Product Categories
Go to top
195 products found
Go to Shop
SunFounder Obstacle Avoidance Sensor Module for Arduino and Raspberry Pi
₱ 904.00
Galleon

Introduction An obstacle avoidance sensor mainly consists of an infrared transmitter, an infrared receiver and a potentiometer. According to the reflecting character of an object, if there is no obstacle, the emitted infrared ray will weaken with the distance it spreads and finally disappear. If there is an obstacle encountered by the infrared rays, the rays will be reflected back to the infrared receiver. Then the receiver detects the signal and confirms an obstacle in front. 3-Pin anti-reverse cable included Power light and signal output indicator included Output digital signals Use a comparator LM393 that works stably Application The module is widely applied in obstacle avoidance robots and cars, and counting in an assembly line. Component List - 1 * Obstacle Avoidance Sensor module - 1 * 3-Pin anti-reverse cable Note: The obstacle should better be white.

Read more
Go to Shop
SunFounder Starter Learning Kit V2.0 for Arduino Beginner fromKnowing to Utilizing With UNO R3 Board - intl
₱ 3,575.00
Lazada
Go to Shop
SunFounder Flame Sensor Module for Arduino and Raspberry Pi
₱ 749.00
Galleon

Introduction 4-Pin anti-reverse cable included Equipped with power light and a signal output indicator Support a detection angle of appr. 60 degrees; particularly sensitive to flame spectrum Connected directly with I/O port of MCU, needless of external circuit Contain an adjustable precision potentiometer for sensitivity adjustment With a comparator LM393 to output both digital and analog signals at the same time Application It is applicable to all kinds of flame and can be used for fire detection (e.g. flame alarm). Component List - 1 x Flame Sensor module - 1 x 4-Pin anti-reverse cable

Read more
Go to Shop
SunFounder 2pcs nRF24L01+ 2.4G Antenna Wireless Transceiver Module for Arduino and Raspberry Pi
₱ 904.00
Galleon

Introduction nRF24L01+ is a single-chip radio transceiver for the worldwide 2.4-2.5 GHz ISM band. The radio transmitters and receivers include frequency generator, enhanced ShockBurst mode controller, power amplifier, crystal oscillator modulator and demodulator. You can select the output power channel and protocol by setting through the SPI port. The current consumption for the nRF24L01+ is extremely low - under the transmitter mode, when the transmitting power is 0dBm, the current consumption is only 11.3mA; under the receiving mode, it is 13.5mA; under the power down and idle mode, the consumption is even lower. As for application, it's widely used in many devices such as wireless mouse and keyboard, game handle, remote control set, industry sensor, toys, etc. For more information, please refer to our WIKI: https://www.sunfounder.com/wiki/index.php?title=NRF24L01_Wireless_Transceiver_Module Specifications Low operation voltage: 1.9-3.6V High speed: 2Mbps 6-channel receiving 125 frequency points Size: 24*15mm Package included 2 x nRF24L01+ Wireless Transceiver Module

Read more
Go to Shop
−4%
SunFounder Tracking Sensor Module for Arduino and Raspberry Pi - Int'l
₱ 853.00 ₱ 896.00
Lazada
Go to Shop
SunFounder New Nano Project Super Starter Kit V2.0 For Arduino UNO R3 Mega2560 Mega328 Nano Including 73 Page Instructions Book
₱ 3,178.00
Galleon

This is a wonderful kit to walk you into the fascinating physical world! Details like module description, principles and code are provided by experiment on the corresponding page in LEARN on our website. Also you can watch related videos. The kit includes some basic tutorials like blinking an LED, controlling a buzzer, etc. 19 Projects Lesson 1 Blinking LED Lesson 2 Controlling an LED by Button Lesson 3 Controlling an LED by PWM Lesson 4 Controlling an LED by Potentiometer Lesson 5 Flowing LED Lights Lesson 6 RGB LED Lesson 7 DC Motor Control Lesson 8 LCD1602 Lesson 9 Serial Monitor Lesson 10 7-Segment Display Lesson 11 74HC595 Lesson 12 Dot-Matrix LED Display Lesson 13 NE555 Timer Lesson 14 Rotary Encoder Lesson 15 ADXL335 Lesson 16 Simple Creation - Light Alarm Lesson 17 Simple Creation - Traffic Light Lesson 18 Simple Creation - Digital Dice Lesson 19 Simple Creation - Small Fan Package included: 1 x Project Box 1 x Booklet 1 x RGB 40 x Pin Header 1x 555 Timer IC 2 x Optocoupler 4N35 2 x Shift Resister 74HC595N 1 x H-Bridge L293D 1 x Accelerometer ADXL335 1 x Rotary Encoder 5 x Push-Button (small) 8 x Resistor 220 Ohm 4 x Resistor 1k Ohm 4 x Resistor 10k Ohm 1 x Resistor 1M Ohm 1 x Resistor 5.1M Ohm 1x Switch 1 x Potentiometer (50kΩ) 1 x LCD1602 Character Display 1 x Dot Matrix Display 8x8 2 x 7-Segment Character Display 1 x DC Motor 16 x LED red 2 x LED white 2 x LED green 2 x LED yellow 2 x NPN Transistor (S8050) 2 x PNP Transistor (S8550) 4 x Capacitor Ceramic (100nF) 4 x Capacitor Ceramic (10nF) 4 x Diode Rectifier 1 x Breadboard 1 x USB Cable 65 x Jumper Wire (Male to Male) 20 x Dupont wire (Female to Male) 1 x Passive Buzzer 1 x Fan

Read more
Go to Shop
SunFounder 5" HD TFT LCD Touch Screen Monitor Display HDMI 800X480 for Raspberry Pi 3, 2 Model B and Raspberry Pi 1 Model B+
₱ 3,556.00
Galleon

Technical Details Introduction Designed for Raspberry Pi, the 5 inch HDMI display screen monitor holds a resistive touch screen with a resolution of 800x480. It supports back-light control with a button on the backside to control. With the HDMI interface, it doesn't occupy any I/O port of Raspberry Pi. This touch screen monitor supports touch screen control and 800 x480 resolution, providing a perfect visual experience for you. We provide a detailed user guide for you, so you won't have to find the solutions here and there. For more information, refer to: http://wiki.sunfounder.cc/index.php?title=5_Inch_LCD_Touch_Screen_Monitor_for_Raspberry_Pi Package included 1 x 5 Inch HDMI LCD Touch Screen Monitor 1 x Stylus 1 x HDMI Connector 4 x M2*16 Copper pillar 4 x M2 Nut

Read more
Go to Shop
SunFounder Ublox NEO-6M GPS Module with Active Antenna EEPROM Aircraft Flight Controller for FPV MWC APM Multirotor Quadcopter Smart Car
₱ 2,382.00
Galleon

Introduction The NEO-6M GPS module is a well-performing complete GPS receiver with a built-in 25 x 25 x 4mm ceramic antenna, which provides a strong satellite search capability. With the power and signal indicators, you can monitor the status of the module. Thanks to the data backup battery, the module can save the data when the main power is shut down accidentally. Its 3mm mounting holes can ensure easy assembly on your aircraft, which thus can fly steadily at a fixed position, return to Home automatically, and automatic waypoint flying, etc. Or you can apply it on your smart robot car for automatic returning or heading to a certain destination, making it a real "smart" bot! For more information, please refer to article on our WIKI: http://wiki.sunfounder.cc/index.php?title=Ublox_NEO-6M_GPS_Module Component List 1 x GPS Module (ceramic antenna included) 1 x 3M Tape

Read more
Go to Shop
SunFounder dual-mode Wireless Bluetooth ELET114 Transceiver SPP BT4.0 ios Android module for Arduino Raspberry Pi 3, 2 Model B & RPi 1 Model B+/B/A+ ect
₱ 1,371.00
Galleon

Introduction The dual mode Bluetooth module supports both SPP protocol and BT4.0, it's compatible with IOS and Android as well as other operating systems. The main chip features high integration level, low cost, low power consumption and superior radio frequency performance. It has a high performance wireless transmit-receive system and it's adaptive to Frequency-Hopping Spread Spectrum. Its transmit-receive distance can reach 50-100meters. In addition, this module is mainly used in wireless data transmission field within a short distance. It can connect to the Bluetooth devices in PC, smart phones as well as other wireless terminal conveniently. The dual mode Bluetooth module can realize the data exchange between the two modules, avoiding the cumbersome cable connection and space constraints, and it can replace the serial cable directly. Application Indoor Localization、Bluetooth wireless data transmission、 Bluetooth gamepad、Bluetooth remote control、Smart remote control car.etc Package List 1 * Bluetooth Module 1 * 4-Pin anti-reverse cable

Read more
Go to Shop
SunFounder 250mm Full Carbon Fiber FPV Mini Race Quadcopter Drone Frame Kit for F3 CC3D NAZE32 ESC Simon 12A Motor MT2204 5045 propellers Openpilot CleanFlight BetaFlight QAV250
₱ 2,186.00
Galleon

