of 70A, and is designed for use in a wide variety of sealing applications. Buna-nitrile can have high tensile strength, resistance to abrasion, tear, and compression set resistance. It is acceptable for temperature applications between -30 degrees F (-34 degrees C) to 250 degrees F (121 degrees C). It is compatible for use with petroleum, HFA, HFB, and HFC fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight, and weathering, and should therefore not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. This O-ring has a shore durometer of 70A. Shore durometer is the hardness of a material, and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation on a scale of 0 to 100, with 100 indicating no indentation. O-rings commonly provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves and cylinders of various sorts. They are circular in shape, with a round cross section and a hole in the center, similar to a doughnut. O-rings are available in a number of sizes, and can be ordered based on required inside diameter (ID), outside diameter (OD), and cross-sectional (CS) diameter.
Shop now at
Galleon
Small Parts 913 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 1 ID, 1-2/9
Small Parts 913 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 1 ID, 1-2/9" OD, 1/9" Width (Pack of 1)"
₱ 4,535.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 902 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 1/4 ID, 3/8
Small Parts 902 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 1/4 ID, 3/8" OD, 5/78" Width (Pack of 1)"
₱ 1,914.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 323 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 1-5/16 ID, 1-11/16
Small Parts 323 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 1-5/16 ID, 1-11/16" OD, 3/16" Width (Pack of 1)"
₱ 11,465.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 029 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 1-1/2 ID, 1-5/8
Small Parts 029 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 1-1/2 ID, 1-5/8" OD, 1/16" Width (Pack of 1)"
₱ 5,493.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 046 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 4-1/4 ID, 4-3/8
Small Parts 046 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 4-1/4 ID, 4-3/8" OD, 1/16" Width (Pack of 1)"
₱ 14,283.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 247 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 4-5/8 ID, 4-7/8
Small Parts 247 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 4-5/8 ID, 4-7/8" OD, 1/8" Width (Pack of 1)"
₱ 20,683.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 216 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 1-1/8 ID, 1-3/8
Small Parts 216 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 1-1/8 ID, 1-3/8" OD, 1/8" Width (Pack of 1)"
₱ 6,204.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 240 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 3-3/4 ID, 4
Small Parts 240 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 3-3/4 ID, 4" OD, 1/8" Width (Pack of 1)"
₱ 16,672.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 314 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 3/4 ID, 1-1/8
Small Parts 314 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 3/4 ID, 1-1/8" OD, 3/16" Width (Pack of 1)"
₱ 8,548.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts .103'' (3/32 Nominal) Silicone O-Ring Cord Stock, 70A Durometer, 0.103
Small Parts .103'' (3/32 Nominal) Silicone O-Ring Cord Stock, 70A Durometer, 0.103" Thickness, 10' Piece, Red"
₱ 713.00
This O-ring cord is made of red silicone, has a durometer of 7OA, a round cross-section, and can be used across a wide temperature range (from -65 degrees F/-51 degrees C to 450 degrees F/232 degrees C). Designed for use in a wide variety of sealing applications. Silicone is resistant to ozone, weather, detergent, salt water, engine and transmission oil, non-petroleum brake fluid, hydraulic fluids that resist fire, vegetable and animal oils, and high molecular weight chlorinated aromatic hydrocarbons. Silicone is vulnerable to mechanical wear and tear, water and steam over 250 degrees F/121 degrees C, aromatic hydrocarbons (benzene), chlorinated hydrocarbons (trichloroethylene), acids and bases, and hydrocarbon fuels. The durometer hardness of this silicone O-ring cord is 70A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for rubber, while shore D is used for harder plastics.
