Product Categories
Go to top
196 products found
Go to Shop
yonico Yonico 13124 Double Roman Ogee Edging Router Bit Large 1/2-Inch Shank
₱ 1,389.00
Galleon

Cut moldings, picture frames, table edges and more in a beautiful double roman ogee design . Two flute carbide cutters with ball bearing guide. 1/2" shank. 3/4" Cutter Height, 9/16" Cutter Depth.

Read more
Go to Shop
yonico Yonico 12339q Rail and Stile with Panel Raiser Router Bit Set Cove 1/4-Inch Shank, 3-Piece
₱ 5,961.00
Galleon

The Yonico 12339q Door Construction Router Bit Set includes 1/4" round over rail and stile bits and a 1/4" cove panel raiser. For use with up to 1" stock. Router Bit Measurements: • Rail & Stile - 1-3/4" Diameter, 1" cutter height, 2-7/8" overall height, 3/8" depth of cut, 7/8" bearing diameter • Panel Raiser - 2-1/2" diameter, 1/2" cutter height, 2-7/16" overall height, 1" depth of cut, 1/2" bearing diameter Rail and stile bits create a perfectly matched rail and stile door frame. The cove raised panel router bit cuts a stylish edge on the central panel of your door. Ball bearing guides allow you to make precise cuts without the use of a fence. The Yonico 12339q router bit set comes in a solid wood storage case. Bit shanks are 1/4".

Read more
Go to Shop
yonico Yonico 14220 Solid Carbide Flush Trim Spiral Router Bit Set, 1/4"
₱ 4,184.00
Galleon

This solid carbide flush trim router bit set includes one up cut spiral flush trim bit and one down cut spiral flush trim bit. They are designed to provide precise, efficient cuts and offers extreme durability. The spiral design effectively reduces chipping. For use with soft & hard woods, ply-woods, composites, laminates, plastics and some non-ferrous metals. The two independent ball bearings with forced on steel collars at the tip of each bit ensures smooth worry free use. 1/4" shanks.

Read more
Go to Shop
yonico Yonico 31011-SC O-Flute Up Cut Solid Carbide CNC Router Bit, 1/8 x 1/2 x 1/4 x 2"
₱ 1,368.00
Galleon

Best used for: Aluminum • Cutting Diameter: 1/8" • Cutting Height: 1/2" • Shank Diameter: 1/4" • Overall Length: 2" • Flutes: 1 This bit is specifically designed for milling aluminum. O flute end mills allow for lots of chip clearance which is essential when milling aluminum. Aluminum creates larger chips than most other materials and bits such as O-flute end mills are recommended for proper chip removal.

Read more
Go to Shop
yonico Yonico 15336 Jointing Router Bit Set, 3-Piece
₱ 6,463.00
Galleon

The Yonico 15336 Joint making Router Bit Set includes 3 of the most popular joint making router bits. Two flute carbide cutters & 1/2" shanks. Set comes in a solid wood storage case. Includes the following 3 bits: 1 - Medium 45 Degree Lock Miter Bit - Use the reversible 45° lock miter bit to join boards at 90°. The interlocking 45° cuts will produce extremely strong joints without having to struggle to keep the boards in place during clamping. Additionally, it will provide extra gluing surface resulting in an extremely strong and durable joint. When positioned properly, the bit will cut both pieces of stock without having to adjust the bit. Simply set the center of the bit to the center of the stock. Then, cut one piece horizontally and the second one vertically. Use with 3/4" stock. 2 - Medium Reversible Glue Joint Bit - Rout perfect joining cuts with one reversible bit. Simply set the center of the bit with the center of the stock. Run one cut face up and the adjoining cut face down. Great for edge-joining tabletops, door panels and flooring among many other board to board joint projects. 3 - Reversible Drawer Lock Bit - Produce strong, long-lasting joints for gluing the front and sides of drawers. This bit can also make drawer slides.

Read more
Go to Shop
yonico Yonico 14801 Luthier's 8 Bit Essential Router Bit Set, 1/2"
₱ 7,894.00
Galleon

The Yonico 14801 Luthier's Electric Guitar Router Bit Set includes all the essential router bits needed for electric guitar body making. This set will enable you to: • Flush trim the guitar body• Add a round over to the body's edge • Rabbet the body's edge for binding • Groove out the cavities • Bevel the pick guard • Cut intricate inlays This set includes: • 1 Top and bottom bearing flush trim router bit Yonico 14134 - 2" Top and Bottom Bearing Flush Trim Router Bit • 1 Round over router bit & 13162 - 1/4" Radius Round Over Router Bit • 1 Rabbet router bit - Yonico 14187 1/2" High X 3/8" Deep Rabbeting Router Bit • 3 Additional Bearings: Outer Diameter - 5/8" for 5/16" Binding & Diameter - 3/4" for 1/4" Binding & Diameter - 7/8" for 3/16" Binding • 1 3/4" X 3/4" Bottom cleaning router bit & 14971- 3/4" X 3/4" Bottom Cleaning Long Shank Straight Router Bit • 2 template trim router bits & 14123q - 1/2" Wide X 3/4" High Template Trim Router Bit & 14169q - 1/2" Wide X 1/2" High Template Trim Router Bit • 1 Bevel trim router bit & 14932q - 30° Bevel Trim Router Bit • 1 Down cut solid carbide spiral router bit & 32210-SC - 1/8" Diameter Downcut Spiral Solid Carbide Router Bit Please note: This set includes bits that are 1/2" shank and 1/4" shank.

Read more
Go to Shop
yonico Yonico 14525q 5 Bit Pattern/Template Flush Trim Router Bit Set, 1/4-Inch Shank
₱ 2,631.00
Galleon

The Yonico 14525q 5 bit set includes an assortment of pattern/template router bits for sign making, lettering and various other uses. Set includes: • 90° V-Groove Template Bit - 1/2" Width X 5/8" Height, • Round-nose Template Bit - 1/2" Width X 5/8" Height, • Bowl Template Bit - 3/4" Width X 5/8" Height, • Hinge Mortise Template Bit - 3/4" Width X 1/4" Height, • Straight Template Bit - 5/8" Width X 3/4" Height, All bits in this set feature center meeting blades for a perfectly smooth finish. Carbide tipped and 1/4" shanks.

Read more
Go to Shop
yonico Yonico 17504 50 Bits Professional Quality Router Bit Set C3 Carbide 1/4-Inch Shank
₱ 12,814.00
Galleon

Included in this incredible set are 50 professional quality router bits, manufactured with K-10 carbide cutters and ultra sharp blades for the price of only several single router bits! These bits are of the quality sold in stores for $10- $25 a piece! K-10 is a premium micro-grain carbide with outstanding abrasion resistance and high strength for longer cutting life. Bits are precision balanced to within .002" to virtually eliminate vibrations. Fully enclosed, high quality lubricated bearings will ensure smooth operation. In addition, heat resistant coating is baked on to prevent pitch and resin build-up. Beautiful solid wood storage case included. Choose between 1/2" or 1/4" shanks.

Read more
Go to Shop
yonico Yonico 14984 Large Ogee Groove Router Bit with CNC and Plunge 1/2-Inch Shank
₱ 1,866.00
Galleon

The Yonico 14984 features center meeting blades for all plunging applications. The ogee design is great for faux panel doors and shallow bowling. Can be used in CNC.FeaturesIndustrial QualityC3 Tungsten Carbide CuttersSolid Hardened Steel BodyAnti-Kickback DesignBuild-Up Resistant Coating1/2"; ShankSatisfaction Guaranteed

Read more
Go to Shop
yonico Yonico 14188 T-Slot and T-Track Slotting Router Bit 1/2-Inch Shank
₱ 1,947.00
Galleon

The Yonico 14188 T-Track Router Bit cuts T-slots for T-track bolts with 1-1/16" wide x 5-16" high bolt heads and up to with 3/8" shaft thickness. Can also be used to make slat wall boards. Features • Industrial Quality • C3 Tungsten Carbide Cutters • Solid Hardened Steel Body • Anti-Kickback Design • Build-Up Resistant Coating • Satisfaction Guaranteed.