Introduction The SunFounder 250 Quadcopter Frame features mini size, great intensity and compact design. The whole frame is made of carbon fiber, and equipped with rubber dampers. Therefore, the SunFounder 250 quadcopter frame boasts ultralight weight and anti-collision ability. In addition, the machine arm its 3mm thickness carbon fiber-made arms endows the drone with anti-shock and anti-collision ability. Thus, it can provide a smooth and stable flight experience for hobbyists. Since it comes with not so many components, it is quite easy to assemble, this frame is perfect for most new and senior pilots. Specifications: Name: SF250 Weight: 138.7g (include Aluminum parts) Diagonal Distance: 250mm Size: 237*183 mm Arms board thickness: 3mm Other board thickness: 1.6mm Recommended Accessories: Flight Controller: F3 /Naze32/ CC3D Camera: Runcam camera /GoPro camera/700TVL HD Camera Motors: 1806/2204/2205/2305 ESC: 12A-20A Propeller: 5 inch Battery: 3S 1300mAh ~ 4S 1300mAh Package Included 1 x SunFounder 250 Frame Kit

Read more
Go to Shop
−4%
SunFounder AD/DA Converter PCF8591 Module for Arduino and Raspberry Pi - Int'l
₱ 982.00 ₱ 1,031.00
Lazada
Go to Shop
SunFounder RAB 5 in 1 Breadboard Holder Base Plate Circuit Board Screws forArduino Uno R3 Mega 2560 Raspberry Pi 3 Model B - intl
₱ 399.00
Lazada
Go to Shop
SunFounder Remote Control Robot Smart Car Kit V2.0 for Arduino Uno R3 Ultrasonic Line Follower Sensor IR Receiver
₱ 8,649.00
Galleon

Introduction This smart car robot kit is a great platform to get started with robots. What we provide are multiple parts, instructions and code needed, so you need to assemble them by yourself, with the help of the user guide. During the course you can thus enjoy the fun of making! Based on the manual in the kit package, you can make the car all by yourself and then create your own sketch to realize different movements of the car as you want. It supports remote control, line following, hand tracking and obstacle avoidance. For further exploration, a sensor shield is used so that there can be more I/Os from the SunFounder Uno, to which more parts can be connected. Download the user manual and code needed on our LEARN page: https://www.sunfounder.com/learn/category/smart-car-kit-v2-0-for-arduino.html Package Included 1 Set x Acrylic Plate 1 set x Screws 1 x Tower Pro MG995 Micro Servo 2 x Gear Motor 2 x Driven Wheel 2 x Driving Wheel 1 x SunFounder Uno 1 x Sensor Shield 1 x DC Motor Driver Module 1 x Step-down DC-DC Converter Module 1 x Switch Module 1 x HC-SR04 Ultrasonic Module 1 x Line Follower Module 1 x IR Receiver Module 1 x IR Remote Controller 1 x 18650x2 Battery Holder 1 x Ribbon (13cm) 1 x USB Data Cable (1m) 1 set x Jumper Wires 1 x Cross Screwdriver 1 x Cross Socket Wrench 1 x Heat Shrink Tube Self-provided Parts 2 x 18650 Rechargeable Li-ion Battery (3.7V) without protection circuit board

Read more
Go to Shop
SunFounder BEE-100S 100mm Micro FPV Racing Quadcopter Drone 600TVL 5.8G 40CH 25mW Camera 2S 8520 DC MOTOR F3 EVO Brush Flight Controller Carbon Fiber Frame Kit Cleanflight Betaflight
₱ 5,033.00
Galleon

Introduction SunFounder BEE-100S is a bee-like quadcopter with miniature and lightweight body especially designed for FPV flying hobbyists. It's palm-sized, featuring stability, agility and activity for stunt flying movements like left-right flip, crossing, etc. The frame and camera of the quadcopter are pre-assembled, so you only need to assemble the battery, propellers and receiver (remote controller and receiver are not included in the kit) to fly it! Moreover, the 600TVL camera with Clover Leaf Antenna is able to transmit real-time FPV image, making the flying easier. For more information, please refer to WIKI on our official website http://wiki.sunfounder.cc/index.php?title=BEE-100/BEE-100S. Check the exciting flight video: https://youtu.be/bZ93paVHDuU. About the flight control: By now, the F3_EVO_Brush flight controller supports a variety of radio transmitters including all models of DSM2/DSMX, RadioLink AT9/AT9S, FRSKY, FLY SKY, WFLY, and Futaba, but note that it does not support the PWM mode. Specification BEE-100S Diagonal distance: 100mm Dimensions: 91x85x27mm (propellers and antennas not included) Weight: 37.5g (battery not included) Flight controller: F3_BRUSH_EVO Operating temperature: -10°C-+40°C Camera Resolution: 600TVL Video output system: PAL/NTSC Video Output: 1.0Vp-p/75 Ohm Power input: 5V Package included 1* BEE-100S kit 8* propellers(4CW+4CCW) 2* 2S Li-Po Battery-452540 1* Cross Screwdriver 1* Propeller Removal Wrench 5* Rubber Band 1* 2S Li-Po Battery USB Charger 1* USB Cable

Read more
Go to Shop
SunFounder Black ABS Cases for Raspberry Pi 3, 2 Model B & Raspberry Pi 1 Model B+
₱ 640.00
Galleon

Introduction This is an elegant and innovative protective case designed specifically for the Raspberry Pi. This two-piece injection-molded ABS enclosure incorporates snap-fit mounting points that hold the Pi securely in place.It also provides the best available protection/accessibility for the Raspberry Pi. Package list 1 x ABS Case 4 x Screws 4 x Foot pads

Read more
Go to Shop
−18%
SunFounder Raspberry Pi 3 Zero Starter kit - Project Super Kit for Raspberry Pi 3 2 Zero Model B+ A+ Including GPIO Breakout Board Breadboard LCD DC Motor LED RGB Dot Matrix 73 Page Manual User Guide - intl
₱ 8,639.00 ₱ 10,606.00
Lazada
Go to Shop
−34%
SunFounder PiPlus 15-in-1 STEM Learning Kit Electronics Building Block For Raspberry Pi 3 2 and RPi 1 Model B Plus - intl
₱ 4,377.00 ₱ 6,706.00
Lazada
Go to Shop
SunFounder Rollflash Bionic Robot Turtle with APP Control forArduino Nano - intl
₱ 6,767.00
Lazada
Go to Shop
SunFounder Smart Home Internet of Things Kit for Arduino Raspberry Pi, Learning How to DIY a Smart Home System
₱ 11,513.00
Galleon

Tutorial1 -How to make a Smart Home System with Arduino Sunfounder Smart Home Kit for Arduino Kit Overview A Brief Introduction to DeviceBit Platform Hardware Description (Photoresistor, Temperature & Humidity Sensor DHT11, Gas Sensor MQ-2, Human Body Pyroelectric Infrared Sensor (PIR), RFID-RC522, Gas Pressure sensor BMP180, RF Transceiver Chip NRF24L01, W5100) Discrete Experiment DeviceBit Platform and Control Board Joint Test (How to Operate DeviceBit Platform, How to Operate Control Board, How to Operate Web app on Mobile Phone) Summary Tutorial2 -How to make a Smart Home System with Arduino&Raspberry Pi What is Smart Home? The Purpose for Developing This Kit Pre-requisites Operation Principle and System Structure DeviceBit Platform An Introduction to Data Acquisition Node Data Processing and Relay Node System Joint Debugging Expansion Summary Smart Home List NRF24L01 * 2 Photoresistor Module * 1 Gas Sensor MQ2 * 1 Temperature and Humidity Sensor DHT11* 1 RFID RC522 * 1 Gas Pressure Sensor BMP180 * 1 Human Body Infrared Sensor PIR * 1 Network Module W5100 * 1 LED (red) * 5 220 Ω Resistor * 5 4 Channel Relay Module * 1 2560 R3 * 1 NANO * 1 Dupont Wire (female to male) * 40 Dupont Wire (male to male)* 20 Dupont Wire (female to female)* 20

Read more
Go to Shop
SunFounder Laser Transmitter Sensor Module for Arduino and Raspberry Pi
₱ 749.00
Galleon

Introduction Operating life cycle: more than 1000h Working current: less than 25mA Operating temperature: -36℃ ~ 65℃ Application The module is applicable to positioning in laser sights, concentricity and medical equipment, laser test tools, signal generator, etc. Component List - 1 * Laser Transmitter module - 1 * 2-Pin anti-reverse cable Note: DO NOT look directly at the laser head. It can cause great harm to your eyes.