Shop now at
Galleon
Small Parts .039'' (1 mm) Buna-N O-Ring Cord Stock, 70A Durometer, 100' Spool, Black at 4364.00 PHP from Galleon
Small Parts .039'' (1 mm) Buna-N O-Ring Cord Stock, 70A Durometer, 100' Spool, Black
₱ 4,364.00
Shop now at
Galleon
Small Parts 246 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 4-1/2 ID, 4-3/4
Small Parts 246 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 4-1/2 ID, 4-3/4" OD, 1/8" Width (Pack of 1)"
₱ 20,000.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 145 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 2-9/16 ID, 2-3/4
Small Parts 145 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 2-9/16 ID, 2-3/4" OD, 3/32" Width (Pack of 1)"
₱ 9,992.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 201 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 3/16 ID, 7/16
Small Parts 201 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 3/16 ID, 7/16" OD, 1/8" Width (Pack of 1)"
₱ 3,074.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 020 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 7/8 ID, 1
Small Parts 020 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 7/8 ID, 1" OD, 1/16" Width (Pack of 1)"
₱ 2,932.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 110 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 3/8 ID, 9/16
Small Parts 110 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 3/8 ID, 9/16" OD, 3/32" Width (Pack of 1)"
₱ 2,807.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 909 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 5/7 ID, 8/9
Small Parts 909 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 5/7 ID, 8/9" OD, 3/31" Width (Pack of 1)"
₱ 2,938.00
Shop now at
Galleon
Small Parts 320 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 1-1/8 ID, 1-1/2
Small Parts 320 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 1-1/8 ID, 1-1/2" OD, 3/16" Width (Pack of 1)"
₱ 11,295.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 148 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 2-3/4 ID, 2-15/16
Small Parts 148 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 2-3/4 ID, 2-15/16" OD, 3/32" Width (Pack of 1)"
₱ 9,844.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 160 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 5-1/4 ID, 5-7/16
Small Parts 160 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 5-1/4 ID, 5-7/16" OD, 3/32" Width (Pack of 1)"
₱ 19,574.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 227 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 2-1/8 ID, 2-3/8
Small Parts 227 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 2-1/8 ID, 2-3/8" OD, 1/8" Width (Pack of 1)"
₱ 11,295.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 008 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 3/16 ID, 5/16
Small Parts 008 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 3/16 ID, 5/16" OD, 1/16" Width (Pack of 1)"
₱ 1,975.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 113 Silicone O-Ring, 70A Durometer, Red, 9/16 ID, 3/4
Small Parts 113 Silicone O-Ring, 70A Durometer, Red, 9/16 ID, 3/4" OD, 3/32" Width (Pack of 100)"
₱ 1,309.00
This silicone O-ring is red in color, round in shape, has a durometer of 7OA, and is designed for use in a wide variety of sealing applications. Silicone is acceptable for temperature applications between -65 degrees F (-54 degrees C) to 450 degrees F (232 degrees C). It has good resistance to ozone, weather, detergent, salt water, engine and transmission oil, non-petroleum brake fluid, hydraulic fluids that resist fire, vegetable and animal oils, and high molecular weight chlorinated aromatic hydrocarbons. Silicone is vulnerable to mechanical wear and tear, water and steam over 250 degrees F (121 degrees C), aromatic hydrocarbons (benzene), chlorinated hydrocarbons (trichloroethylene), acids and bases, and hydrocarbon fuels. O-rings commonly provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section and a hole in the center, similar to a doughnut. O-rings are available in a number of sizes, and can be ordered based on required nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter. This silicone O-ring has a shore durometer of 70A. Shore durometer is the hardness of a material, and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation on a scale of 0 to 100, with 100 indicating no indentation. This silicone O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings.
Shop now at
Galleon
Small Parts 027 Buna-N O-Ring, 50A Durometer, Round, Black, 1-5/16 ID, 1-7/16
Small Parts 027 Buna-N O-Ring, 50A Durometer, Round, Black, 1-5/16 ID, 1-7/16" OD, 1/16" Width (Pack of 35)"
₱ 729.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 230 Buna-N O-Ring, 50A Durometer, Round, Black, 2-1/2 ID, 2-3/4
Small Parts 230 Buna-N O-Ring, 50A Durometer, Round, Black, 2-1/2 ID, 2-3/4" OD, 1/8" Width (Pack of 10)"
₱ 715.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts M1x4 Buna-N O-ring, 70A Durometer, Round, Black, 4 mm ID, 6 mm OD, 1 mm Width (Pack of 100) at 0.00 PHP from Galleon
Small Parts M1x4 Buna-N O-ring, 70A Durometer, Round, Black, 4 mm ID, 6 mm OD, 1 mm Width (Pack of 100)
₱ 1,029.00
This O-ring is made of Buna-nitrile (also called Buna-N), round in cross-section, has a durometer of 70A, and is designed for use in a wide variety of sealing applications. Buna-nitrile can have high tensile strength, resistance to abrasion, tear, and compression set resistance. It is acceptable for temperature applications between -30 degrees F (-34 degrees C) to 250 degrees F (121 degrees C). It is compatible for use with petroleum, HFA, HFB, and HFC fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight, and weathering, and should therefore not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. This O-ring has a shore durometer of 70A. Shore durometer is the hardness of a material, and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation on a scale of 0 to 100, with 100 indicating no indentation. O-rings commonly provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves and cylinders of various sorts. They are circular in shape, with a round cross section and a hole in the center, similar to a doughnut. O-rings are available in a number of sizes, and can be ordered based on required nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter.