Read more
Go to Shop
yonico Yonico 12243 Rail and Stile Router Bits with Matched 2 Bit Standard Ogee 1/2-Inch Shank
₱ 3,929.00
Galleon

Yonico rail and stile router bit set (12243) will cut both stile and rail for cabinet doors in the classic ogee design. Use the ogee rail and stile bits with up to 1" stock. Fully enclosed ball bearing guides allow for precise routing without the use of a fence. Two flute carbide cutters & 1/2" shanks. Rail and stile set comes in a solid wood storage case. Complete your doors from our selection of Yonico panel raisers giving it an enhanced finish. Yonico router bits are manufactured with C3 micrograin carbide, producing precision work and a smooth, detailed finish.

Read more
Go to Shop
yonico Yonico 32211-SC CNC Router Bit Down Cut Solid Carbide with 1/4-InchX 3/4-Inch X 1/4-Inch X 2-1/2-Inch 1/4-Inch Shank
₱ 1,368.00
Galleon

Best used for: Laminate or veneer-finish plunging and dadoing.• Cutting Diameter: 1/4" • Cutting Height: 3/4" • Shank Diameter: 1/4" • Overall Length: 2-1/2" • Flutes: 2 Down cut endmills shear in a downward direction causing the uppermost layer of the material to be pressed down against the material just below it. This motion leaves a perfectly clean top surface edge. A concentration of wood chips in the work path will occur. Hose away excess wood chips to prevent bit breakage.

Read more
Go to Shop
yonico Yonico 18226 2 Bit Handrail Router Bit Set with Thumbnail Bead/Bead 1/2-Inch Shank
₱ 3,773.00
Galleon

Create railings and handrails with this 2 bit router bit set. The profile bit will cut both sides of the handrail and the thumbnail bit will round the top for a smooth finish. The thumbnail bit can also be used for table edging among other projects. Set includes a beautiful solid wood storage case. Two flute carbide cutters & 1/2" shanks.

Read more
Go to Shop
yonico Yonico 33210-SC Yonico 33210-SC CNC Router Bit 2 Flute Compression Cut 1/4" X 1" X 1/4" X 2-1/2" 1/2" Shank, ,
₱ 2,079.00
Galleon

Best for achieving a smooth finish on laminate or veneer finish applications.• Cutting Diameter: 1/4" • Cutting Height: 1" • Shank Diameter: 1/4" • Overall Length: 2-1/2" • Flutes: 2 Compression bits cut down from the top of the stock and up from the bottom of the stock simultaneously. The bit's unique and complex geometry forces the trimmed material to be compressed toward the center of the stock leaving behind a smooth & sharp finish free of chips on both the top and bottom edges. This bit can also be used for mortising projects that require a smooth bottom surface without sacrificing the mortised edge finish.

Read more
Go to Shop
yonico Yonico 16181 Bowl & Horizontal Crown Router Bit 2" Radius 1/2" Shank
₱ 1,927.00
Galleon

This bowl and horizontal crown bit features a radius and cutting diameter of 2" with a total cutting depth of 33/64". the shank is 1/2" in diameter. Horizontal crown router bits, also referred to as large bowl router bits, create large spherical indents in a variety of materials and can be plunged straight into the work piece. These are perfect for making large custom crown moldings, bowls, coin Trays, mA Nc all a game boards and other interesting projects. These can be used on solid wood and MDF.

Read more
Go to Shop
yonico Yonico 14520 5 Bit Dovetail Router Bit Set, 1/2-Inch Shank
₱ 3,130.00
Galleon

The Yonico 14520 5 Bit Dovetail Router Bit Set contains 5 common dovetail bit sizes and angles needed for most dovetail projects. Can be used with a dovetail jig for half-blind dovetail joints or can be used together with dado bits to produce through-dovetail joints.

Read more
Go to Shop
yonico Yonico 12135 Raised Panel Router Bit with Backcutter Cove 3-1/4-Inch Diameter 1/2-Inch Shank
₱ 3,140.00
Galleon

The Yonico Cove Panel Raiser Router Bit with Back cutter will cut cove raised panels easily while reducing the tongue thickness to 1/4". Use with 5/8"-1" stock. Two flute carbide cutters and 1/2" shank. • Back cutter - 2" Diameter x 1/4" Cutter Height • Front Cutter - 3-1/4" Diameter x 9/16" Cutter Height.

Read more
Go to Shop
yonico Yonico 12164 Drawer and Cabinet Door Front Edging Classical Router Bit 1/2-Inch Shank
₱ 1,831.00
Galleon

Add a classical ogee edge to your drawer and cabinet door fronts using this Yonico 12164 edging router bit. 1/2" Shank.

Read more
Go to Shop
yonico Yonico 12238q Rail and Stile Router Bits with 2 Bit Round Over 1/4-Inch Shank
₱ 3,521.00
Galleon

Yonico rail and stile router bit set (12238q) will cut rail & stile for cabinet doors in a classic round over design. Fully enclosed ball bearing guides allow for precise rail and stile cuts without the use of a fence. Two flute carbide cutters & 1/4" shanks. Yonico rail and stile router bits produce impressive and perfect results with every cut yielding years of woodworking satisfaction.

Read more
Go to Shop
yonico Yonico 14171 Mortise/Template Trim Router Bit with Bottom Cleaning 1/2-Inch Shank
₱ 1,831.00
Galleon

Yonico 14171 Mortising Router Bit will route clean cutouts for hinges or other shallow cutout projects. Shank bearing ideal for use with a hinge template. Center meeting blades leave behind a perfectly clean routed area. Two flute carbide cutters with 1/2" shank.

Read more
Go to Shop
yonico Yonico 12134 Base Board/Panel Raiser Ogee Router Bit with 2-1/2-Inch Diameter 1/2-Inch Shank
₱ 2,038.00
Galleon

This versatile 2-1/2"; diameter router bit can be used to make beautiful ogee design baseboards as well as raised panels for cabinet doors. Ogee design baseboards add beauty and style to any decor. When used as a panel raiser, this 2-1/2"; router bit will create door panels with a smaller than standard profile. You may use in conjunction with any of our rail and stile router bits. Two flute carbide cutters & 1/2"; shank.FeaturesIndustrial QualityC3 Tungsten Carbide CuttersSolid Hardened Steel BodyAnti-Kickback DesignBuild-Up Resistant CoatingSatisfaction Guaranteed

Read more
Go to Shop
yonico Yonico 13108 1/4-Inch Radius Corner Bead/Beading Router Bit 1/2-Inch Shank
₱ 1,494.00
Galleon

Put a 1/4" radius corner bead to your project using the Yonico 13108 corner bead router bit. Set bottom of radius even with the table top surface and the bearing flush with the fence. Rout a corner then flip over work piece length wise and rout corner again to finish off the corner bead. 1/2" shank.

Read more
Go to Shop
yonico Yonico 15227 Matched Tongue and Groove V-Notch Router Bit Set 1/2-Inch Shank
₱ 4,142.00
Galleon

This set will cut perfectly fitting (v-groove) tongue & groove joints ideal for flooring and wainscot paneling. Tongue & groove joints give extra gluing surface for extra-strong joints. Use with 5/8" – 1-1/8" stock. Bits are industrial quality and have premium enclosed ball bearings. Set comes in a solid wood storage case. Two flute carbide cutters and shanks are 1/2".

Read more
Go to Shop
yonico Yonico 14177q 1/2" Diameter Offset Flush Trim Template Router Bit with 1/4" Shank
₱ 1,421.00
Galleon

This bit has a cutting diameter of 1/2" and a cutting depth of 1/4". the bearing has a diameter of 5/8" which helps preserve the template. The shank diameter is 1/4". especially designed for hinge Mortising templates, this offset template trim bit will allow you to route corners with radiuses as small as 1/4". the larger bearing distances the blade from the template, shielding it from any unwanted trimming. Offset flush trim router bits are used to get an even smaller corner radius than the shank bearing would normally allow. The cutting diameter is smaller than the bearing diameter and therefore some compensation is required when making your templates. These bits are commonly used for hinge Mortising and small solid body guitar cavities. Flush trim template router bits work in your router Table or handheld router. Secure your template to the top face of the work for handheld operations, or to the bottom face of the work when using a router Table.