Read more
Go to Shop
−4%
SunFounder Analog Temperature Sensor Module for Arduino & Raspberry Pi -Int'l
₱ 632.00 ₱ 663.00
Lazada
Go to Shop
SunFounder LCD Ultrasonic Relay Sensor Electronic Bricks Starter Kit for Arduino UNO R3 Mega2560 Mega328 Nano (with UNO R3) Including 52 Page Instructions Book
₱ 4,391.00
Galleon

In this kit, an Ultrasonic Sensor Module is included. This sensor works by sending a sound wave out and calculating the time it takes for the sound wave to get back to the ultrasonic sensor. By doing this, it can tell us how far the object is away from the sensor. Apart from some basic experiments, more interesting and complicated ones are provided in this kit applying this sensor. Code, Fritzing files and datasheets are free to view and download under the LEARN section on SunFounder website. 15 Projects for Beginners Lesson 1 Button Lesson 2 Flowing LED Lights Lesson 3 Buzzer Lesson 4 Photoresistor Lesson 5 RGB LED Lesson 6 Relay Lesson 7 Tilt-Switch Lesson 8 Servo Lesson 9 LCD1602 Lesson 10 Thermistor Lesson 11 Voltmeter Lesson 12 Ultrasonic Lesson 13 Stopwatch Lesson 14 Automatic Light Source Tracking Lesson 15 Backing a Car Package included: 1 x Project Box 1 x Booklet 1 x 1602 LCD Module 1 x USB Cable 1 x Breadboard 20 x Dupont Wire (Female to Female) 40 x Dupont Wire (Male to Male) 8 x Resistor - 220Ω 4 x Resistor - 1 kΩ 4 x Resistor - 10 kΩ 4 x Resistor - 100 kΩ 1 x Resistor - 1 MΩ 1 x Resistor - 5.1 MΩ 1 x Ultrasonic Sensor Module 1 x Ultrasonic holder 1 x 4-Digit 7-segment 2 x NPN Transistor (S8050) 1 x FET Transistor (2N7000) 2 x Diode Rectifier (1N4007) 1 x Diode (Zener) 1 x Tilt Switch 1 x Photoresistor 1 x Thermistor 2 x Button 2 x Potentiometer (with knob) 1 x Servo Motor 1 x RGB LED 4 x Green LED 4 x Red LED 4 x Yellow LED 1 x Active Buzzer 1 x Relay 40 x Pin Header

Read more
Go to Shop
SunFounder Remote Control Crawling Quadruped Robot Model V2.0 DIY Wooden Kit for Arduino Nano Servo Motor RC Smart Toys Detailed Manual
₱ 11,533.00
Galleon

Introduction This learning kit is based on the popular open source electronics platform Arduino. It is different from most popular kits on the market. With this kit, you cannot only learn how to use Arduino, servo and wireless module but also DIY a cool crawling quadruped robot with wireless remote control. We provide a very detailed manual (code explanation is provided for high-level learning) and technical support for free. And we are ready to answer your questions at any time. If you want to DIY your own robot, this kit is a good start. For more detailes, check the LEARN page. Package Included 1 Set x Acrylic Plate 1 Set x Screws 2 x nRF24l01 Module 2 x SunFounder Nano Board 1 x Remote Controller 1 x Servo Control Board 2 x 18650 Battery Holder 12 x SunFounder Servo 1 x USB Data Cable 1 x Wire Harness Tube (80cm) 1 x Ribbon (50cm) 1 x Calibration Chart 1 x Screwdriver

Read more
Go to Shop
SunFounder Super Strong Stretch Heavy-duty 15" Cargo Net for Motorcycle ATV Stretches to 45" with Iron Hooks
₱ 875.00
Galleon

We are using Latex as material, much stronger and more stretchable than the general rubber! As you see, it can be stretched to about 45". Your motorcycle comes cool with this SUPER cargo net!

Read more
Go to Shop
SunFounder SF-100D FPV AIO Micro Camera 800TVL 1/3 CMOS 5.8G 40CH 25mW Transmitter Combo for Indoor Mini Drone Propeller Inductrix
₱ 1,760.00
Galleon

Introduction This FPV camera is a micro-size and ultra-lightweight all-in-one device, integrating a 5.8G 25mW image transmission module of 40 frequency points and an 800-TVline (TVL) camera. It's already soldered with a 3-leaf-clover antenna, with NTSC and PAL available. In addition, a 1S lithium battery is enough for powering, so you do not need a boost module. The FPV camera has the advantage of low power consumption and is easy to install, which is perfect for small or mini racing drones/aircrafts. In addition, you can get a good performance of image transmission even when it is racing on the other side of the wall. Specifications Operating Voltage: 3.7V - 5.5V Operating Current: 380mA (3.7V) Video Output: PAL or NTSC (selectable) FOV: 148° Horizontal Camera: 800TVL resolution ratio Image Sensor: 1/3 inch HD color CMOS Transmitting Frequency: 5.8G Wireless Channel: 40CH Power Output: 25mW Weight: 6.1g Dimension: 18 x 16.5 x 8mm Component List 1 x Micro FPV Camera 1 x Output Cable 1 x Leaflet

Read more
Go to Shop
SunFounder Basic Sensor Kit for Arduino UNO R3 Mega2560 Mega328 Nano (without controller) Including 87 Page Instructions Book
₱ 4,272.00
Galleon

The kit is special in consisting mainly of sensor modules. Each sensor is made in the format of module which integrates some necessary components, such as comparator, resistor, and capacitor and so on, so it's convenient for circuit connection. This kit can help you "control" the physical world with sensors. Code, Fritzing files and datasheets are free to view and download under the LEARN section on SunFounder website. 35 Experiments with Modules Lesson 1 Hall Sensor Lesson 2 RGB LED Lesson 3 Dual-color Common-Cathode LED Lesson 4 Shock Switch Lesson 5 Knock Sensor Lesson 6 Infrared Transmitter Lesson 7 Laser Transmitter Lesson 8 Reed Switch Lesson 9 Infrared-Receiver Lesson 10 Analog Temperature Sensor Lesson 11 Digital Temperature Sensor Lesson 12 Buzzer Lesson 13 Button Switch Lesson 14 Photo-interrupter Lesson 15 Tilt-Switch Lesson 17 Magic Cup Lesson 18 DS18B20 Temperature Sensor Lesson 19 Rotary Encoder Lesson 20 7-Color Auto-flash LED Lesson 21 Photoresistor Sensor Lesson 22 Humiture Sensor Lesson 23 Obstacle Avoidance Sensor Lesson 24 Tracking Sensor Lesson 25 Microphone Sensor Lesson 26 Metal Touch Sensor Lesson 27 Flame Sensor Lesson 28 Relay Module Lesson 29 Joystick PS2 Lesson 30 MQ-2 Gas Sensor Lesson 31 Password Lock Lesson 32 Lie Detector Lesson 33 Fire Alarm Lesson 34 Thermostatic Water Tank System Lesson 35 Intelligent Environment Monitoring

Read more
Go to Shop
SunFounder PN532 NFC RFID Module Kit Reader Writer with Key Tag for Arduino Android
₱ 1,138.00
Galleon

Introduction SunFounder PN532 NFC RFID Module is a highly integrated transmission module for Near Field Communication at 13.56MHz. With the mode switch on board, you can change easily between I2C, SPI, and UART modes - UART and I2C modes share the same port. The integrated 3.3V voltage regulator provides 3.3V or 5V working voltage for your choice. In addition, it supports RFID reading and writing, and NFC function with Android phone, which makes quite convenient for wireless connection. This module is equipped with two 3mm mounting holes, of which the small dimension makes it easy for using in your project! Note: When your wiring is correct (no short circuit), the module may be a little heated, which is just normal for use. For more information, please refer to the related article on our WIKI: https://www.sunfounder.com/wiki/index.php?title=PN532_NFC_RFID_Module Package included 1 x PN532 NFC Module 1 x Key Tag

Read more
Go to Shop
SunFounder 7" HD 1024x600 TFT LCD Screen Display AV/VGA/HDMI Monitor Built-in Speaker for CCTV Computer PC DVR Home Office Raspberry Pi 3, 2, 1 Model B/ B+ Kano
₱ 4,911.00
Galleon

Technical Details This is a standard 7 inch full color display with high resolution and lower power consumption. It can be applied as a Raspberry Pi display, and works perfect with Raspberry Pi 3, 2 and 1 Model B/B+. Just connect it to the RPi with the HDMI cable in the kit. Also, it can be connected to a CCTV camera via the AV1 port, or vehicle rearview camera (AV2 port) as the monitor. For the latter use, just plug one end of the cable to the display, and the other to the port in the car (the red wire is Power, and black is GND). The real-time video will be on the monitor once it gets signal when you start to reverse to park the car. For more information, refer to: http://wiki.sunfounder.cc/index.php?title=Raspberry_Pi_7%22_HD_1024*600_TFT_LCD_Screen_Display_Settings Specifications -Screen size: 7 inch display -Ration: 16:9/4:3 adjustable -Display Component: color TFT-L -Resolution: 1024 x 600 pixels -Support adjust the brightness, contrast, color -Input signal: PC (VGA), AV1, AV2, HDMI -Power: DC 12V -Consumption: 6W -Video: two way video input -Frequency: PAL/NTSC -Rear watching: image can be changed left and right -Operate mode: the key operation and remote control -Automatically displays blue screen when no signal -Parking rearview priority -Product dimensions: 174 x 114 x 33mm (L x W x D) Package include (HDMI cable is NOT included) 1 x 7 inch TFT LCD Screen 1 x Instruction Manual 1 x IR Remote Controller 1 x 12V 1A Power Supply 1 x Power Cable 1 x Rotatory Stand 1 x Adhesive Tape

Read more
Go to Shop
SunFounder I2C interface 16x2 LCD Pi Plate with KeyPad with RGB LED for Raspberry Pi
₱ 1,449.00
Galleon

Please download the document from this link: https://www.adrive.com/public/zGq5hm/16x2-character-lcd-plus-keypad.pdf