Shop now at
Galleon
Small Parts M6x85 Viton O-Ring, 75A Durometer, Round, Black, Viton, 85 mm ID, 97 mm OD, 6 mm Width at 0.00 PHP from Galleon
Small Parts M6x85 Viton O-Ring, 75A Durometer, Round, Black, Viton, 85 mm ID, 97 mm OD, 6 mm Width
₱ 838.00
This metric O-ring is made of black Viton and has a durometer of 75A, a round cross-section, and can be used across a wide temperature range (-15 degrees F/-26 degrees C to 400 degrees F/205 degrees C). Designed for use in a wide variety of sealing applications. Viton (fluorocarbon elastomer) has heat, fuel, and chemical resistance and is compatible for use with non-flammable hydraulic fuels, silicone oil, chlorinated hydrocarbons (trichlorethylene), aromatic hydrocarbons (benzene) and aliphatic hydrocarbons (propane). It works well in high vacuum environments and is vulnerable to low molecular organic acids, ammonia gas, alkalis, amines, glycol-based brake fluids, and super-heated steam. The durometer hardness of this Viton O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for rubber while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in a number of sizes, and can be ordered based on required inside diameter (ID), outside diameter (OD), and cross-sectional (CS) diameter.
Shop now at
Galleon
Small Parts 327 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 1-3/4 ID, 2-1/8
Small Parts 327 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 1-3/4 ID, 2-1/8" OD, 3/16" Width (Pack of 1)"
₱ 14,283.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 114 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 5/8 ID, 13/16
Small Parts 114 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 5/8 ID, 13/16" OD, 3/32" Width (Pack of 1)"
₱ 3,262.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 235 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 3-1/8 ID, 3-3/8
Small Parts 235 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 3-1/8 ID, 3-3/8" OD, 1/8" Width (Pack of 1)"
₱ 14,122.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 221 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 1-7/16 ID, 1-11/16
Small Parts 221 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 1-7/16 ID, 1-11/16" OD, 1/8" Width (Pack of 1)"
₱ 7,977.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 033 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 2 ID, 2-1/8
Small Parts 033 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 2 ID, 2-1/8" OD, 1/16" Width (Pack of 1)"
₱ 6,789.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 215 Buna-N O-Ring, 50A Durometer, Round, Black, 1-1/16 ID, 1-5/16
Small Parts 215 Buna-N O-Ring, 50A Durometer, Round, Black, 1-1/16 ID, 1-5/16" OD, 1/8" Width (Pack of 30)"
₱ 729.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 115 Buna-N O-Ring, 50A Durometer, Round, Black, 11/16 ID, 7/8
Small Parts 115 Buna-N O-Ring, 50A Durometer, Round, Black, 11/16 ID, 7/8" OD, 3/32" Width (Pack of 75)"
₱ 286.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 032 Buna-N O-Ring, 50A Durometer, Round, Black, 1-7/8 ID, 2
Small Parts 032 Buna-N O-Ring, 50A Durometer, Round, Black, 1-7/8 ID, 2" OD, 1/16" Width (Pack of 20)"
₱ 612.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 227 Buna-N O-Ring, 50A Durometer, Round, Black, 2-1/8 ID, 2-3/8
Small Parts 227 Buna-N O-Ring, 50A Durometer, Round, Black, 2-1/8 ID, 2-3/8" OD, 1/8" Width (Pack of 15)"
₱ 587.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 108 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 1/4 ID, 7/16
Small Parts 108 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 1/4 ID, 7/16" OD, 3/32" Width (Pack of 1)"
₱ 2,770.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 234 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 3 ID, 3-1/4
Small Parts 234 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 3 ID, 3-1/4" OD, 1/8" Width (Pack of 1)"
₱ 13,002.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 329 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 2 ID, 2-3/8
Small Parts 329 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 2 ID, 2-3/8" OD, 3/16" Width (Pack of 1)"
₱ 16,587.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 316 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 7/8 ID, 1-1/4
Small Parts 316 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 7/8 ID, 1-1/4" OD, 3/16" Width (Pack of 1)"
₱ 9,340.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 125 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 1-5/16 ID, 1-1/2
Small Parts 125 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 1-5/16 ID, 1-1/2" OD, 3/32" Width (Pack of 1)"