Read more
Go to Shop
yonico Yonico 13601 Guitar Finger Board Radiusing Router Bit Set with 1/2" Shank
₱ 8,672.00
Galleon

Replicate the finger board radiuses of all types of iconic guitars including vintage and modern Fender strats, vintage and modern Gibsons, and many others. This set include 6 radiusing bits with the following radiuses: 7-1/4", 8-1/2", 9-1/2", 10", 12" and 16". These bits can accommodate fretboards up to 3-3/4" wide. The bits feature C3 premium micro grain carbide blades and a 1/2" shanks. A unique way to add a radius to your stringed instrument's fretboard. These radiusing bits will eliminate the excessive effort required for using a sanding block. Tape the finger board to a perfectly squared board and slide along the router table fence with the top of the bit's blade running at the height of the center line of the finger board. This will radius one half of the board. Then flip the stock to radius the other half. Yonico fretboard radiusing router bits come in radiuses of 7-1/4", 8-1/2", 9-1/2", 10", 12" & 16".

Read more
Go to Shop
yonico Yonico 32210-SC CNC Router Bit Down Cut Solid Carbide with 1/8-Inch X 1/2-Inch X 1/4-Inch X 2-Inch 1/4-Inch Shank
₱ 1,213.00
Galleon

Best used for: Laminate or veneer-finish plunging and dadoing.• Cutting Diameter: 1/8" • Cutting Height: 1/2" • Shank Diameter: 1/4" • Overall Length: 2" • Flutes: 2 Down cut end mills shear in a downward direction causing the uppermost layer of the material to be pressed down against the material just below it. This motion leaves a perfectly clean top surface edge. A concentration of wood chips in the work path will occur. Hose away excess wood chips to prevent bit breakage.

Read more
Go to Shop
yonico Yonico 13508 5 Bit Chamfer Router Bit Set with 11.25-Degree 15-Degree 22.5-Degree 30-Degree 45-Degree 1/2-Inch Shank
₱ 4,700.00
Galleon

Own this practical 5 bit chamfer router bit set complete with the following 5 chamfer sizes; 11.25°, 15°, 22.5°, 30° and 45°. Router bit dimensions are as follows: • 11.25° Chamfer - 7/8" Diameter, 1" Cutter Height, 2-3/4" Overall Height, 3/16" Cutter Depth • 15° Chamfer - 1" Diameter, 1" Cutter Height, 2-3/4" Overall Height, 1/4" Cutter Depth • 22.5° Chamfer - 1-1/4" Diameter, 1" Cutter Height, 2-13/16" Overall Height, 3/8" Cutter Depth • 30° Chamfer - 1-1/2" Diameter, 1" Cutter Height, 2-3/4" Overall Height, 1/2" Cutter Depth • 45° Chamfer - 1-7/8" Diameter, 23/32" Cutter Height, 2-1/2" Overall Height, 11/16" Cutter Depth The Yonico 13508 router bit set comes in a solid wood storage case. Two flute carbide cutters and 1/2" shanks.

Read more
Go to Shop
yonico Yonico 12338q Raised Panel Cabinet Door Router Bit Set with 3 Bit Ogee 1/4-Inch Shank
₱ 5,961.00
Galleon

Make professional and beautiful raised panel cabinet doors with this 3 piece router bit set. Use with up to 1" stock. Rail & stile bits create a perfectly matched rail & stile door frame. The raised panel bit puts a classic ogee edge on the central panel of your door. The panel raiser can also be used to make attractive drawer fronts, table tops, plaques and moldings. Fully enclosed ball bearing guides allow for precise cuts without the use of a fence. Two flute carbide cutters & 1/4" shanks. Set comes in a solid wood storage case. Included in this set: ogee raised panel bit, 2 bit matched ogee rail & stile, Allen wrench plus extra spacers, solid wood storage case.

Read more
Go to Shop
yonico Yonico 12136 Raised Panel Router Bit with Ogee Door 3-Inch Diameter 1/2-Inch Shank
₱ 2,242.00
Galleon

The Yonico panel raiser router bit 12136 will create beautiful raised panels for cabinet doors in the popular ogee design. Choose from our selection of rail and stile router bits to complete your raised panel doors. Two flute carbide cutters & 1/2" shank.

Read more
Go to Shop
yonico Yonico 14176q Template Trim Hinge Mortising Router Bit 3/4" Wide x 1/4" High 1/4" Shank
₱ 1,676.00
Galleon

This template hinge mortise bit has a 3/4" cutting diameter with a 1/4" cutting depth. This bit's shallow cutting depth and center meeting blades make it perfect for routing door hinge mortises using a hinge template. 1/4" shank. Flush trim template router bits work in your router Table or handheld router. Secure your template to the top face of the work for handheld operations, or to the bottom face of the work when using a router Table. It's helpful to have at least a couple of flush trim bits in different sizes in your router bit Collection. 1/4" and 1/2" diameters make a good combination.

Read more
Go to Shop
yonico Yonico 14972 Bottom Cleaning Dado Router Bit with 7/8-Inch W X 5/8-Inch H 1/2-Inch Shank
₱ 1,874.00
Galleon

Cut perfectly clean 7/8" wide dados with the Yonico 14972 bottom cleaning router bit. The two cutters meet in the center of the bit which leaves behind a very cleanly routed path. Can also be used to clear larger areas of material. 1/2" shank.

Read more
Go to Shop
Yonico 14114 14 degree x 1/2" Dovetail Joint Router Bit with 1/2" Shank
₱ 807.00
Takatack
Go to Shop
yonico Yonico 34221-SC CNC Router Bit Ball Nose Solid Carbide with 1/4-Inch X 1-Inch X 1/4-Inch X 2-1/2-Inch 1/4-Inch Shank
₱ 1,831.00
Galleon

Best used for: Smooth contour milling & carving. Cutting Diameter: 1/4"; Cutting Length: 1";Shank Diameter: 1/4"; Overall Length: 2-1/2"; Flutes: 2The ball nose end mills' rounded tip is designed to reduce tool markings on work pieces of intricate tool paths and varying depths. Larger bits will produce the smoothest results while smaller bits will produce the finest detail.Pros: Produces smooth contours on intricate projects.Cons: Not intended for plunging or dadoing. (Choose a standard spiral bit for general milling, boring and finishing.)For use in CNC milling and carving machines.

Read more
Go to Shop
yonico Yonico 13189q Classical Cove Edging Router Bit with 3/16" Radius and 1/4" Shank
₱ 1,433.00
Galleon

This cove and bead bid can be used as a edging bit as well as a mini crown molding. The bit's cove profile with the added beads will add sleek lines to your project. The Yonico 13189q creates a 3/16" radius cove with beads.

Read more
Go to Shop
yonico Yonico 33230-SC Yonico 33230-SC CNC Router Bit 2 Flute Compression Cut 1/2" X 1-5/8" X 1/2" X 3-1/2" 1/2" Shank, ,
₱ 3,563.00
Galleon

Best for achieving a smooth finish on laminate or veneer finish applications.• Cutting Diameter: 1/2" • Cutting Height: 1-5/8" • Shank Diameter: 1/2" • Overall Length: 3-1/2" • Flutes: 2 Compression bits cut down from the top of the stock and up from the bottom of the stock simultaneously. The bit's unique and complex geometry forces the trimmed material to be compressed toward the center of the stock leaving behind a smooth & sharp finish free of chips on both the top and bottom edges. This bit can also be used for mortising projects that require a smooth bottom surface without sacrificing the mortised edge finish.