Read more
Go to Shop
−4%
SunFounder 37 Modules Sensor Kit V2.0 for Raspberry Pi 2 and RPiModel B+, 40-Pin GPIO Extension Board Jump Wires - Int'l
₱ 7,972.00 ₱ 8,371.00
Lazada
Go to Shop
−4%
SunFounder Photo-interrupter Module for Arduino and Raspberry Pi - Int'l
₱ 632.00 ₱ 663.00
Lazada
Go to Shop
SunFounder Raspberry Pi Smart Robot Car Kit PiCar-S Block Based Graphical Visual Programming Language Line Following Ultrasonic Sensor Light Following Module Electronic Toy with Detail Manual
₱ 10,479.00
Galleon

Introduction The PiCar-S is a cool smart car that can work with Raspberry Pi model B+, 2 model B and 3 model B. With three sensor modules including ultrasonic obstacle avoidance, light follower, and line follower, you can better learn the programming on how to control the car. Python code is provided for the car, and you can also program and debug it with Dragit, a Snap-based graphical interface, by just simple dragging and dropping the code blocks for complex function. You may visit our website www.sunfounder.com to download the related code and view the user manual on LEARN -> Get Tutorials and watch related videos under VIDEO, or clone the code on our page of github.com at https://github.com/sunfounder/SunFounder_PiCar-S Specification Supply Input Voltage: 7V-12V (by 2 18650 batteries) Dimension: 270x170x80 mm Package included: 1 Set x Acrylic Plate 1 * Robot HATS 1 * PCA9685 PWM Driver 1 * TB6612 Motor Driver 1 * 5-CH Line Follower Module 1 * Ultrasonic Obstacle Avoidance Module 1 * Light Follower Module 2 * 18650 Battery Holder 2 * DC Gear Motor 1 * SunFounder SF0180 Servo 2 * Rear Wheel 2 * Front Wheel 1 * USB Wi-Fi Adapter 1 * Ribbon (30cm) 1 * Cross Screwdriver 1 * Cross Socket Wrench 1 * M2.5/M4 Small Wrench 1 * M2/M3 Small Wrench Several wires Needed screws, nuts, and standoffs

Read more
Go to Shop
SunFounder TRT5000 Tracking Sensor Module for Arduino and Raspberry Pi
₱ 827.00
Galleon

Introduction The IR transmitting tube of TCRT5000 sensor constantly launches infrared light. Since the black absorbs light, when the IR transmitting tube shines on black surface, the reflected light is less and the IR rays received by the receiving tube is less. This indicates the resistance is large, the comparator outputs high level, and the indicator LED goes out. Similarly, when it shines on white surface, the reflected light is more, which indicates the resistance of the receiving tube is lower, the comparator outputs low level, and the indicator LED lights up. 3-Pin anti-reverse cable included Use a comparator LM393 that works stably Adjustable sensitivity Power light and indicator of digital signal output Application The module can be applied to smart tracking car and usually in robot project. Component List - 1 * Tracking Sensor Module - 1 * 3-Pin anti-reverse cable

Read more
Go to Shop
SunFounder High Precision BMP280 Barometric Pressure Temperature Altitude Sensor Module Support I2C or SPI for Arduino and Raspberry Pi
₱ 983.00
Galleon

Introduction The BMP280 is an absolute barometric pressure sensor especially designed for mobile applications. The sensor module is housed in an extremely compact 8-pin metal-lid LGA package with a footprint of only 2.0x2.5mm2 and 0.95mm package height. Its small dimensions and low power consumption of 2.7µA@1Hz allow the implementation in battery-driven devices such as mobile phones, GPS modules or watches. With the I2C and SPI communication, you can apply it in different circumstances. It's a best choice for making experiments like testing altitude and also doing some projects involving air pressure. For more information, please refer to https://www.sunfounder.com/wiki/index.php?title=BMP280_Pressure_Sensor_Module Key parameters Pressure range: 300-1100 hPa (equiv. to +9000--500 m above/below sea level) Package: 8-pin LGA metal-lid Footprint : 2.0 × 2.5 mm², height: 0.95 mm Relative accuracy:±0.12 hPa, equiv. to ±1 m (950-1050hPa @25°C) Absolute accuracy: typ. ±1 hPa (950-1050 hPa, 0-+40 °C) Temperature coefficient offset: 1.5 Pa/K, equiv. to 12.6 cm/K (25-40°C @900hPa) Digital interfaces: I²C (up to 3.4 MHz); SPI (3 and 4 wire, up to 10 MHz) Current consumption: 2.7µA sampling rate Temperature range: -40-+85 °C RoHS compliant, halogen-free MSL 1 Component List 1 * SunFounder BMP280

Read more
Go to Shop
SunFounder Basic Sensor Kit for Raspberry Pi 3, 2 and RPi 1 Model B+ , 40-Pin GPIO Extension Board Jump wires Including 91 Page Instructions Book
₱ 6,370.00
Galleon

The kit is special in consisting mainly of sensor modules. Each sensor is made in the format of module which integrates some necessary components, such as comparator, resistor, and capacitor and so on, so it's convenient for circuit connection. They output signals directly by connecting to an MCU. The kit includes almost all kinds of funny and powerful sensors for Raspberry Pi fans.It can help you "control" the physical world with sensors. Code, Fritzing files and datasheets are free to view and download under the LEARN section on SunFounder website. 31 Experiments with Modules Lesson 1 Hall Sensor Lesson 2 RGB LED Lesson 3 Dual-color Common-Cathode LED Lesson 4 Shock Switch Lesson 5 Knock Sensor Lesson 6 Infrared Transmitter Lesson 7 Laser Transmitter Lesson 8 Reed Switch Lesson 9 Infrared-Receiver Lesson 10 Analog Temperature Sensor Lesson 11 Buzzer Lesson 12 Button Lesson 13 Photo-interrupter Lesson 14 Tilt Switch Lesson 16 Magic Cup Lesson 17 DS18B20 Temperature Sensor Lesson 18 Rotary Encoder Lesson 19 7-Color Auto-flash LED Lesson 20 Photoresistor Lesson 21 DHT11 Humiture Sensor Lesson 22 Obstacle Avoidance Sensor Lesson 23 Tracking Sensor Lesson 24 Microphone Sensor Lesson 25 Metal Touch Sensor Lesson 26 Flame Sensor Lesson 27 Relay Module Lesson 28 Joystick PS2 Lesson 29 MQ-2 Gas Sensor Lesson 30 Temperature Measurement System Lesson 31 Intelligent Temperature Measurement System

Read more
Go to Shop
−50%
SunFounder Raspberry Pi Retro Game Box DIY Arcade Fighting JoystickPush Buttons Controller for RetroPie Raspberry Pi 3/2/B+ - intl
₱ 2,246.00 ₱ 4,492.00
Lazada
Go to Shop
SunFounder Uno R3 Sidekick Basic Starter Kit w/ Breadboard, Jumper wires, Color Led, Resistors, Buzzer For Arduino UNO R3 Mega2560 Mega328 Nano Including 42 Page Instructions Book
₱ 2,400.00
Galleon

There are many small components and sensors in this kit, with which you can learn diverse basic knowledges by following the experiments. Also as you've learnt much during the process, you may explore more functions with the parts provided or use extra devices at hand. This kit is a great one for you to start learning Arduino program. Code, Fritzing files and datasheets are free to view and download under the LEARN section on SunFounder website. 11 Projects for Beginners Lesson 1 Button Lesson 2 Flowing LED Lights Lesson 3 Buzzer Lesson 4 Controlling an LED by Potentiometer Lesson 5 Photoresistor Lesson 6 RGB LED Lesson 7 Servo Lesson 8 Tilt-Switch Lesson 9 Thermistor Lesson 10 Light Alarm Lesson 11 Automatically Tracking Light Source Package included: 1 x Project Box 1 x Booklet 1 x Breadboard 65 x Jumper Wires 10 x Red LED 10 x Green LED 1 x RGB LED 10 x Ceramic Capacitor (10nF) 10 x Ceramic Capacitor (100nF) 5 x Electrolytic Capacitor (100uF) 10 x Resistor (220Ω) 10 x Resistor (1KΩ) 10 x Resistor (10KΩ) 1 x Tilt Switch 1 x Thermistor 1 x Photocell 1 x Diode Rectifier (1N4007) 1 x Active Buzzer 1 x Passive Buzzer 5 x Button 5 x Switch 1 x Mini Servo 1 x Potentiometer with Knob 1 x NPN Transistor

Read more
Go to Shop
SunFounder 7"IPS Display Panel Monitor 1024*600 HD LCD AudioHDMI/VGA/NTSC/PAL Screen for Raspberry Pi 3,2 Model B+/A+B Kano
₱ 3,819.00
Lazada
Go to Shop
SunFounder Starter Learning Kit for Arduino Beginner, from Knowing to Utilizing Including 82 Page Instructions Book
₱ 4,382.00
Galleon