₱ 5,753.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 337 Buna-N O-Ring, 50A Durometer, Round, Black, 3 ID, 3-3/8
Small Parts 337 Buna-N O-Ring, 50A Durometer, Round, Black, 3 ID, 3-3/8" OD, 3/16" Width (Pack of 8)"
₱ 751.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 213 Buna-N O-Ring, 50A Durometer, Round, Black, 15/16 ID, 1-3/16
Small Parts 213 Buna-N O-Ring, 50A Durometer, Round, Black, 15/16 ID, 1-3/16" OD, 1/8" Width (Pack of 35)"
₱ 339.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 035 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 2-1/4 ID, 2-3/8
Small Parts 035 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 2-1/4 ID, 2-3/8" OD, 1/16" Width (Pack of 1)"
₱ 7,782.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 203 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 5/16 ID, 9/16
Small Parts 203 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 5/16 ID, 9/16" OD, 1/8" Width (Pack of 1)"
₱ 3,532.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 121 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 1-1/16 ID, 1-1/4
Small Parts 121 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 1-1/16 ID, 1-1/4" OD, 3/32" Width (Pack of 1)"
₱ 4,537.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 024 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 1-1/8 ID, 1-1/4
Small Parts 024 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 1-1/8 ID, 1-1/4" OD, 1/16" Width (Pack of 1)"
₱ 3,682.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 331 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 2-1/4 ID, 2-5/8
Small Parts 331 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 2-1/4 ID, 2-5/8" OD, 3/16" Width (Pack of 1)"
₱ 17,440.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 134 Buna-N O-Ring, 50A Durometer, Round, Black, 1-7/8 ID, 2-1/16
Small Parts 134 Buna-N O-Ring, 50A Durometer, Round, Black, 1-7/8 ID, 2-1/16" OD, 3/32" Width (Pack of 20)"
₱ 663.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 235 Buna-N O-Ring, 50A Durometer, Round, Black, 3-1/8 ID, 3-3/8
Small Parts 235 Buna-N O-Ring, 50A Durometer, Round, Black, 3-1/8 ID, 3-3/8" OD, 1/8" Width (Pack of 10)"
₱ 706.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 212 Buna-N O-Ring, 50A Durometer, Round, Black, 7/8 ID, 1-1/8
Small Parts 212 Buna-N O-Ring, 50A Durometer, Round, Black, 7/8 ID, 1-1/8" OD, 1/8" Width (Pack of 40)"
₱ 436.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 004 Buna-N O-Ring, 50A Durometer, Round, Black, 5/64 ID, 13/64
Small Parts 004 Buna-N O-Ring, 50A Durometer, Round, Black, 5/64 ID, 13/64" OD, 1/16" Width (Pack of 100)"
₱ 603.00
Shop now at
Galleon
Small Parts 137 Buna-N O-Ring, 50A Durometer, Round, Black, 2-1/16 ID, 2-1/4
Small Parts 137 Buna-N O-Ring, 50A Durometer, Round, Black, 2-1/16 ID, 2-1/4" OD, 3/32" Width (Pack of 15)"
₱ 549.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 114 Buna-N O-Ring, 50A Durometer, Round, Black, 5/8 ID, 13/16
Small Parts 114 Buna-N O-Ring, 50A Durometer, Round, Black, 5/8 ID, 13/16" OD, 3/32" Width (Pack of 80)"
₱ 767.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 023 Simriz 486 White Perfluoroelastomer O-Ring 75A Duro, 1 1/16ID x 1 3/16
Small Parts 023 Simriz 486 White Perfluoroelastomer O-Ring 75A Duro, 1 1/16ID x 1 3/16" OD x 1/16"W , USP Class VI"
₱ 1,052.00
Simriz 486 perfluoroelastomer is particularly suited for the food handlingpharmaceutical and semiconductor industries. Simriz(R) 486 provides excellent chemical and temperature resistance and low contamination from extractables. Suitable for Water For Injection (WFI) Systems, Steam-In-Place (SIP) Cleaning, Ozonated Deionized Water. Recommended for: Acetic Acid, Acetone, Citric Acid, Hydrogen Peroxide, Isopropyl Alcohol, Methyl Ethyl Ketone, Mineral Oil, NaOH, Nitric Acid, Sodium Hypochlorite, soybean Oil, Steam, Toluene, and Xylene.
Shop now at
Galleon
Small Parts 009 Simriz 486 White Perfluoroelastomer O-Ring 75A Duro, 7/32ID x 11/32
Small Parts 009 Simriz 486 White Perfluoroelastomer O-Ring 75A Duro, 7/32ID x 11/32" OD x 1/16"W , USP Class VI"
₱ 629.00
Simriz 486 perfluoroelastomer is particularly suited for the food handlingpharmaceutical and semiconductor industries. Simriz(R) 486 provides excellent chemical and temperature resistance and low contamination from extractables. Suitable for Water For Injection (WFI) Systems, Steam-In-Place (SIP) Cleaning, Ozonated Deionized Water. Recommended for: Acetic Acid, Acetone, Citric Acid, Hydrogen Peroxide, Isopropyl Alcohol, Methyl Ethyl Ketone, Mineral Oil, NaOH, Nitric Acid, Sodium Hypochlorite, soybean Oil, Steam, Toluene, and Xylene.