Read more
Go to Shop
yonico Yonico 13322q 3 Bit Edge Molding Router Bit Set with Large Designer 1/4" Shank
₱ 2,414.00
Galleon

This set includes a round over bead, a roman ogee and a classical roman ogee profile. These designer profiles all have a cutting depth of 9/16". The round over bead has a 1/2" radius, roman ogee has a 9/32" radius and the classical roman ogee has a 7/32" radius. The shank diameters are 1/4". Edge forming router bits add an artistic profile to the edge of furniture and table tops. Edging router bits can also be used to create small moldings that can be applied to many projects as well as crown molding build-ups. Edge forming router bits come in many shapes and sizes to meet the requirements of any style.

Read more
Go to Shop
yonico Yonico 14182 Biscuit Jointing Router Bit with Number 20 C3 Carbide Tipped 1/2-Inch Shank
₱ 1,751.00
Galleon

Cut slots for # 20 biscuits with the Yonico 14182 slot cutter router bit. 3 wing, professional carbide cutters with enclosed ball bearing guide and 1/2" shank.

Read more
Go to Shop
yonico Yonico 13325 3 Bit Edge Molding Router Bit Set with Ogee 1/2-Inch Shank
₱ 2,567.00
Galleon

The Yonico 13325 includes 3 large traditional edging router bits in the following profiles: Traditional Ogee, Traditional Ogee with Bead and Traditional Classical Ogee. Dimensions are as follows: • Traditional Ogee - 1-1/2" Diameter, 5/8" Cutter Height, 1/2" Cutter Depth • Traditional Ogee with Bead - 1-3/8" Diameter, 37/64" Cutter Height, 7/16" Cutter Depth • Traditional Classical Ogee - 1-1/2" Diameter, 11/16" Cutter Height, 1/2" Cutter Depth Two flute carbide cutters and 1/2" shanks.

Read more
Go to Shop
yonico Yonico 14323 3 Plywood Dado Router Bits for 3/4-Inch 1/2-Inch and 1/4-Inch Plywood 1/2-Inch Shank
₱ 2,541.00
Galleon

This 3 bit Yonico 14323 dado router bit set is guaranteed to make perfect snug fitting dado cuts for the 3 most commonly used sizes of plywood; 3/4", 1/2" and 1/4". Ever try routing a plywood dado joint and discover the cut is too big? Plywood sizes are actually thinner than stated. End the frustration with the Yonico 14323 dado router bit set. New Feature! - The included 1/4" dado router bit is upgraded with a complete solid carbide top and blade as opposed to standard dado router bits which have carbide blades welded on. This vital upgrade prevents otherwise common 1/4" dado router bit breakage. Bits come in a solid wood storage case. All bit shanks are 1/2".

Read more
Go to Shop
yonico Yonico 12238 Rail and Stile Router Bits with Matched 2 Bit Quarter-round 1/2-Inch Shank
₱ 3,773.00
Galleon

Cut rail and stile easily with the Yonico 12238 Quarter Round Rail and Stile Router Bit Set. Two flute carbide cutters & 1/2" shanks. Set comes in a solid wood storage case. Rail and stile bits feature fully enclosed ball bearing guides producing precise cuts without the use of a fence. Manufactured from C3 micrograin carbide, our rail and stile bits make detailed, professional cuts resulting in an impressive finished product.

Read more
Go to Shop
yonico Yonico 31212-SC CNC Router Bit Up Cut Solid Carbide with 3/16-Inch X 3/4-Inch X 1/4-Inch X 2-Inch 1/4-Inch Shank
₱ 1,499.00
Galleon

Best used for: Standard milling, dadoing, and boring.• Cutting Diameter: 3/16" • Cutting Height: 3/4" • Shank Diameter: 1/4" • Overall Length: 2" • Flutes: 2 Up-cut end mills direct woodchips up and away from the milling area leaving an unobstructed path for the endmill. Bit breakage is less likely. Up cut end mills are the best choice for most standard milling applications. The up cut direction can leave behind a minimally rough top surface edge.

Read more
Go to Shop
yonico Yonico 14150 Straight Router Bit with 1/2-Inch X 2-Inch Length 1/2-Inch Shank
₱ 1,346.00
Galleon

Use this versatile 2" extra long cutter router bit for all straight cut needs. Two flute carbide cutters and 1/2" shank.

Read more
Go to Shop
yonico Yonico 14318 3 Bit Dovetail Router Bit Set with 10-Degree and 14-Degree 5/16-Inch Straight 1/2-Inch Shank
₱ 1,907.00
Galleon

This 3 bit dovetail set is the perfect set for those just starting out with dovetail joinery. This set contains the necessary bits to create half blind and through dovetail joints. Straight Bit - 5/16" W x 1" H 10° Dovetail Bit - 1/2" W x 1/2" H 14° Dovetail Bit - 9/16" W x 9/16" H.

Read more
Go to Shop
yonico Yonico 12346 Classical 3 Bit Extended Tenon Entry Door Rail and Stile Router Bit Set with 1/2" Shank
₱ 9,529.00
Galleon

This 3 bit Ogee entry door router bits set can cut rails and stiles between 1-3/4" and 1-3/8" thick. The cutting depth is 1/2" and the shank diameter is 1/2". create extra strong entry and passage doors with the extended tenon entry door router bit set. Aside from the standard rail and stile bits that are included in all entry door sets, this set comes with an additional bit that allows you to create larger Tenons and then cope the profile to match the stile. These bits are very large and robust. A sturdy setup is strongly recommended.

Read more
Go to Shop
yonico Yonico 33310-SC 3 Flute Compression Cut CNC Router Bit, 1/4 x 1 x 1/4 x 2-1/2"
₱ 2,609.00
Galleon

Best for achieving a smooth finish on laminate or veneer finish applications.• Cutting Diameter: 1/4" • Cutting Height: 1" • Shank Diameter: 1/4" • Overall Length: 2-1/2" • Flutes: 3 Compression bits cut down from the top of the stock and up from the bottom of the stock simultaneously. The bit's unique and complex geometry forces the trimmed material to be compressed toward the center of the stock leaving behind a smooth & sharp finish free of chips on both the top and bottom edges. This bit can also be used for mortising projects that require a smooth bottom surface without sacrificing the mortised edge finish.

Read more
Go to Shop
yonico Yonico 16138 Architectural Molding Router Bit 1/2-Inch Shank
₱ 1,757.00
Galleon

Add dramatic ‘English and Colonial’ beauty. Ideal for trimming large and small furniture, cabinet doors and countertops. Great for chair rails, crown moldings, baseboards and any dramatic furniture design. Will cut large picture frames as well. Two flute carbide cutters with ball bearing guides. 1/2" shank. Can also be purchased as part of a 10 piece molding set (item #16101).

Read more
Go to Shop
yonico Yonico 15221q Tongue and Groove Router Bit Set with 3/4-Inch Stock 1/4-Inch Shank
₱ 4,141.00
Galleon

Cut perfectly fitted tongue and groove joints ideal for wood flooring, wainscot paneling and shaker style panel doors. Set includes separate tongue and groove bits eliminating reassembly for each cut. Use with 3/4" stock. Highest quality, 3 wing carbide cutters. Fully enclosed ball bearing guides. 1/4" shank.

Read more
Go to Shop
yonico Yonico 31413-SC 1/8" diameter 4 Flute Upcut Spiral ZRN Coated CNC Router Bit with 1/4" Shank
₱ 1,499.00
Galleon

This ZRN coated end mill has a 1/8" cutting diameter x 1-1/4" cutting length. The overall length is 2-1/2" with a 1/4" shank. Up cut end mills are great for all standard milling and material removal. With the added ZRN coating, the bit’s lifespan and durability are increased substantially avoiding unnecessary down time. These bits pull the wood chips up and away from the tool path which helps prevent tool breakage and extends the life of the bit. If a particular finish is required for your project, use a down cut or compression cut end mill for the final pass.

Read more
Go to Shop
yonico Yonico 14161q Core Box Router Bit Long Reach 1/4"W X 5/16"H 1/4" Shank
₱ 1,287.00
Galleon

Designed for sign making and general round nose grooving. With an overall height of 2-3/8" and 1/8" radius, the Yonico 14161q router bit is ideal for long reach core box grooving. Two flute carbide cutters and 1/4" shank.