21 Projects: 1 Controlling LED by Button 2 Controlling LED by PWM 3 Interactive LED Flowing Lights 4 LCD1602 5 Buzzer 6 Tilt-Switch 7 Answer Machine 8 Serial Monitor 9 Photoresistor 10 Controlling Voice by Light 11 Voltmeter 12 LM35 Temperature Sensor 13 One Digit 7-Segment Display 14 Stopwatch 15 RGB LED 16 74HC595 17 Relay Module 18 Stepper Motor 19 Servo 20 Joystick PS2 21 Infrared-Receiver Package Including SunFounder UNO R3 Prototype Shield 820 Breadboard Red Light LED *5 Yellow Light LED *5 Blue Light LED *5 Resistor 10K *5 Resistor 1K *5 Resistor 220R *8 74HC595 Active Buzzer Passive Buzzer 1-digital 8 segment display 4-digital 8 segment display Press Button *10 Photo Resistor *3 Potentiometer LM35 temperature Infrared receiver Frame sensor Tilt switch sensor Remote controller 1602 LCD PS2 Joystick Stepper Motor Stepper Motor Driver Board Servo motor RGB Module Relay Module Jumper wire*30 Dubond Wire *10 2.54 Pin USB Cable

Read more
Go to Shop
−7%
SunFounder MARS Board - compatible with Arduino UNO R3 ATmega328PType C 2016 Latest Version - intl
₱ 5,689.00 ₱ 6,173.00
Lazada
Go to Shop
SunFounder Basic Sensor Kit for Arduino UNO R3 Mega2560 Mega328 Nano (with UNO R3) Including 87 Page Instructions Book
₱ 4,344.00
Galleon

The kit is special in consisting mainly of sensor modules. Each sensor is made in the format of module which integrates some necessary components, such as comparator, resistor, and capacitor and so on, so it's convenient for circuit connection. This kit can help you "control" the physical world with sensors. Code, Fritzing files and datasheets are free to view and download under the LEARN section on SunFounder website. 35 Experiments with Modules Lesson 1 Hall Sensor Lesson 2 RGB LED Lesson 3 Dual-color Common-Cathode LED Lesson 4 Shock Switch Lesson 5 Knock Sensor Lesson 6 Infrared Transmitter Lesson 7 Laser Transmitter Lesson 8 Reed Switch Lesson 9 Infrared-Receiver Lesson 10 Analog Temperature Sensor Lesson 11 Digital Temperature Sensor Lesson 12 Buzzer Lesson 13 Button Switch Lesson 14 Photo-interrupter Lesson 15 Tilt-Switch Lesson 17 Magic Cup Lesson 18 DS18B20 Temperature Sensor Lesson 19 Rotary Encoder Lesson 20 7-Color Auto-flash LED Lesson 21 Photoresistor Sensor Lesson 22 Humiture Sensor Lesson 23 Obstacle Avoidance Sensor Lesson 24 Tracking Sensor Lesson 25 Microphone Sensor Lesson 26 Metal Touch Sensor Lesson 27 Flame Sensor Lesson 28 Relay Module Lesson 29 Joystick PS2 Lesson 30 MQ-2 Gas Sensor Lesson 31 Password Lock Lesson 32 Lie Detector Lesson 33 Fire Alarm Lesson 34 Thermostatic Water Tank System Lesson 35 Intelligent Environment Monitoring

Read more
Go to Shop
−4%
SunFounder Sunfounder New 2in1 220V 30W Solder Sucker Soldering IronDesoldering Pump Removal Tool Kit
₱ 1,031.00 ₱ 1,083.00
Lazada
Go to Shop
SunFounder New Uno R3 For Arduino ATMEGA328P ATMEGA16U2
₱ 1,138.00
Galleon

Technical Details: Microcontroller: ATmega328 Operating Voltage: 5V Input Voltage (recommended): 7-12V Input Voltage (limits): 6-20V Digital I/O Pins: 14 (of which 6 provide PWM output) Analog Input Pins: 6 DC Current per I/O Pin: 40 mA DC Current for 3.3V Pin: 50 mA Flash Memory: 32 KB (ATmega328) of which 0.5 KB used by bootloader SRAM: 2 KB (ATmega328) EEPROM: 1 KB (ATmega328) Clock Speed: 16 MHz Package included: 1x SunFounder UNO R3 (Arduino compatible)

Read more
Go to Shop
SunFounder Dual Band ANTENNA SMA-F 136-174&400-520MHz For BAOFENG Two-way Radio UV-5R/5RA/5RB/5RC/5RD/5RE/5REPLUS/3R+
₱ 749.00
Galleon

Specifications: Frequency: 136-174/400-520Mhz Connector SMA-Female Max power N/A V.S.W.R. Less 1.5 Impedance 50 OHM Length 17.5CM Gain N/A Weight 18g High gain Dual Band antenna Connector:SMA- female

Read more
Go to Shop
−4%
SunFounder Analog Hall Sensor Module for Arduino and Raspberry Pi - Int'l
₱ 632.00 ₱ 663.00
Lazada
Go to Shop
SunFounder Raspberry Pi Smart Video Car Kit V2.0 Block Based Graphical Visual Programming Language Remote Control by UI on Windows/Mac and Web Browser Electronic Toy with Detail Manual
₱ 10,091.00
Galleon

Introduction The PiCar-V is an open source robot learning kit on Raspberry Pi. Equipped with a wide-angle USB webcam, it is powerful together with three whole new circuit boards with less but simpler wiring, some acrylic plates in a well-designed structure, and complete code suitable for almost all platforms to control the car. Python code is provided for the car, and you can also program and debug it with Dragit, a Snap-based graphical interface, by just simple dragging and dropping the code blocks for complex function. There are many ways to control the robot remotely: with the app on PC (works on any OS), you can control the car and the cam's direction on the UI and view the image it takes in real time; or, with the related code, realize the same functions on a web browser, meaning it works with any mobile phones, tablets, etc. Specifications Supply Input Voltage: 7V-12V (by 2 18650 batteries) Dimensions: 270x170x110 mm Package included: 1 * Robot HATS 1 * PCA9685 PWM Driver 1 * TB6612 Motor Driver 1 * 2x18650 Battery Holder 2 * DC Gear Motor 3 * SunFounder SF0180 Servo 1 * 120° Wide-angle USB Camera 2 * Rear Wheel 2 * Front Wheel 1 * USB Wi-Fi Adapter 1 * Ribbon (30cm) 1 * Cross Screwdriver 1 * Cross Socket Wrench 1 * M2.5/M4 Small Wrench 1 * M2/M3 Small Wrench Several wires Needed screws, nuts, and standoffs

Read more
Go to Shop
SunFounder Full Color RGB LED Matrix Driver Shield + RGB Matrix Screen - intl
₱ 1,003.00
Lazada
Go to Shop
−4%
SunFounder Button Module for Arduino and Raspberry Pi - Int'l
₱ 426.00 ₱ 447.00
Lazada
Go to Shop
SunFounder GPIO Extension Board T Shape for Raspberry Pi 3, 2 Model B & RPi 1 Model B+, with 40 Pins Ribbon Cable
₱ 983.00
Galleon

Introduction This T-shape extension board, as the name suggests, is to extend the GPIOs of a Raspberry Pi. Underneath the power and GND pins can be plugged into the + and - rails on a breadboard, making it easy and neat to connect. A filter capacitor is added between the power and GND for steady voltage output. With this T_Extension Board, you can make your experiments more conveniently and easily! Package included: 1 x T-Extension Board with 40-pin Ribbon Cable

Read more
Go to Shop
SunFounder 8 Channel Logic Level Converter Bi-Directional Shifter Module 5V to 3.3V for Raspberry Pi and Arduino
₱ 728.00
Galleon

Introdction The Sunfounder level converter is a device that safely steps down 5V signals to 3.3V and steps up 3.3V to 5V at the same time. This level converter also works with 2.8V and 1.8V devices. The board needs to be powered from the two voltages sources that your system is using. When the two devices are connected for communicating, if the input signal is inconsistent with the output signal, the communication will be interrupted. The SunFounder level converter is born for solving this problem. HV inputs high level, LV inputs low level and GND is connected to the common ground wire. Package included 1x Level Converter

Read more
Go to Shop
−4%
SunFounder Sunfounder Tin Wire Frame Stander Metal Solder Soldering Iron StandHolder Base
₱ 570.00 ₱ 598.00
Lazada
Go to Shop
SunFounder DIY 4-Axis Wooden Servo Control Robotic for Arduino ArmKit Rollarm - intl
₱ 4,164.00
Lazada
Go to Shop
SunFounder Digital Compass HMC5883L Module for Arduino and Raspberry Pi
₱ 904.00
Galleon

Introduction The module includes a state-of-the-art, high-resolution HMC118X series magneto-resistive sensor, plus an ASIC containing amplification, automatic degaussing strap drivers, offset cancellation, and a 12-bit ADC that enables 1° to 2° compass heading accuracy. The I2C serial bus allows for easy interface. Application Mobile Phones Netbooks Consumer Electronics Auto Navigation Systems Personal Navigation Devices Component List - 1 * HMC5883L Module - 1 * Straight Pin Header - 1 * Right-angle Pin Header

Read more
Go to Shop
−4%
SunFounder Sunfounder Metal Soldering Iron Gun Stand Holder Support BaseSponge
₱ 887.00 ₱ 931.00
Lazada
Go to Shop
SunFounder Ultimate UNO R3 Sensor Kit V2.0 for Arduino UNO R3 Mega2560 Mega328 Nano Including 98 Page Instructions Book
₱ 6,467.00
Galleon