Shop now at
Galleon
Small Parts 140 Buna-N O-Ring, 50A Durometer, Round, Black, 2-1/4 ID, 2-7/16
Small Parts 140 Buna-N O-Ring, 50A Durometer, Round, Black, 2-1/4 ID, 2-7/16" OD, 3/32" Width (Pack of 15)"
₱ 607.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 136 Buna-N O-Ring, 50A Durometer, Round, Black, 2 ID, 2-3/16
Small Parts 136 Buna-N O-Ring, 50A Durometer, Round, Black, 2 ID, 2-3/16" OD, 3/32" Width (Pack of 15)"
₱ 597.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 008 Buna-N O-Ring, 50A Durometer, Round, Black, 3/16 ID, 5/16
Small Parts 008 Buna-N O-Ring, 50A Durometer, Round, Black, 3/16 ID, 5/16" OD, 1/16" Width (Pack of 125)"
₱ 448.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 161 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 5-1/2 ID, 5-11/16
Small Parts 161 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 5-1/2 ID, 5-11/16" OD, 3/32" Width (Pack of 1)"
₱ 20,000.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 326 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 1-5/8 ID, 2
Small Parts 326 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 1-5/8 ID, 2" OD, 3/16" Width (Pack of 1)"
₱ 13,514.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 905 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 2/5 ID, 5/9
Small Parts 905 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 2/5 ID, 5/9" OD, 1/14" Width (Pack of 1)"
₱ 2,027.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 017 Buna-N O-Ring, 50A Durometer, Round, Black, 11/16 ID, 13/16
Small Parts 017 Buna-N O-Ring, 50A Durometer, Round, Black, 11/16 ID, 13/16" OD, 1/16" Width (Pack of 70)"
₱ 693.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 328 Buna-N O-Ring, 50A Durometer, Round, Black, 1-7/8 ID, 2-1/4
Small Parts 328 Buna-N O-Ring, 50A Durometer, Round, Black, 1-7/8 ID, 2-1/4" OD, 3/16" Width (Pack of 15)"
₱ 684.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 234 Buna-N O-Ring, 50A Durometer, Round, Black, 3 ID, 3-1/4
Small Parts 234 Buna-N O-Ring, 50A Durometer, Round, Black, 3 ID, 3-1/4" OD, 1/8" Width (Pack of 10)"
₱ 128.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 110 Buna-N O-Ring, 50A Durometer, Round, Black, 3/8 ID, 9/16
Small Parts 110 Buna-N O-Ring, 50A Durometer, Round, Black, 3/8 ID, 9/16" OD, 3/32" Width (Pack of 100)"
₱ 706.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 019 Viton O-Ring, 75A Durometer, Round, Brown, 13/16 ID, 15/16
Small Parts 019 Viton O-Ring, 75A Durometer, Round, Brown, 13/16 ID, 15/16" OD, 1/16" Width (Pack of 50)"
₱ 258.00
This O-ring is made of brown Viton and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (-15 degrees F/-26 degrees C to 400 degrees F/205 degrees C). Designed for use in a wide variety of sealing applications, this Viton O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Viton (fluorocarbon elastomer) has high heat, fuel, and chemical resistance, and is compatible for use with non-flammable hydraulic fuels, silicone oil, chlorinated hydrocarbons (trichlorethylene), fuels, aromatic hydrocarbons (benzene) and aliphatic hydrocarbons (propane), as well as high vacuum environments, ozone, and weathering. Viton is vulnerable to low molecular organic acids, ammonia gas, alkalis, amines, glycol-based brake fluids, and super-heated steam. The durometer hardness of this Viton O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 312 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 5/8 ID, 1
Small Parts 312 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 5/8 ID, 1" OD, 3/16" Width (Pack of 1)"
₱ 7,645.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 134 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 1-7/8 ID, 2-1/16
Small Parts 134 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 1-7/8 ID, 2-1/16" OD, 3/32" Width (Pack of 1)"
₱ 7,367.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 032 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 1-7/8 ID, 2
Small Parts 032 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 1-7/8 ID, 2" OD, 1/16" Width (Pack of 1)"
₱ 6,593.00
Shop now at
Galleon
Small Parts 025 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 1-3/16 ID, 1-5/16
Small Parts 025 Kalrez Perfluoroelastomer O-Ring, 6375 Compound, 75A Durometer, Round, Black, 1-3/16 ID, 1-5/16" OD, 1/16" Width (Pack of 1)"
₱ 3,989.00