Read more
Go to Shop
yonico Yonico 13107 45-Degree Chamfer/Bevel Edging Router Bit with X-Large 1/2-Inch Shank
₱ 1,802.00
Galleon

• Industrial Quality • C3 Carbide Cutters • Solid Hardened Steel Body • Anti-Kickback Design • Build-Up Resistant Coating • 1/2" Shank Make 45° bevel cuts with the Yonico 13107 Chamfer Router Bit. Bevel height is 9/16". Two flute carbide cutters and 1/2" Shank.

Read more
Go to Shop
yonico Yonico 36314-SC CNC Router Bit Low Helix Down Cut Long Reach 1/4" x 1" x 1/4" x 2-1/2" 1/4" Shank
₱ 2,878.00
Galleon

Best for achieving smooth finish on hard plastics.• cutting diameter: 1/4" • cutting height: 1" • shank diameter: 1/4" • overall length: 2-1/2" • flutes: 3 low helix bits perform a more lateral movement with less upward or downward motion resulting in a smoother finish on single layer materials. These bits are a better choice for hard plastics such as acrylic and phenolic. Down cut end mills Shear in a downward direction causing the uppermost layer of the material to be Pressed down against the material just below it. This motion leaves a perfectly clean top surface edge. A concentration of wood chips in the work path will occur. Hose away excess wood chips to prevent bit breakage.

Read more
Go to Shop
yonico Yonico 18322 Complete Picture Frame Making Router Bit Set with 1/2-Inch Shank
₱ 4,365.00
Galleon

An absolute necessity for picture frame making, this set includes 3 bits that will cut you through every step of the process with ease! Choose between the 2 included profiles for your frame design and then use the stepped bit to rabbet the back. You may also combine both profiles for a unique look by cutting the inner part of the frame with the smaller bit and the outer part of the frame with the larger bit. Rabbeting the back of the frame will allow ample space for your artwork, glass and backing. The double stepped rabbet will cut a 3/16"; x 5/16"; front rabbet for your glass or mirror, and an additional 9/32"; x 3/8"; back rabbet for the artwork and backing board. Set includes a beautiful solid wood storage case. Two flute carbide cutters & 1/2"; shanks.

Read more
Go to Shop
yonico Yonico 15221 Matched Tongue and Groove Router Bit Set 1/2-Inch Shank
₱ 3,773.00
Galleon

Cut perfectly fitted tongue and groove joints ideal for wood flooring, wainscot paneling and shaker style panel doors. Set includes separate tongue and groove bits eliminating reassembly for each cut. Use with 3/4" stock. Highest quality, 3 wing carbide cutters. Fully enclosed bearing guides. 1/2" shank.

Read more
Go to Shop
yonico Yonico 14170q Hinge Mortise/Template Router Bit with 3/4-Inch X 7/16-Inch 1/4-Inch Shank
₱ 1,749.00
Galleon

Yonico 14170q Hinge Mortising Router Bit will rout clean cutouts for hinges or other shallow cutout projects. Shank bearing ideal for use with a hinge template. Center meeting blades leave behind a perfectly clean routed area. Two flute carbide cutters with 1/4" shank.

Read more
Go to Shop
yonico Yonico 12222 11/32" Radius Ogee 2 Bit Matching Entry Door Profile Router Bit Set with 1/2" Shank
₱ 3,803.00
Galleon

Add a beautiful Ogee profile to the inner edge of mortise and tenon entry doors. This set features a cutting height of 5/8", cutting depth of 5/8" and a traditional Ogee design with 5/16" radiuses. 1/2" shanks. Entry door profile router bits allow you to convert thick Tongue and Groove doors into rail and stile doors by adding a cope and stick profile to the inside edge of the rails and stiles. These bits are great for custom door shops that create all their doors as Tongue and Groove and then add the design profile later. The blades are C3 micro-grain carbide Tipped.

Read more
Go to Shop
yonico Yonico 12134q Panel Raiser Router Bit with Ogee 1-Inch Depth 1/4-Inch Shank
₱ 2,501.00
Galleon

This Yonico 12134q router bits can be used to cut cabinet door center panels as well as base boards, casings, etc. This is a wide diameter bit with 1/4" shank, therefore extra precautions such as reducing the feed rate and cutting at multiple depth stops should be taken. Other Yonico router bit options are the Yonico 12147q (vertical) or the Yonico 12134 (1/2" shank).

Read more
Go to Shop
yonico Yonico 16147 Huge Crown Molding Router Bit 1/2-Inch Shank
₱ 2,397.00
Galleon

This beautiful profile will cut very large 2-1/2" crown moldings while saving you a fortune. Combine with our crown molding extender to really stretch your possibilities. Use your imagination... Due to the large size of this cutter, be sure to make multiple passes to achieve full profile depth. Blades are 2 flute, premium K10 carbide and shank is 1/2".

Read more
Go to Shop
yonico Yonico 15129q Small Lock Miter 45Degree Router Bit, 1/2"
₱ 1,883.00
Galleon

Use the reversible 45° lock miter glue joint router bit to join boards at 90°. The interlocking 45° cuts will produce extremely strong joints without having to struggle to keep the boards in place during clamping. Additionally, it will provide extra gluing surface resulting in an extremely strong and durable joint. When positioned properly, the bit will cut both pieces of stock without having to adjust the bit. Simply set the center of the stock to the center of the bit. Then, cut one piece horizontally and the second one vertically. Ideal for use with stock between 3/8" and 1/2" thick. Two flute carbide cutters & 1/4" shank.

Read more
Go to Shop
yonico Yonico 14183 Number 10 Biscuit Joint Slot Cutter Jointing/Slotting Router Bit 1/2-Inch Shank
₱ 1,421.00
Galleon

The Yonico 14183 #10 biscuit joint router bit cuts perfect sized slots for #10 biscuits. With a 13/32" cutter depth, this slot cutter is designed to cut an extra 32nd of an inch giving room for biscuit expansion. 2 flute C3 tungsten carbide cutters, 1/2" shank.

Read more
Go to Shop
yonico Yonico 14976 Bottom Cleaning Dado Router Bit with 1-1/2-Inch X 9/16-Inch 1/2-Inch Shank
₱ 2,579.00
Galleon

Cut perfectly clean 1-1/2" wide dados with the Yonico 14976 bottom cleaning router bit. The two cutters meet in the center of the bit which leaves behind a very cleanly routed path. Can also be used to clear larger areas of material. 1/2" shank.

Read more
Go to Shop
yonico Yonico 14123q Flush Trim 1/2-Inch W x 3/4-Inch H Router Bit Shank Bearing 1/4-Inch Shank
₱ 1,079.00
Galleon

Great for combined plunge-cutting and pattern/template routing. For increased work piece visibility use the shank bearing flush trim bit in a handheld router allowing the template to be positioned on top of the work piece. In a router table, template will be positioned underneath the work piece. Can be used without the bearing as a standard straight bit. Two flute carbide cutters with enclosed ball bearing. 1/4" shank. 1/2" Diameter, 3/4" Cutter Length, 2-1/4" Overall Height

Read more
Go to Shop
yonico Yonico 15220 22.5-Degree Lock Miter Glue Joint Router Bit Set 1/2-Inch Shank
₱ 3,725.00
Galleon

This set will cut 22.5 degree miters to make 45 degree joints. Put a 45 degree joint in place of a 90 degree angle to soften a sharp look. Then, you can cover the new surface with a column for added beauty. Great for 8 sided projects such as planters. Two

Read more
Go to Shop
yonico Yonico 13001 7-1/4" Radius Guitar Finger Board Radiusing Router Bit with 1/2" Shank
₱ 2,609.00
Galleon

Replicate the comfort and playability of a vintage fender strat by adding a 7-1/4" radius to your guitar's fretboard using the Yonico 13001 radiusing router bit. This bit has a radiused cutting height of 1-7/8" for fretboards up to 3-3/4" wide. The bit features C3 premium micro grain carbide and 1/2" shank. A unique way to add a radius to your stringed instrument's fretboard. These radiusing bits will eliminate the excessive effort required for using a sanding block. Tape the finger board to a perfectly squared board and slide along the router table fence with the top of the bit's blade running at the height of the center line of the finger board. This will radius one half of the board. Then flip the stock to radius the other half. Yonico fretboard radiusing router bits come in radiuses of 7-1/4", 8-1/2", 9-1/2", 10", 12" & 16".