The kit is special in consisting mainly of sensor modules. Each sensor is made in the format of module which integrates some necessary components, such as comparator, resistor, and capacitor and so on, so it's convenient for circuit connection. This kit can help you "control" the physical world with sensors. Code, Fritzing files and datasheets are free to view and download under the LEARN section on SunFounder website. 36 Experiments with Modules Lesson 1 Display by I2C LCD1602 Lesson 2 Analog Hall Sensor Lesson 3 Switch Hall Sensor Lesson 4 Analog Temperature Sensor Lesson 5 Temperature Detection by Thermistor Lesson 6 Auto-flash LED Lesson 7 Barometer Lesson 8 Real-time Clock Module Lesson 9 Flame Alarm Lesson 10 Flammable Gas Detection Lesson 11 Humiture Detection Lesson 12 Joystick PS2 Lesson 13 Controlling an LED by Button Lesson 14 Vibration Switch Lesson 15 Touch Switch Lesson 16 Photo-interrupter Lesson 17 Photoswitch Lesson 18 Reed Switch Lesson 19 Relay Lesson 20 Blinking an LED by Potentiometer Lesson 21 Tilt Switch Lesson 22 Buzzer Lesson 23 Digital Temperature Sensor Lesson 24 Rainbow LED Lesson 25 Infrared Receiver Lesson 26 Dual-color LED Lesson 27 Sound Sensor Lesson 28 Rotary Encoder Lesson 29 Laser Transmitter Lesson 30 IR Tracking Sensor Lesson 31 IR Obstacle Avoidance Sensor Lesson 32 Color Detection Lesson 33 Analog-Digital Converter Lesson 34 Raindrop Detection Lesson 35 Distance Detection by Ultrasonic Lesson 36 Thermostatic Water Tank

Read more
Go to Shop
SunFounder 4-Channel DC 5V Relay Module with Optocoupler High Level Trigger Expansion Board for Arduino and Raspberry Pi DSP AVR PIC ARM
₱ 983.00
Galleon

Introduction This is a 4-channel HIGH level trigger relay, applicable to Arduino and Raspberry Pi, Relays are suitable for driving high power electronic devices such as lights, electric fans and air conditions. There are two soldering points for 5V and GND at the two ends of the module. So you can just weld other relay modules to it and have a relay module of more channels, signals of which are independent of each other. You can just unplug the headers to disconnect the device with the module after the experiment and don't need to unscrew the wires in the socket. Kindly reminder: Be careful with your fingers when unplugging the headers. For more information, refer to: http://wiki.sunfounder.cc/index.php?title=4-Channel_High_Level_Trigger_Relay Component List 1 x 4-Channel Relay Module

Read more
Go to Shop
SunFounder Step Down DC-DC DC to DC Converter Module for Raspberry Pi
₱ 904.00
Galleon

Application The module can be applied to power supply for electronic devices. When a 5v supply is needed, the module can be used to reduce the voltage and obtain a 5v supply Component List - 1 * Step-down DC-DC Converter Module for Raspberry Pi

Read more
Go to Shop
SunFounder Mifare RC522 Card Read Antenna RF Module RFID Reader IC Card Proximity Module for Arduino
₱ 1,216.00
Galleon

Introduction RFID module The original Philips MFRC522 chip design circuit card reader is easy to use and low cost, and applies to the user equipment development, the reader and the development of advanced applications, and the need for the user RF card terminal design/production. This module can be directly loaded into various reader modules. It utilizes a voltage of 3.3V, through the SPI interface with simply a few wires. Directly connected with a CPU motherboard, the module can work in a stable and reliable manner as a distance card reader. For more information,refer to https://www.sunfounder.com/wiki/index.php?title=Mifare_RC522_Module_RFID_Reader Specifications Operating current: 13-26mA/DC 3.3V Idle current: 10-13mA/ DC 3.3V Sleep current: Peak current: Operating frequency: 13.56MHz Supported card types: Mifare1 S50, Mifare1 S70, MIFARE Ultralight, Mifare Pro, and MIFARE DESFire Physical features: size: 40mm×60mm Ambient operating temperature: - 20-80 degrees centigrade Ambient storage temperature: - 40-85 degrees centigrade Ambient relative humidity: 5%-95% Package included 1 * RFID RC522 module 1 * RFID key fob 1 * RFID Card

Read more
Go to Shop
SunFounder DS18B20 Temperature Sensor Module for Arduino and Raspberry Pi
₱ 953.00
Galleon

Introduction Support special single-line interface; to connect DS18B20 with an MCU, only a port line is needed for the two-way communication. With power light and signal output indicator Output digital signals 3-Pin anti-reverse cable included Application The module can be applied to temperature measurement and control in devices such as freezer, barn, storage tank, telecom cabinet, electricity cabinet, cable slot, etc. It can be used to measure the temperature in non-extreme temperature occasions, like cable trench and boiler, etc. Component List - 1 * DS18B20 Temperature Sensor Module - 1 * 3-Pin anti-reverse cable

Read more
Go to Shop
SunFounder RollbotMicro STEM Learning Educational DIY Robotics Kit GUI-Mixly for Arduino Beginner Infrared Sensor OLED Module Desk Car Robot
₱ 6,090.00
Galleon

Introduction RollbotMicro kit is a very interesting and suitable learning tool for Arduino and robot hobbyist. It has simple structure and runs PCB as the main structure of the robot. As it is based on the Arduino platform, we can learn programming from easy to difficult so as to achieve the control of the robot. This funny mini robot is composed of an integrated PCB, two driving wheels and a universal wheel. It is charged by the rechargeable Li-ion battery and compatible with the Arduino board. Accessories including an OLED screen and an infrared sensor module. In addition, the integrated board contains the control of the N20 gear motor and the OLED screen. This kit is also equipped with a battery charger and a simple but delicate map for you to play the game via the line following function. Check the introduction and assembly tutorial videos: https://www.sunfounder.com/video/category/?cat=46 Download the documentation and code at: https://www.sunfounder.com/learn/category/RollbotMicro.html Package Included 1 x User Manual 1 Set x Screws 2 x N20 Gear Motor 2 x N20 Motor Mount 1 x Main Board 1 x OLED Screen 1 x Infrared Sensor 1 x Universal Wheel 2 x Wheel 1 x Battery 1 x 3.7V USB Charger 1 x USB Type-C Cable 1 x Double-sided Tape 1 x OLED Cover 1 x Test card 1 x Black Tape 1 x Marker Pen 3 x Guide Card 3 1 x Map 1 x Screw driver

Read more
Go to Shop
−4%
SunFounder Touch Switch Module for Arduino and Raspberry Pi - Int'l
₱ 781.00 ₱ 820.00
Lazada
Go to Shop
SunFounder FT232RL FTDI USB to TTL Serial Adapter Module 3.3V 5V for Arduino Raspberry Pi
₱ 904.00
Galleon

Introdction This USB to TTL serial adapter module can work with different types of computer systems and drivers. The power LED, TXD LED and RXD LED on the module can help indicate whether it works normally. With the build-in signal voltage switch, when you switch to 5V, the power at TXD and RXD will be 5V; if you switch to 3.3V, then the power is 3.3V. Therefore, if your device can take only 3.3V input, this module is a great choice. A 500mA self-restore fuse is used for over current protection. The module can also be used for general serial applications. Package included 1 x USB-to-Serial Adapter Module

Read more
Go to Shop
−4%
SunFounder MQ-2 Gas Sensor Module for Arduino and Raspberry Pi - Int'l
₱ 998.00 ₱ 1,048.00
Lazada
Go to Shop
SunFounder 210Pcs Assorted M3 M2.5 Nylon Screws Nut Standoffs Spacers for DIY Aircraft Arduino Raspberry Pi FPV RC Drone PC mods
₱ 1,301.00
Galleon

Introduction The kit is normally used in aircrafts, Arduino and Raspberry Pi related products. With good fixing performance and multiple types, it's easy to use and quite suitable for fixing the products in different thicknesses. Components in this kit are made of nylon material, making them firmer and more anticorrosive, and will not rust like metal. What's more, this kit is also equipped with an M2 screwdriver, needless of buying a new one. The package box is beautifully designed to separate different types of components, making it more portable and easy to use. Package Included 10 x Spacers Male-Female (6mm + 6mm, M3) 10 x Spacers Male-Female (8mm + 6mm, M3) 10 x Spacers Male-Female (10mm + 6mm, M3) 10 x Spacers Male-Female (12mm + 6mm, M3) 10 x Spacers Male-Female (15mm + 6mm, M3) 10 x Spacers Male-Female (20mm + 6mm, M3) 60 x Screws (M3 x 6mm) 60 x Nuts (M3) 10 x Spacers Male-Female (11mm + 6mm, M2.5) 10 x Screws (M2.5 x 6mm) 10 x Nuts (M2.5) 1 x M2 Screwdriver

Read more
Go to Shop
−16%
SunFounder Raspberry Pi 3 Zero Starter kit - Project Super Kit V3.0 for Raspberry Pi 3 2 Zero Model B+ A+ Including GPIO Breakout Board Breadboard LCD DC Motor RGB Matrix 123 Page Manual User Guide - intl
₱ 10,068.00 ₱ 12,004.00
Lazada
Go to Shop
SunFounder Photoresistor Light Sensor Module for Arduino and Raspberry Pi
₱ 749.00
Galleon