This O-ring is made of black Kalrez 6375 (perfluoroelastomer) and has a durometer of 75A. It has a round cross-section and can be used across a wide temperature range (27 degrees F/-2.8 degrees C to 527 degrees F/275 degrees C). Designed for use in a wide variety of sealing applications, this Kalrez O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Kalrez 6375 has low compression set and excellent resistance to many reactive gases, plasmas, alkalis, acids and solvents. It performs well in mixed streams, mechanical applications, under temperature cycling, in steam and hot air, and exhibits low swell in acids, and aldehydes. DuPont manufactures Kalrez in facilities that are ISO 9000 and AS 9100 registered. The durometer hardness of this Kalrez O-ring is 75A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 228 Buna-N O-Ring, 50A Durometer, Round, Black, 2-1/4 ID, 2-1/2
Small Parts 228 Buna-N O-Ring, 50A Durometer, Round, Black, 2-1/4 ID, 2-1/2" OD, 1/8" Width (Pack of 10)"
₱ 666.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 034 Viton O-Ring, 90A Durometer, Round, Black, 2-1/8 ID, 2-1/4
Small Parts 034 Viton O-Ring, 90A Durometer, Round, Black, 2-1/8 ID, 2-1/4" OD, 1/16" Width (Pack of 10)"
₱ 603.00
This O-ring is made of black Viton and has a durometer of 90A, a round cross-section, and can be used across a wide temperature range (-15 degrees F /-26 degrees C to 400 degrees F/ 205 degrees C). Designed for use in a wide variety of sealing applications, this Viton O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Viton (fluorocarbon elastomer) has heat, fuel, and chemical resistance and is compatible for use with non-flammable hydraulic fuels, silicone oil, chlorinated hydrocarbons (trichlorethylene), fuels, aromatic hydrocarbons (benzene) and aliphatic hydrocarbons (propane), as well as high vacuum environments, ozone, and weathering. Viton is vulnerable to low molecular organic acids, ammonia gas, alkalis, amines, glycol-based brake fluids, and super-heated steam. The durometer hardness of this Viton O-ring is 90A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 031 Buna-N O-Ring, 50A Durometer, Round, Black, 1-3/4 ID, 1-7/8
Small Parts 031 Buna-N O-Ring, 50A Durometer, Round, Black, 1-3/4 ID, 1-7/8" OD, 1/16" Width (Pack of 25)"
₱ 668.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 146 Buna-N O-Ring, 50A Durometer, Round, Black, 2-5/8 ID, 2-13/16
Small Parts 146 Buna-N O-Ring, 50A Durometer, Round, Black, 2-5/8 ID, 2-13/16" OD, 3/32" Width (Pack of 15)"
₱ 706.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 225 Buna-N O-Ring, 50A Durometer, Round, Black, 1-7/8 ID, 2-1/8
Small Parts 225 Buna-N O-Ring, 50A Durometer, Round, Black, 1-7/8 ID, 2-1/8" OD, 1/8" Width (Pack of 15)"
₱ 674.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 233 Buna-N O-Ring, 50A Durometer, Round, Black, 2-7/8 ID, 3-1/8
Small Parts 233 Buna-N O-Ring, 50A Durometer, Round, Black, 2-7/8 ID, 3-1/8" OD, 1/8" Width (Pack of 10)"
₱ 612.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 330 Buna-N O-Ring, 50A Durometer, Round, Black, 2-1/8 ID, 2-1/2
Small Parts 330 Buna-N O-Ring, 50A Durometer, Round, Black, 2-1/8 ID, 2-1/2" OD, 3/16" Width (Pack of 10)"
₱ 567.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 325 Buna-N O-Ring, 50A Durometer, Round, Black, 1-1/2 ID, 1-7/8
Small Parts 325 Buna-N O-Ring, 50A Durometer, Round, Black, 1-1/2 ID, 1-7/8" OD, 3/16" Width (Pack of 15)"
₱ 643.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 120 Buna-N O-Ring, 50A Durometer, Round, Black, 1 ID, 1-3/16
Small Parts 120 Buna-N O-Ring, 50A Durometer, Round, Black, 1 ID, 1-3/16" OD, 3/32" Width (Pack of 50)"
₱ 282.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 130 Buna-N O-Ring, 50A Durometer, Round, Black, 1-5/8 ID, 1-13/16
Small Parts 130 Buna-N O-Ring, 50A Durometer, Round, Black, 1-5/8 ID, 1-13/16" OD, 3/32" Width (Pack of 25)"
₱ 564.00
Shop now at
Galleon
Small Parts 133 Buna-N O-Ring, 50A Durometer, Round, Black, 1-13/16 ID, 2
Small Parts 133 Buna-N O-Ring, 50A Durometer, Round, Black, 1-13/16 ID, 2" OD, 3/32" Width (Pack of 20)"
₱ 617.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 236 Buna-N O-Ring, 50A Durometer, Round, Black, 3-1/4 ID, 3-1/2
Small Parts 236 Buna-N O-Ring, 50A Durometer, Round, Black, 3-1/4 ID, 3-1/2" OD, 1/8" Width (Pack of 8)"
₱ 709.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 135 Buna-N O-Ring, 50A Durometer, Round, Black, 1-15/16 ID, 2-1/8
Small Parts 135 Buna-N O-Ring, 50A Durometer, Round, Black, 1-15/16 ID, 2-1/8" OD, 3/32" Width (Pack of 20)"
₱ 742.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 128 Buna-N O-Ring, 50A Durometer, Round, Black, 1-1/2 ID, 1-11/16
Small Parts 128 Buna-N O-Ring, 50A Durometer, Round, Black, 1-1/2 ID, 1-11/16" OD, 3/32" Width (Pack of 30)"