Read more
Go to Shop
yonico Yonico 16121 Large Elaborate Chair Rail Molding Router Bit 1/2-Inch Shank
₱ 1,991.00
Galleon

Features1/2"; ShankIndustrial QualityC3 Tungsten Carbide CuttersSolid Hardened Steel BodyAnti-Kickback DesignBuild-Up Resistant Teflon CoatingLifetime WarrantySatisfaction GuaranteedCreate beautiful large chair rail moldings with the Yonico 16121 router bit. An easy upgrade to any room.

Read more
Go to Shop
yonico Yonico 14360q 3 Bit Core Box Long Reach Router Bit Set, 1/4-Inch Shank
₱ 2,190.00
Galleon

Designed for sign making and general round nose grooving. Includes 3 core box router bits with diameters - 1/4", 3/8" & 1/2". With an overall height of 2-3/8", the Yonico 14360q router bit set is ideal for long reach core box grooving. Two flute carbide cutters and 1/4" shanks.

Read more
Go to Shop
yonico Yonico 14706 Rabbet Router Bit & Bearing Set with 1/2" Shank
₱ 3,617.00
Galleon

This large Rabbeting set is capable of 6 different cutting depths by just selecting the desired bearing. The depths include 3/8", 1/2", 9/16", 5/8", 11/16" & 3/4". the large 1" cutting height is sufficient for even the largest Rabbeting jobs. The 6 bearing diameters are: 3/8", 1/2", 5/8", 3/4", 7/8" and 1-1/8" with inner diameters of 3/16". two flute carbide cutters and 1/2" shank. With the included additional bearings, this rabbet router bit set becomes very useful and practical. You can easily remove the existing bearing and replace with the bearing that will give you the depth needed for your project.

Read more
Go to Shop
yonico Yonico 12401 4 Bit Drawer Front and Cabinet Door Front Router Bit Set with 1/2-Inch Shank
₱ 5,197.00
Galleon

Add a choice of 4 edgings to your drawer and cabinet door fronts. This Yonico 12401 edging set includes 1 thumbnail bit, 2 ogee bits (1 large and 1 small) and 1 round-over with ogee bit. 1/2" Shanks.

Read more
Go to Shop
yonico Yonico 14700 Slot Cutter 3 Wing Router Bit Set with 1/2-Inch and 1/4-Inch Shank 1/2-Inch Shank, 6-Piece
₱ 4,269.00
Galleon

Includes 6 sizes of 3 wing slot cutters, 2 arbors and a 7/8" bearing. A most practical set to keep handy, the Yonico 14700 slot cutter set features 6 slot cutters in the following sizes: 1/16", 3/32", 1/8", 5/32", 3/16" and 1/4". (or 2/32", 3/32", 4/32", 5/32", 6/32" and 8/32") Two flute carbide cutters and 1/2" shanks.

Read more
Go to Shop
yonico Yonico 31313-SC CNC Router Bit Up Cut Solid Carbide with 1/4" Shank, 7/32" x 1" x 1/4" x 2-1/2"
₱ 1,831.00
Galleon

Best used for: Standard milling, dadoing, and boring.• Cutting Diameter: 7/32" • Cutting Height: 1" • Shank Diameter: 1/4" • Overall Length: 2-1/2" • Flutes: 3 Up-cut end mills direct woodchips up and away from the milling area leaving an unobstructed path for the endmill. Bit breakage is less likely. Up cut end mills are the best choice for most standard milling applications. The up cut direction can leave behind a minimally rough top surface edge.

Read more
Go to Shop
yonico Yonico 15136 Glue Joint Router Bit with Medium Reversible 1/2-Inch Shank
₱ 1,903.00
Galleon

Rout both joining cuts with one reversible bit! Simply set the center of the bit with the center of the stock. Run one cut face up and the adjoining cut face down to create a perfect joint. Great for edge- joining tabletops, door panels and even flooring, among many other glue joint projects. Two flute carbide cutters and shank is 1/2".

Read more
Go to Shop
yonico Yonico 14979 Faux Panel Roman Ogee Router Bit with C3 Carbide Tipped 1/2" Shank
₱ 1,135.00
Galleon

This bit has a cutting diameter of 3/4" and a 1/2" cutting depth. The Roman Ogee design radius is 1/8". this bit also comes equipped with a 3/4" diameter Radial bearing for template work Held on to the shank with a metal sleeve. Two flute carbide center meeting cutters and 1/2" shank. Plunge cutting faux panel doors is a practical shortcut to achieving the look of raised panel doors with less sweat and comparable beauty. Ogee Groove router bits are a popular choice for making faux panel kitchen cabinet doors. These bits can transform a Flat panel into a beautiful rail and stile alternative. While Often used in CNC machines, profile Groove bits can also be used in a handheld router using a fairly simple perimeter Jig.

Read more
Go to Shop
yonico Yonico 16123 Door and Window Casing Router Bit 1/2-Inch Shank
₱ 2,347.00
Galleon

Create beautiful door and window casings using this Yonico 16123 casing router bit. Casings conceal open seams around newly installed windows and doors. Using this bit you can create casings that are at least 2 inches wide.

Read more
Go to Shop
yonico Yonico 16166 Mitered Door Molding Router Bit 1/2-Inch Shank
₱ 2,272.00
Galleon

The Yonico 16166 molding router bit will make dramatic mitered doors, picture and mirror frames, chair rails, crown moldings and other decorative trim. With a cutter height of 2-9/16", this large and majestic molding router bit will greatly enhance the design of your doors, furniture and walls. Combine the Yonico 16166 with any of our raised panel router bits to create highly decorative raised panel doors. This mitered door molding bit is designed to work with 2-13/16" wide stock and a recommended thickness of at least 3/4". The Yonico 16166 is manufactured using highest grade materials including c3 micrograin carbide blades and a solid hardened steel body. Two flute carbide cutters and 1/2" shank. Enjoy years of routing with another excellent Yonico router bit!

Read more
Go to Shop
yonico Yonico 18134 Wavy Jewelry Box Side Wall Router Bit 1/2-Inch Shank
₱ 2,636.00
Galleon

Use the Yonico 18134 router bit to add a classic tall ogee design to jewelry and keepsake boxes. This bit can also be used for simple yet elegant crown moldings.

Read more
Go to Shop
Yonico 15229 Flooring 2 Bit Tongue and Groove Router Bit Set with 1/2" Shank
₱ 3,119.00
Takatack
Go to Shop
yonico Yonico 15228 Yonico 15228 Tongue and Groove Router Bit Set 1/4" x 1/4" 1/2" Shank, ,
₱ 3,521.00
Galleon

Cut versatile ¼” x ¼” tongue and groove joints with the Yonico 15228 Tongue and Groove Router bit set. This set is great for all types joinery applications. This set includes separate tongue and groove bits eliminating the need to reassemble the bits for the tongue and groove cuts. Use with stock up to 3/4" thick. High quality C3 carbide tipped, 3 wing cutters. Fully enclosed 7/8” outer diameter guide bearings. 1/2" shanks.

Read more
Go to Shop
yonico Yonico 12131 2-1/2" Diameter Cove Raised Panel Router Bit with 1/2" Shank
₱ 2,568.00
Galleon

This 2-1/2" cove panel raiser has a cutting depth of 1" and a total cutting height of 7/16" which includes a 1/8" fillet. This bit can cut panels for door frames with grooves of up to 3/8" deep. This bit features thick carbide cutters and a 1/2" shank. Use a raised panel router bit to reduce the thickness of the center panel of rail and stile doors while at the same time adding a beautiful profile to the edge. Install one of these bits in your Table mounted router and route your panels face down. Raised panel router bits have a large diameter and remove a lot of material, so make sure you have a router with enough Horsepower to handle this kind of work. All standard raised panel bits are fitted with Radial bearings to make adjustment of the router Table fence easy. Do not use these bits in handheld routers. If you are using stock that is very thick, choose one of our raised panel router bits with a backcutter blade. These will remove excess stock from the back of the panel as well.