Application It is applicable to light intensity detection, related detection sensors, smart car light-seeking module, etc. Component List - 1 x Photoresistor Sensor Module - 1 x 3-Pin anti-reverse cable

Read more
Go to Shop
−30%
SunFounder Official Raspberry Pi Foundation 7" Touchscreen LCD Display Monitor - intl
₱ 4,629.00 ₱ 6,699.00
Lazada
Go to Shop
−50%
SunFounder Raspberry Pi 2.4 Inch TFT Screen LCD Display HATExtension Board 320*240 for Raspberry Pi 3/2/B+ - intl
₱ 1,164.00 ₱ 2,350.00
Lazada
Go to Shop
SunFounder Sunfounder 7" HD 1024*600 TFT LCD HDMI Monitor for Raspberry Pi 3,2 and RPi 1 Model B B+
₱ 3,055.00
Lazada
Go to Shop
−4%
SunFounder Rotary Encoder Module for Arduino and Raspberry Pi - Int'l
₱ 709.00 ₱ 744.00
Lazada
Go to Shop
SunFounder Breadboard Power Supply Solderless Module for Arduino and Raspberry Pi, MB102 3.3V 5V Compatible with UNO R3 Mega2560 Nano Raspberry Pi 3, 2 Model B & Raspberry Pi 1 Module B+
₱ 923.00
Galleon

Introduction This is a power supply module designed for MB102 breadboards. It is powered by a 5V DC jack with an input voltage of 6.5v-12V. The module has a power button and power indicator LED on board. When you press the power button, the LED will brighten and the module starts working. The module supports output of 3.3V or 5V. Two circuits are set at top and bottom for separated control and output can be changed between 0V, 3.3V and 5V. You can connect the two rows of pins on the module for 3.3V/5V output, and the 5V USB Type-A port can be used to supply the MCU. With this power module, you can do experiments and start learning in a more convenient and simpler way! Note: The module needs an input of 6.5V-12V. If a lower voltage like 5V is provided, you can't get a 5V output, because there should be a voltage difference between input and output, otherwise the module cannot work. Breadboard NOT included.

Read more
Go to Shop
−4%
SunFounder OLED-SSD1306 Module - intl
₱ 1,212.00 ₱ 1,273.00
Lazada
Go to Shop
−4%
SunFounder Sound Sensor Module for Arduino and Raspberry Pi - Int'l
₱ 632.00 ₱ 663.00
Lazada
Go to Shop
SunFounder Raspberry Pi 3 Zero Starter kit - Project Super Kit V3.0for Raspberry Pi 3 2 Zero Model B+ A+ Including GPIO Breakout BoardBreadboard LCD DC Motor RGB Matrix 123 Page Manual User Guide
₱ 5,384.00
Lazada
Go to Shop
SunFounder 37 Modules Sensor Kit V2.0 for Raspberry Pi 3, 2, Zero & RPi 1 Model B+, A+ 40Pin GPIO Extension Board Jump wires
₱ 8,129.00
Galleon

This NEW Sensor Kit V2.0 for Raspberry Pi B+ is a revision based on the previous version Sensor Kit for Raspberry Pi B+. Most of the experiments are the same between the two. The key difference lies in the code and Fritzing breadboard images which are changed greatly in the new version - SunFounder has redesigned the modules to be really utilized in this kit, and to keep the same experimental phenomenon we revised the code and images accordingly. The changes are obvious to be noticed. 35 lessons in the 168-page User Manual, paper version included in the package when the PDF version offered on our website. Also the detailed materials of each module, including the code in Python and C and Fritzing images, are provided for you to learn its applications easily; you may find the datasheet of the modules in the WIKI section on our website. 35 Lessons 1 Dual-Color LED 2 RGB LED Module 3 7-Color Auto-flash LED 4 Relay Module 5 Laser Emitter Module 6 Button Module 7 Tilt

Read more
Go to Shop
SunFounder 10.1 Inch IPS HDMI Monitor 1280*800 HD LCD ScreenDisplay Audio For Raspberry Pi 3 2 Model B+
₱ 5,829.00
Lazada
Go to Shop
SunFounder 5V Solid State Relay Board for Arduino (2-Channel)
₱ 1,216.00
Galleon

Input part: DC +: connected to positive power source (supply power according to the relay voltage) DC -: connected to negative power source CH1: 1-channel relay module signal triggering end (effective at low level) CH2: 2-channel relay module signal triggering end (effective at low level)

Read more
Go to Shop
SunFounder TTL 3DR Radio Telemetry Kit 915Mhz Module for Quadcopter Multirotor APM 2.5 2.6 2.8
₱ 3,004.00
Galleon

Introduction The 3DR Radio telemetry system is designed as an open source Xbee replacement radio set, offering a lower price, longer range and superior performance to Xbee radios.The SiK firmware includes a bootloader that permits radio firmware upgrades over the serial interface, and radio firmware with configurable parameters. Air Radio Module is used for UAV or equipment or aerial work equipment. Ground Radio Module is used to connect to a computer or display images on other equipment in the ground. When two modules are bound with the wireless signal, we can use the APM ground station(Mission Planner) to adjust and upgrade the parameters. Component List 1 x Air Radio Module 1 x Ground Radio Module(USB dongle) 1 x cable 30cm long 2 x bendable whip antenna

Read more
Go to Shop
SunFounder Raspberry Pi Retro Game Box DIY Arcade Fighting Joystick Push Buttons Controller for RetroPie Raspberry Pi 3/2/B+ with TF 8g Card
₱ 4,259.00
Galleon

Introduction Retro Game Box is generally a game controller, which implements control by GPIOs of the Raspberry Pi. It comes with a pretty and solid paper box, and needs just simple assembly before easy play with comfortable joystick and concave arcade buttons. Just connect the Raspberry Pi and Retro Game Box to a monitor, and then you can play various classic retro games with this box like Super Mario, Contra, etc. The joystick on the left is for direction control, while on the right are the function buttons, same arrangement with your gamepad. Thus no detailed instructions are needed. You can play it with RetroPie for the Raspberry Pi. This amazing box can bring you the joy of retro games in childhood. Now go get one for crazy play! Vidoe for reference: https://www.youtube.com/watch?v=f8PVFJiWC-k&feature=youtu.be Specifications Dimensions: 25.5 x 15 x 14.5cm (joystick included) Package Included 1 x Arcade Joystick Kit (screws and fixing plates included) 6 x Arcade Buttons 1 x Paper Box 1 x 8G Micro SD Card 1 x Raspberry Pi GPIO Reference Card 1 x Guide Brochure Several Wires

Read more
Go to Shop
SunFounder PL2303HX USB to Serial UART Mini Converter Board Module for Arduino USB to TTL TTL to USB Raspberry Pi APM CC3D MWC FPV MCU
₱ 1,146.00
Galleon

Introduction This PL2303 Mini USB to UART board is a converter module which is a perfect choice when you want to use a serial port for a module that lacks the function. It includes a powerful converter PL2303 and 3 indicator LEDs and connects to other modules with a mini USB port. Pin Description TXD: Transmitting terminal of the converter module, normally connected to RXD of another device RXD: Receiving terminal of the converter module, normally connected to TXD of another device GND: ground, connected to GND VCC: 5V output; if you connect a 3.3V device, you need to use a power adapter to step down voltage DTR: Data Terminal Ready, active low CTS: Clear To Send, active low Package included: - 1 * PL2303HXD Module

Read more
Go to Shop
SunFounder Project Super Starter Kit V3.0 with Tutorial Book for Arduino - intl
₱ 2,317.00
Lazada
Go to Shop
−4%
SunFounder Infrared-Receiver Module for Arduino and Raspberry Pi - Int'l
₱ 709.00 ₱ 744.00
Lazada
Go to Shop
SunFounder USB 2.0 Mini Microphone for Raspberry Pi 3, 2 Module B & RPi 1 Model B+/B Laptop Desktop PCs Skype VOIP Voice Recognition Software
₱ 749.00
Galleon

Introduction This is a tiny USB Microphone that plugs into your Raspberry Pi, laptop or desktop computer. No microphone on your computer? No problem - just plug this incredibly small microphone into a USB port and add microphone functionality. No need to install any extra software; Raspberry Pi / Microsoft Windows will detect the device and automatically install it. Simply launch within any program such as Skype or Google Hangouts. Please Note : best used in a port that's not near your computer's cooling fan. Package list 1 x USB Microphone

Read more
Go to Shop
SunFounder Ultimate Sensor Kit for Arduino UNO R3 Mega2560 Mega328 Nano Including 98 Page Instructions Book
₱ 5,564.00
Galleon