₱ 844.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 121 Buna-N O-Ring, 50A Durometer, Round, Black, 1-1/16 ID, 1-1/4
Small Parts 121 Buna-N O-Ring, 50A Durometer, Round, Black, 1-1/16 ID, 1-1/4" OD, 3/32" Width (Pack of 40)"
₱ 592.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 007 Buna-N O-Ring, 50A Durometer, Round, Black, 5/32 ID, 9/32
Small Parts 007 Buna-N O-Ring, 50A Durometer, Round, Black, 5/32 ID, 9/32" OD, 1/16" Width (Pack of 125)"
₱ 623.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 016 Buna-N O-Ring, 50A Durometer, Round, Black, 5/8 ID, 3/4
Small Parts 016 Buna-N O-Ring, 50A Durometer, Round, Black, 5/8 ID, 3/4" OD, 1/16" Width (Pack of 75)"
₱ 708.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 111 Buna-N O-Ring, 50A Durometer, Round, Black, 7/16 ID, 5/8
Small Parts 111 Buna-N O-Ring, 50A Durometer, Round, Black, 7/16 ID, 5/8" OD, 3/32" Width (Pack of 90)"
₱ 679.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 246 Buna-N O-Ring, 50A Durometer, Round, Black, 4-1/2 ID, 4-3/4
Small Parts 246 Buna-N O-Ring, 50A Durometer, Round, Black, 4-1/2 ID, 4-3/4" OD, 1/8" Width (Pack of 5)"
₱ 603.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 334 Buna-N O-Ring, 50A Durometer, Round, Black, 2-5/8 ID, 3
Small Parts 334 Buna-N O-Ring, 50A Durometer, Round, Black, 2-5/8 ID, 3" OD, 3/16" Width (Pack of 8)"
₱ 669.00
Shop now at
Galleon
Small Parts 009 Buna-N O-Ring, 50A Durometer, Round, Black, 7/32 ID, 11/32
Small Parts 009 Buna-N O-Ring, 50A Durometer, Round, Black, 7/32 ID, 11/32" OD, 1/16" Width (Pack of 125)"
₱ 629.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 336 Buna-N O-Ring, 50A Durometer, Round, Black, 2-7/8 ID, 3-1/4
Small Parts 336 Buna-N O-Ring, 50A Durometer, Round, Black, 2-7/8 ID, 3-1/4" OD, 3/16" Width (Pack of 8)"
₱ 751.00
This O-ring is made of black Buna-nitrile (Buna-N) and has a durometer of 50A. It has a round cross-section and can be used across a wide temperature range (-30 degrees F/-34 degrees C to 250 degrees F/121 degrees C). Designed for use in a wide variety of sealing applications, this Buna-nitrile O-ring meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings. Buna-nitrile can have high tensile strength, as well as abrasion, tear, and compression set resistance. It is compatible for use with petroleum, hexafluoroacetone (HFA), hexafluoro-2-butyne (HFB) and hydrofluorocarbon (HFC) fluids, vegetable oil, alcohol, acids, and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering, and should not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. The durometer hardness of this Buna O-ring is 50A. Durometers measure the hardness of a material and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation. On a scale of 0 to 100, a value of 0 indicates that a sample was completely penetrated, while a value of 100 shows no indentation in the sample. The letter following the number identifies the shore scale, which is either shore A or D. Shore A is used for softer plastics, while shore D is used for harder plastics. O-rings provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various AS568A dash sizes, which is the standardized sizing for O-rings, and defines the nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter of an O-ring.
Shop now at
Galleon
Small Parts 417 EPDM O-Ring, 70A Durometer, Round, Black, 3-1/2 ID, 4
Small Parts 417 EPDM O-Ring, 70A Durometer, Round, Black, 3-1/2 ID, 4" OD, 1/4" Width (Pack of 1)"
₱ 248.00
This EPDM O-ring is black in color, round in cross-section, has a durometer of 70A, and is designed for use in a wide variety of sealing applications. EPDM is acceptable for temperature applications between -70 degrees F (-57 degrees C) to 300 degrees F (149 degrees C). It is compatible for use with water and steam, silicone oil and grease, polar solvents (alcohols), acids, glycol-based brake fluids, ozone, and weathering. It is vulnerable to many oils, gasoline, and solvents. This material meets ASTM International standards. This EPDM O-ring has a shore durometer of 70A. Shore durometer is the hardness of a material, and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation on a scale of 0 to 100, with 100 indicating no indentation. O-rings commonly provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section and a hole in the center, similar to a doughnut. O-rings are available in various sizes, and can be ordered based on required nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter. This EPDM O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings.