Read more
Go to Shop
yonico Yonico 12145 Panel Raiser Router Bit with Vertical Cove 1/2-Inch Shank
₱ 2,058.00
Galleon

Create cove raised panels for cabinet doors vertically with the Yonico 12145 vertical panel raiser router bit. Two flute carbide cutters & 1/2" shank. Manufactured from C3 micrograin carbide, Yonico raised panel router bits create smooth, detailed cuts resulting in professional door panels.

Read more
Go to Shop
yonico Yonico 18123 Handrail Router Bit 1/2-Inch Shank
₱ 2,338.00
Galleon

Create your own custom railings and handrails. Two flute carbide cutters with ball bearing guide. Shank is 1/2".

Read more
Go to Shop
yonico Yonico 15330 Multi Sided Glue Joint Router Bit Set 1/2-Inch Shank
₱ 4,878.00
Galleon

Multi-sided glue joint bits make joining up multi-sided projects easy. Columns, barrels and planters to name a few can grace your décor with minimal effort. Using these bits, you will only need to cut one end as opposed to two (such as with miter joints) reducing cutting time in half! Bits are designed to cut at the correct angle providing extra gluing surface and a strong mechanical joint. When glued together, the routed end hugs the mating piece preventing any slippage. Choose the desired bit and cut according to the amount of sides needed for your project. Cut face up for six or eight sided projects and face down for twelve or sixteen sided projects. Edges can be cut either flush or protruded, then sanded down later to the desired finish. Set comes in a solid wood storage case. Two flute carbide cutters and 1/2" shanks.

Read more
Go to Shop
yonico Yonico 14460q 4 Bit Round Nose Router Bit Set, Plunge 1/4-Inch Shank
₱ 2,397.00
Galleon

The Yonico 14460q round nose router bit set is a multi function set otherwise known as core box bits. Cut grooves in virtually anything wood such as drawers, doors, trimming and columns. Great for sign making and wooden toy grooving. Includes 4 round nose router bits with the following measurements: • 3/8" Diameter Long Reach - no Bearing - 1" Cutter Height, 2-5/8" Overall Height •1/2" Diameter with Bearing - 1-1/4" Cutter Height, 2-7/8" Overall Height • 5/8" Diameter with Bearing - 1-1/4" Cutter Height, 2-7/8" Overall Height • 3/4" Diameter with Bearing - 1-1/4" Cutter Height, 2-13/16" Overall Height Two flute carbide cutters and 1/4" shanks.

Read more
Go to Shop
yonico Yonico 12121 Rail and Stile Router Bit Ogee Stacked 1/2-Inch Shank
₱ 2,734.00
Galleon

The Yonico Stacked Rail and Stile Router Bit will cut both rail and stile in a beautiful ogee design. Use with stock between 3/4" - 15/16" thickness. Simply cut the stile and then lower the bit in your table to make the rail cuts. No need to switch or reassemble cutters. Two flute carbide cutters with ball bearing guide. Shank is 1/2".

Read more
Go to Shop
yonico Yonico 15127 Medium Lock Miter Router Bit with 45-Degree 3/4-Inch Stock 1/2-Inch Shank
₱ 2,609.00
Galleon

Use the reversible 45Degree lock miter glue joint router bit to join boards at 90Degree. The interlocking 45Degree cuts will produce extremely strong joints without having to struggle to keep the boards in place during clamping. Additionally, it will provide extra gluing surface resulting in an extremely strong and durable joint. When positioned properly, the bit will cut both pieces of stock without having to adjust the bit. Simply set the center of the stock to the center of the bit. Then, cut one piece horizontally and the second one vertically. Ideal for use with 3/4" stock. Two flute carbide cutters & 1/2" shank.

Read more
Go to Shop
yonico Yonico 15229 Flooring 2 Bit Tongue and Groove Router Bit Set with 1/2" Shank
₱ 3,485.00
Galleon

This mini V-Groove Tongue and Groove set is great for 5/8" stock and can also be used as a standard Tongue and Groove for stock as small as 3/8". the Tongue and Groove section measures 1/4" deep x 3/16" high. 1/2" shanks a Tongue and Groove joint is the ideal way to create Flat, even joints for flooring, wainscoting, panels and tabletops. Tongue and Groove router bits will cut the 2 mating profiles for this easy to make woodworking joint with ease and with a simple setup. This joint also provides a lot of gluing surface as well as aligning ease. Tongue and Groove bits can take quite a big bite out of the wood, so using these bits in a router Table is strongly recommended. Even though some smaller Tongue and Groove bits can be utilized in a hand-held router the stability of a Table will help keep the joint perfectly square. For best results, use with solid wood only.

Read more
Go to Shop
yonico Yonico 13189 Classical Cove Edging Router Bit with 3/16" Radius and 1/2" Shank
₱ 1,694.00
Galleon

This cove and bead bid can be used as a edging bit as well as a mini crown molding. The bit's cove profile with the added beads will add sleek lines to your project. The Yonico 13189 creates a 3/16" radius cove with beads.

Read more
Go to Shop
yonico Yonico 16142 Crown Molding Router Bit Extender 1/2-Inch Shank
₱ 1,991.00
Galleon

Crown Molding Extender Router Bit will cut very large custom crown moldings. You can also double the height of your crown molding to 4-1/2" by flipping the stock after finishing the first cut, then running again. Additionally, the extender bit can be combined with any of our other crown molding bits to create your own custom design crown moldings up to 4-3/4" high. Due to the large size of this cutter, be sure to make multiple passes to achieve full profile depth. Blades are double fluted and made of premium k10 carbide. Shank is 1/2".

Read more
Go to Shop
yonico Yonico 17150q 15 Bit MultiProfile Router Bit Set with 1/4" Shank
₱ 5,924.00
Galleon

Great value starter set! This set contains 15 essential bits needed for the most common routing tasks making this the perfect set for beginners. This set also includes a beautiful solid wood storage case. The bits in this set are of the same top quality workmanship you have come to expect from Yonico router bits. All the bits in this set are C3 carbide tipped and have 1/4" shanks. Included bits: • 1/4" Dado Straight Bit • 3/8" Dado Straight Bit • 1/2" Dado Straight Bit • 1 x 1/2" Flush Trim Straight Bit • 1/2" X 3/4" Template Trim Bit • 14° Dovetail Joint Bit • 15° Bevel Trim Bit • 3/8" Roman Ogee Edging Bit • 45° Chamfer Edging Bit • 1/4" Radius Round Over Edging Bit • 1/2" Radius Round Over Edging Bit • 1/4" Radius Cove Edging Bit • 1/2" Radius Cove Edging Bit • 1/4" Slotting Bit • 1/2" Slotting Bit.

Read more
Go to Shop
yonico Yonico 31010-SC CNC Router Bit Low Helix Up Cut Shank, 1/4-Inch X 1-Inch X 1/4-Inch X 2-1/2-Inch 1/4-Inch
₱ 1,322.00
Galleon

Best for achieving smooth finish on hard plastics.• Cutting Diameter: 1/4" • Cutting Height: 1" • Shank Diameter: 1/4" • Overall Length: 2-1/2" • Flutes: 2 Low Helix bits perform a more lateral movement with less lift resulting in a smoother finish. These bits are a better choice for hard plastics such as acrylic and phenolic. Up-cut end mills direct chips up and away from the milling area leaving an unobstructed path for the endmill. Bit breakage is less likely.