The kit is special in consisting mainly of sensor modules. Each sensor is made in the format of module which integrates some necessary components, such as comparator, resistor, and capacitor and so on, so it's convenient for circuit connection. This kit can help you "control" the physical world with sensors. Code, Fritzing files and datasheets are free to view and download under the LEARN section on SunFounder website. 36 Experiments with Modules Lesson 1 Display by I2C LCD1602 Lesson 2 Analog Hall Sensor Lesson 3 Switch Hall Sensor Lesson 4 Analog Temperature Sensor Lesson 5 Temperature Detection by Thermistor Lesson 6 Auto-flash LED Lesson 7 Barometer Lesson 8 Real-time Clock Module Lesson 9 Flame Alarm Lesson 10 Flammable Gas Detection Lesson 11 Humiture Detection Lesson 12 Joystick PS2 Lesson 13 Controlling an LED by Button Lesson 14 Vibration Switch Lesson 15 Touch Switch Lesson 16 Photo-interrupter Lesson 17 Photoswitch Lesson 18 Reed Switch Lesson 19 Relay Lesson 20 Blinking an LED by Potentiometer Lesson 21 Tilt Switch Lesson 22 Buzzer Lesson 23 Digital Temperature Sensor Lesson 24 Rainbow LED Lesson 25 Infrared Receiver Lesson 26 Dual-color LED Lesson 27 Sound Sensor Lesson 28 Rotary Encoder Lesson 29 Laser Transmitter Lesson 30 IR Tracking Sensor Lesson 31 IR Obstacle Avoidance Sensor Lesson 32 Color Detection Lesson 33 Analog-Digital Converter Lesson 34 Raindrop Detection Lesson 35 Distance Detection by Ultrasonic Lesson 36 Thermostatic Water Tank

Read more
Go to Shop
SunFounder Servo Control Board Wireless Version for Arduino Arduino Nano and NRF24L01
₱ 1,138.00
Galleon

Introduction The expansion board integrates pin sockets for Arduino Nano, NRF24L01 and 12 servos together with a DC-DC circuit. You can use this board to control a robot or some other devices that contain multiple servos. Application It can be used as the servo control board in robot projects. Component List 1 x Servo Control Board Wireless Version Note The supply voltage must be within the limit required.

Read more
Go to Shop
−18%
SunFounder Raspberry Pi Robot Kit Pismart Box - PiSmart Box Speech Recognition Control Driving 8 Servos 2 Motors Visual Programming Language Software with Raspberry Pi 3 Model B - intl
₱ 20,965.00 ₱ 25,791.00
Lazada
Go to Shop
SunFounder Starter RFID Learning Kit for Arduino Beginner withManual - intl
₱ 3,525.00
Lazada
Go to Shop
SunFounder USB Mini Microphone Audio Adapter for Laptop Desktop PCsSkype VOIP Voice Recognition Software - intl
₱ 300.00
Lazada
Go to Shop
SunFounder Full Color RGB LED Matrix Driver Shield + RGB Matrix Screen for Arduino
₱ 1,953.00
Galleon

Introduction Support power supply by SunFounder/Arduino/other compatible Uno board or an external independent source Display characters of a normal format and also contra-rotating 90 degrees Component List 1 * RGB dot matrix screen 1 * RGB Dot Matrix Driver Shield Note: 1)The shield only supports a common-anode LED dot matrix screen 2)The shield itself does not support any functions; it needs to be plugged onto a Uno board for normal use.

Read more
Go to Shop
SunFounder RollbotMicro STEM Learning Educational DIY Robotics KitGUI-Mixly for Arduino Beginner - intl
₱ 3,784.00
Lazada
Go to Shop
−4%
SunFounder Photoresistor Sensor Module for Arduino & Raspberry Pi - Int'l
₱ 709.00 ₱ 744.00
Lazada
Go to Shop
SunFounder Solderless Breadboard Prototype PCB Board MB102 830 Tie-Points + Male to Male Jumper Wires Flexible 65pcs
₱ 1,030.00
Galleon

Introduction The breadboard allows you to easily plug in and remove components and so if there are going to be many changes or if you just want to make a circuit quickly, it will be much quicker than soldering up your circuit. Besides, multiple breadboards of the same size can be combined by parallel horizontally or vertically. Breadboards can be used for numerous times so they are environmentally-friendly. Jumper wires are basic component that connects two or more devices. They are produced in many colors so you can easily pick up the right one when lots are plugged. Package included 1 x 830-hole Solderless Breadboard 65 x Jumper Wires

Read more
Go to Shop
−4%
SunFounder Relay Module for Arduino & Raspberry Pi - Int'l
₱ 632.00 ₱ 663.00
Lazada
Go to Shop
−4%
SunFounder Barometer-BMP180 Module for Arduino and Raspberry Pi - Int'l
₱ 926.00 ₱ 972.00
Lazada
Go to Shop
SunFounder 37 Modules Sensor Kit V2.0 for Raspberry Pi RPi 1 Model B, 26-Pin GPIO Extension Board Jump wires Including 155 Page Instructions Book
₱ 7,867.00
Galleon

Introduction The kit is special in consisting mainly of sensor modules. Each sensor is made in the format of module which integrates some necessary components, such as comparator, resistor, and capacitor and so on, so it's convenient for circuit connection. This kit can help you "control" the physical world with sensors. Code, Fritzing files and datasheets are free to view and download under the LEARN section on SunFounder website. 35 Experiments Lesson 1 Dual-Color LED Lesson 2 RGB LED Module Lesson 3 7-Color Auto-flash LED Lesson 4 Relay Module Lesson 5 Laser Emitter Module Lesson 6 Button Module Lesson 7 Tilt-Switch Module Lesson 8 Vibration Switch Lesson 9 IR Receiver Module Lesson 10 Buzzer Module Lesson 11 Reed Switch Lesson 12 Photo-interrupter Lesson 13 PCF8591 Lesson 14 Rain Detection Module Lesson 15 Joystick PS2 Lesson 16 Potentiometer Module Lesson 17 Hall Sensor Lesson 18 Temperature Sensor Lesson 19 Sound Sensor Lesson 20 Photoresistor Module Lesson 21 Flame Sensor Lesson 22 Gas Sensor Lesson 23 IR Remote Control Lesson 24 Touch Switch Lesson 25 Ultrasonic Ranging Module Lesson 26 DS18B20 Temperature Sensor Lesson 27 Rotary Encoder Module Lesson 28 Humiture Sensor Lesson 29 IR Obstacle Avoidance Module Lesson 30 I2C LCD1602 Lesson 31 Barometer Lesson 32 MPU6050 Gyro Acceleration Sensor Lesson 33 RTC DS1302 Lesson 34 Tracking Sensor Lesson 35 Intelligent Temperature Measurement System

Read more
Go to Shop
SunFounder Remote Control Robot Smart Car Kit V2.0 for Arduino Uno R3 Ultrasonic Line Follower Sensor IR Receiver - intl
₱ 10,521.00
Lazada
Go to Shop
−4%
SunFounder Flame Sensor Module for Arduino and Raspberry Pi - Int'l
₱ 709.00 ₱ 744.00
Lazada
Go to Shop
SunFounder EF-01 FPV Micro AIO Camera 40CH Transmitter Combo for Blade Inductrix Indoor FPV Racing Quadcopter Drone
₱ 1,760.00
Galleon

Introduction The EF-01 AIO FPV camera realize 25mW 40ch 5.8GHz TX, circular polarization clover leaf antenna and great CCD killer 800TVL FPV camera all 3 functions in one limit size and weight unit. Aluminum case and easy mounting design make it great for smaller scale FPV race drones. It's perfect for NTSC and PAL as built-in one button switch. Product Specification: Sensor :1/3 Lens :M8 800TVL Lens Angle :150° FOV horizontal viewing angle of 170° DFOV diagonal perspective Format :NTSC / PAL (switchable) Power consumption :380mA 3.7V Power Range :3.6-5.5V Lens Mirror Diameter :2.1mm IR coated FOV150 (horizontal) Video Transmitter :25MW VT Wireless Channel :40CH Antenna :RHCP circular polarization clover leaf antenna Current :100mA Weight: 8g Size: 26x20x18mm (without antenna) Button function: Short press (Apr. 1 sec or less): Change channels 1-8 Long press (More than 1.5 sec): Change bands A-B-E-F-R Long + press (More than 3 sec): Change NTSC/PAL system NTSC or PAL (selectable; Blue LED on= NTSC; Blue LED off=PAL) Package List 1 * EF-01 AIO FPV Camera 1 * Cable 1 * User manual

Read more
Go to Shop
−4%
SunFounder Mercury Switch Module for Arduino and Raspberry Pi - Int'l
₱ 535.00 ₱ 561.00
Lazada
Go to Shop
SunFounder Electronics Base Kit EC-Block Electronic Building Block for ArduinoStarter Kit for Kids to Learn &Understand Physical Principle -intl
₱ 3,009.00
Lazada

SunFounder Online Store Philippines

Some of the most prominent products in the market from SunFounder come in Blue and Black. Shop at iprice and find some great deals for SunFounder of up to 55% discount! Obstacle Avoidance Sensor Module for Arduino and Raspberry Pi, Starter Learning Kit V2.0 for Arduino Beginner fromKnowing to Utilizing With UNO R3 Board - intl and Flame Sensor Module for Arduino and Raspberry Pi are three of the most in demand products from SunFounder. If you only have ₱ 300.00 to ₱ 25,774.00 to spend, then you can surely get your hands on some of the best SunFounder products online! Ranging from different accessories and apparels like Computing, Lighting and Home Office, SunFounder has you