Shop now at
Galleon
Small Parts 417 Buna-N O-Ring, 70A Durometer, Round, Black, 3-1/2 ID, 4
Small Parts 417 Buna-N O-Ring, 70A Durometer, Round, Black, 3-1/2 ID, 4" OD, 1/4" Width (Pack of 10)"
₱ 480.00
This O-ring is made of black Buna-nitrile, is round in cross-section, has a durometer of 70A, and is designed for use in a wide variety of sealing applications. Buna-nitrile can have high tensile strength, and abrasion, tear, and compression set resistance. It can be used in temperatures between -30 degrees F (-34 degrees C) to 250 degrees F (121 degrees C), and is compatible for use with petroleum, HFA, HFB and HFC fluids, vegetable oil, alcohol, acids and aliphatic hydrocarbons. Buna-nitrile is vulnerable to acetone, ethers, esters, ozone, sunlight and weathering and should therefore not be used in ozone-generating electric motors, welding equipment, or in applications with exposure to UV light. This Buna O-ring has a shore durometer of 70A. Shore durometer is the hardness of a material, and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation on a scale of 0 to 100, with 100 indicating no indentation. O-rings commonly provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves, and various cylinders. They are circular in shape, with a round cross section, and a hole in the center, similar to a doughnut. O-rings are available in various sizes, and can be ordered based on required nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter. These Buna-nitrile O-rings meet standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings.
Shop now at
Galleon
Small Parts 003 Viton O-Ring, 75A Durometer, Black, 1/16 ID, 3/16
Small Parts 003 Viton O-Ring, 75A Durometer, Black, 1/16 ID, 3/16" OD, 1/16" Width (Pack of 5)"
₱ 440.00
This Viton O-ring is black in color, round in shape, has a durometer (hardness) of 75A, and is designed for use in a wide variety of sealing applications. Viton has excellent heat, fuel, and chemical resistance. Viton is acceptable for temperature applications between -15 degrees F (-26 degrees C) to 400 degrees F (205 degrees C). It is compatible for use with non-flammable hydraulic fuels, silicone oil, chlorinated hydrocarbons (trichlorethylene), fuels, aromatic hydrocarbons (benzene) and aliphatic hydrocarbons (propane), as well as high vacuum environments, ozone, and weathering. Viton is vulnerable to low molecular organic acids, ammonia gas, alkalis, amines, glycol-based brake fluids, and super-heated steam. This Viton O-ring has a shore durometer of 75A. Shore durometer is the hardness of a material, and its resistance to permanent indentation. A higher durometer value indicates greater resistance to indentation on a scale of 0 to 100, with 100 indicating no indentation. O-rings commonly provide a pressure and fluid seal between cylindrically shaped, overlapping mating surfaces and are commonly seen in engines, faucets, flanges, valves and various cylinders. They are circular in shape, with a round cross section and a hole in the center, similar to a doughnut. O-rings are available in various sizes, and can be ordered based on required nominal inside diameter (ID), outer diameter (OD), and cross-sectional (CS) diameter. This Viton O-ring meets standards defined by Aerospace Standard AS568A, which is the Aerospace Size Standard for O-rings.

About Small-parts Jewellery Philippines

Small Parts Jewellery Philippines

Basic colors like White, Red and Brown are the most popular colors for Small Parts Jewellery today. 328 Buna O-Ring, 70A Durometer, Black, 1-7/8 ID, 2-1/4" OD, 3/16" Width (Pack of 25)", 122 Buna-N O-Ring, 50A Durometer, Round, Black, 1-1/8 ID, 1-5/16" OD, 3/32" Width (Pack of 40)", E-Style External Retaining Ring, Tapered Section, Radial Assembly, SAE 1060-1090 Carbon Steel, Phosphate Finish, 1/8 Shaft Diameter, 0.015" Thick and Made in US (Pack of 100)" are popular Small Parts Jewellery which you can purchase online. Jiangyuyan, Yoursfs and Blue lans are also available if you are thinking twice about having an Small Parts Jewellery. You can get Small Parts Jewellery for ₱ 128.00 - ₱ 22,049.00 on iprice! If you are looking for Small Parts Jewellery, you can choose between Rings.