Read more
Go to Shop
yonico Yonico 14142 Flush Trim Router Bit End Bearing with 2-Inch X 1/2-Inch 1/2-Inch Shank
₱ 1,499.00
Galleon

Use flush trim bit with laminates, ply-woods, soft & hard woods, composites, plastics and some non-ferrous metals. Designed to provide precise, efficient cuts and extremely durable. The enclosed ball bearing guide ensures smooth running. Shank is 1/2".

Read more
Go to Shop
yonico Yonico 12404 4 Bit Vertical Raised Panel Router Bit Set with 1/2-Inch Shank
₱ 4,909.00
Galleon

Own 4 of the most popular vertical panel raiser profiles in this impressive 4 bit router bit set. The Yonico 12404 router bit set includes the following 4 vertical panel raiser designs: bevel, ogee, ogee & bead and cove. All bit shanks are 1/2" with a cutter length of 1-1/2". Manufactured from C3 micrograin carbide, the Yonico 12404 set will yield years of raised panel cabinet making. Set includes a beautiful solid wood storage case.

Read more
Go to Shop
yonico Yonico 14522q 5 Bit Straight/Dado Router Bit Set with 1/4" Shank
₱ 2,631.00
Galleon

This 5 piece straight router bit set is a great choice for all kinds of dado and straight cut routing. The set includes 5 very useful cutting diameters to cut that perfect dado. This set also comes in a beautiful solid wood storage case. The cutting diameters are: 1/4", 3/8", 1/2", 5/8" and 3/4". The 1/4" bit has a solid carbide insert blade which enhances the strength of small diameter bits. The shank diameters are 1/4". Straight router bits are the most widely used and versatile bits in woodworking. They are ideal for joinery such as box joints, lap joints, dados, rabbets, mortises and tenons. You can also use straight bits for trimming operations and CNC work.

Read more
Go to Shop
yonico Yonico 14172q Template Trim Router Bit with Bottom Cleaning 1/4-Inch Shank
₱ 1,881.00
Galleon

Yonico 14172q Template Trim Router Bit will route clean cutouts for hinges or other template trim projects. Center meeting blades leave behind a perfectly clean routed area. Two flute carbide cutters with 1/4" shank.

Read more
Go to Shop
yonico Yonico 14190q T-Slot Cutter Router Bit for 3/8-Inch Hex Bolt Heads 1/4-Inch Shank
₱ 1,263.00
Galleon

Great for your custom jig creations, the Yonico 14190q T-slot router bit cuts T-slots for standard 3/8"; wide hex-bolt heads.

Read more
Go to Shop
yonico Yonico 14137 Pattern/Flush Trim Router Bit with 3/4-Inch W X 1-1/2-Inch H 1/2-Inch Shank
₱ 1,625.00
Galleon

Great for combined plunge-cutting and pattern and template routing. For increased work piece visibility, use in a handheld router allowing the template to be positioned on top of the work piece. In a router table, template will be positioned underneath the work piece. Can be used without the bearing as a standard straight bit. Two flute carbide cutters with enclosed ball bearing. Shank: 1/2"; - Width: 3/4"; - Cutter Height: 1-1/2";Features1/2"; ShankIndustrial QualityMicro-Grain C3 Tungsten Carbide CuttersSolid Hardened Steel BodyAnti-Kickback DesignBuild-Up Resistant CoatingLimited Lifetime WarrantySatisfaction Guaranteed

Read more
Go to Shop
yonico Yonico 12349 Shaker 3 Bit Raised Panel Cabinet Door Router Bit Set with 1/2" Shank
₱ 5,267.00
Galleon

This 3 bit cabinet door router bits set includes a set of matched shaker rail and stile bits for stock between 5/8" and 7/8" thick and a 2-3/4" shaker panel raiser with a backcutter for stock up to 1" thick. 1/2" shanks. Rail and stile door construction has been around for centuries and is the most common way to build doors for cabinets and furniture. Our rail and stile router bits will enable you to create your own frame-and-panel doors. Cope the ends of your rails with one bit, and then switch to the second bit to route the inside edge profile in all your door parts. The included panel raiser cuts the artistic profile on the center panel which reduces the panel's thickness to properly fit in the door frame's Groove.

Read more
Go to Shop
yonico Yonico 17150 Yonico 17150 15 Bit MultiProfile Router Bit Set 1/2" Shank, ,
₱ 6,618.00
Galleon

Great value starter set! This set contains 15 essential bits needed for the most common routing tasks making this the perfect set for beginners. This set also includes a beautiful solid wood storage case. The bits in this set are of the same top quality workmanship you have come to expect from Yonico router bits. All the bits in this set are C3 carbide tipped and have 1/2" shanks. Included bits: • 1/4" Dado Straight Bit • 3/8" Dado Straight Bit • 1/2" Dado Straight Bit • 1 x 1/2" Flush Trim Straight Bit • 1/2" X 3/4" Template Trim Bit • 14° Dovetail Joint Bit • 15° Bevel Trim Bit • 3/8" Roman Ogee Edging Bit • 45° Chamfer Edging Bit • 1/4" Radius Round Over Edging Bit • 1/2" Radius Round Over Edging Bit • 1/4" Radius Cove Edging Bit • 1/2" Radius Cove Edging Bit • 1/4" Slotting Bit • 1/2" Slotting Bit.

Read more
Go to Shop
yonico Yonico 12243q Rail and Stile Router Bits with 2 Bit Standard Ogee 1/4-Inch Shank
₱ 3,647.00
Galleon

Yonico rail and stile router bit set (12243q) will cut rail & stile for cabinet doors in the classic ogee design. Fully enclosed ball bearing guides allow for precise rail and stile cuts without the use of a fence. Yonico rail and stile router bits produce impressive and perfect results with every cut yielding years of woodworking satisfaction. Two flute carbide cutters & 1/4" shanks.

Read more
Go to Shop
yonico Yonico 31261-SC CNC Router Bit Up Cut Solid Carbide with 1/2-Inch X 1-1/4-Inch X 1/2-Inch X 3-Inch 1/2-Inch Shank
₱ 3,312.00
Galleon

Best used for: Standard milling, dadoing, and boring.• Cutting Diameter: 1/2" • Cutting Height: 1-1/4" • Shank Diameter: 1/2" • Overall Length: 3" • Flutes: 2 Up-cut end mills direct woodchips up and away from the milling area leaving an unobstructed path for the endmill. Bit breakage is less likely. Up cut end mills are the best choice for most standard milling applications. The up cut direction can leave behind a minimally rough top surface edge.

Read more
Go to Shop
yonico Yonico 37412-SC 1/16" 4 Flute Taper Spiral ZRN Coated CNC Router Bit with 1/4" Shank
₱ 2,146.00
Galleon

This tapered end mill has a 1/16" radius cutting tip and a 1" cutting length. The 4 flutes and the ZRN coating provide great performance and extended tool life. Tapered CNC end mills with ZRN coating provide the extra length needed to carve 3D shapes out of solid wood, plastic, foam and other materials. The tapered design provides added strength to the bit while still maintaining a small radius at the bit's tip. This unique design provides clearance when routing 3D profiles and allows you to create complex carvings in all kinds of stock. With the added ZRN coating, the bit’s lifespan and durability are increased substantially avoiding unnecessary down time.

Read more
Go to Shop
yonico Yonico 16137 Architectural Molding Router Bit 1/2-Inch Shank
₱ 2,112.00
Galleon

Add ‘English and Colonial’ beauty to large and small furniture and cabinet doors. Use for crown moldings, baseboards and large picture frames as well. Two flute carbide cutters with ball bearing guides. 1/2" shank.

Read more

yonico Online Store Philippines

Yonico 13124 Double Roman Ogee Edging Router Bit Large 1/2-Inch Shank, Yonico 12339q Rail and Stile with Panel Raiser Router Bit Set Cove 1/4-Inch Shank, 3-Piece, Yonico 14220 Solid Carbide Flush Trim Spiral Router Bit Set and 1/4" are topselling products from yonico. If your budget is ₱ 807.00 - ₱ 12,814.00, yonico products are perfect for you! From Hobbies, Gifts and Groceries, you can find varieties of products from yonico that would suit you.